• Number of pins: 2
• Colour: blue
• Manufacturer: JP GROUP
• Lisainfo: Temperature sensor for cooling system, 2 pins
• Additional information: Temperature sensor for cooling system, 2 pins

• Operating voltage [V]: 12
• Switch point from [°C]: 84, 91
• Switch point to [°C]: 95, 102
• Spanner Size: 29
• Supplementary Article/Info 2: with seal ring
• Colour: black
• Thread Size: M22 x 1,5
• Number of pins: 3
• Manufacturer: JP GROUP
• Lisainfo: Thermo switch for fan 102-91/95-84 C
• Additional information: Thermo switch for fan 102-91/95-84 C

• Inner Diameter [mm]: 19.5
• Thickness [mm]: 3.5
• Material: Rubber
• for OE number: 7198663
• Manufacturer: DELLO AUTOMEGA

• Inner Diameter [mm]: 19.5
• Thickness [mm]: 3.5
• Weight [kg]: 0.001
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• General Information: temperature sensor
• Manufacturer: VIKA

• Colour Coding: black
• Spanner Size: 13
• Thread Size: M10x1
• Number of pins: 1
• Plug Type: Blade Terminal
• Supplementary Article/Supplementary Info: with gasket/seal
• for OE number: 7203359
• Manufacturer: DELLO AUTOMEGA

• for OE number: 025906041A
• Housing Colour: blue
• Manufacturer: KAMOKA

• for OE number: 357919501A
• Manufacturer: KAMOKA

• for OE number: 1331294
• Number of pins: 4
• Supplementary Article/Info 2: with seal ring
• Fitted Diameter [mm]: 20
• Manufacturer: KAMOKA

• Number of pins: 2
• Temperature range from [°C]: 55
• Temperature range to [°C]: 65
• Colour Coding: red
• Manufacturer: JP GROUP
• Lisainfo: Thermo switch for cooling system, 55-65 C
• Additional information: Thermo switch for cooling system, 55-65 C

• for OE number: 191 919 369 A S1
• Housing Colour: white
• Manufacturer: KAMOKA

• for OE number: 191919369A
• Manufacturer: KAMOKA

• Sensor Type: NTC Sensor
• Mounting Type: Clamped
• Connector Shape: rectangular
• Number of pins: 2
• for OE number: 025906041A
• Supplementary Article/Info 2: with mounting parts
• Manufacturer: NRF

Manufacturer: FAE

• Supplementary Article/Info 2: with seal ring
• Number of pins: 2
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Engine Code: 1F
• Thread Size: M10x1
• Spanner Size: 13
• Corresponds to the original part in colour: white
• Manufacturer: FACET

• Switch Point [°C]: 120
• Thread Size: 20 mm
• Sensor Type: Closed-type Sensor
• Manufacturer: VERNET

• Colour: black
• Spanner Size: 29
• Connector Shape: rectangular
• Manufacturer: KAMOKA

• Engine Code: 1F
• Thread Size: M10x1
• Spanner Size: 13
• Corresponds to the original part in colour: white
• Manufacturer: EPS

• new version:
• Outer Diameter [mm]: 20
• Number of connectors: 4
• Colour: black
• Colour Coding: blue
• Supplementary Article/Info 2: without seal ring
• Weight [kg]: 0.023
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thread Size: M10x1.0
• Manufacturer: VERNET

• for OE number: A0015403045
• Colour: grey
• Spanner Size: 29
• Manufacturer: KAMOKA

• Sensor Type: NTC Sensor
• Mounting Type: Clamped
• Connector Shape: rectangular
• Number of pins: 4
• Socket colour: black
• for OE number: 357919501A
• Supplementary Article/Info 2: with seal ring
• Manufacturer: NRF

• Number of connectors: 2
• Colour: blue
• Weight [kg]: 0.015
• Supplementary Article/Supplementary Info: with retaining spring, with gasket/seal
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Sensor Type: NTC Sensor
• Connecting thread: M10 x 1
• Manufacturer: ERA

• new version:
• Outer Diameter [mm]: 20
• Number of connectors: 4
• Colour: black
• Colour Coding: blue
• Supplementary Article/Info 2: without seal ring
• Weight [kg]: 0.023
• Name: SW 30 93 0616
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: 1F
• Colour: blue
• Number of pins: 2
• Manufacturer: FACET

• Engine Code: 1F
• Colour: blue
• Number of pins: 2
• Name: EP 1.830.101
• Manufacturer: EPS

• Number of connectors: 2
• Colour: blue
• Weight [kg]: 0.015
• Supplementary Article/Supplementary Info: with gasket/seal, with retaining spring
• Name: SW 30 93 4762
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Connector Shape: rectangular
• Material: Brass
• Number of pins: 1
• Plug Type: Male
• Sensor Type: NTC Sensor
• Spanner Size: 14 mm
• Thread Size: M10x1,0
• Name: NI 207058
• Manufacturer: NISSENS

Technical Information: FIRST FIT - a time-saving installation! Find all additional parts such as O-rings, clip, washer in the box.

• Operating temperature from [°C]: 112
• Operating temperature to [°C]: 120
• Thread Size: 20 mm
• Manufacturer: VERNET

• Length [mm]: 37
• Weight [kg]: 0.02
• Supplementary Article/Info 2: with seal ring
• for OE number: 025 906 041 A
• Supplementary Article/Supplementary Info: with gasket/seal
• Colour Coding: blue
• Number of pins: 2
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Housing Colour: black
• Colour Coding: yellow
• Corresponds to the original part in colour: blue, yellow
• Number of pins: 4
• Supplementary Article/Supplementary Info: with gasket/seal
• Article number of recommended accessories: 0905458
• Version: IAM
• Power [W]: 0.06
• Manufacturer: METZGER

• Thread Size: M20
• Number of pins: 4
• Supplementary Article/Info 2: without cable
• Connector Shape: rectangular
• Fitted Diameter [mm]: 20
• Manufacturer: ERA

• Operating temperature from [°C]: 95, 102
• Operating temperature to [°C]: 84, 91
• Thread Size: M22x1.5
• Sensor Type: Open-style sensor
• Manufacturer: VERNET

• Thread Size: M20
• Number of pins: 2
• Connector Shape: rectangular
• Manufacturer: ERA

• Sensor Type: NTC Sensor
• Colour: blue
• Number of pins: 2
• Manufacturer: MEYLE

• for model code: For Cooling Fan
• Number of pins: 2
• Connector Shape: rectangular
• Manufacturer: DELPHI
• Name: DE TS10321

• new version:
• Outer Diameter [mm]: 20
• Number of connectors: 4
• Colour: black
• Colour Coding: blue
• Weight [kg]: 0.026
• Supplementary Article/Supplementary Info: with retaining spring, with gasket/seal
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of pins: 4
• Supplementary Article/Info 2: with seal ring
• Colour: black
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Number of pins: 3
• Connector Shape: oval
• Socket colour: black
• Shut-off Point [°C]: 95, 92
• Switch Point [°C]: 85, 102
• Thread Size: M22x1,5 mm
• Spanner Size: 29 mm
• for OE number: 6U0959481A
• Manufacturer: MEAT&DORIA

• Number of pins: 2
• Weight [kg]: 0.3
• Packaging length [cm]: 12
• Packaging width [cm]: 8
• Packaging height [cm]: 6

• Switch Point [°C]: 65
• Number of pins: 2
• Manufacturer: FAE ELEKTRYKA

• Diameter [mm]: 25
• Length [mm]: 42
• Weight [kg]: 0.03
• Supplementary Article/Supplementary Info: with gasket/seal
• for OE number: 6U0 919 501 B
• Colour Coding: blue
• Number of pins: 4
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Vehicle Equipment: for vehicles with air conditioning
• Switch Point [°C]: 119
• Number of pins: 2
• Manufacturer: FAE

• Operating temperature from [°C]: 95, 102
• Operating temperature to [°C]: 84, 91
• Thread Size: M22x1.5
• Sensor Type: Open-style sensor
• Manufacturer: VERNET

• Thread Size: M22x1.5
• Number of pins: 4
• Switch point from [°C]: 120
• Switch point to [°C]: 112
• Manufacturer: ERA

• new version:
• Outer Diameter [mm]: 20
• Number of connectors: 4
• Colour: black
• Colour Coding: blue
• Weight [kg]: 0.026
• Supplementary Article/Supplementary Info: with retaining spring, with gasket/seal
• Name: SW 32 93 9142
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Required quantity: 1
• Vehicle Identification Number (VIN) to: 6K-TR099 000
• Switch Point [°C]: 84
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Thread Size: 22x1,5
• Number of pins: 3
• Manufacturer: FAE ELEKTRYKA

• External Thread Size: M22 x 1,5
• Spanner Size: 29
• Number of connectors: 3
• Colour Coding: black
• Temperature range from [°C]: 95, 102
• Temperature range to [°C]: 84, 92
• Connector Shape: rectangular
• Weight [kg]: 0.048
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: 1F
• Number of pins: 2
• Temperature range from [°C]: 95
• Temperature range to [°C]: 90
• Thread Size: M22x1,5
• Spanner Size: 29
• Name: EP 1.850.027
• Manufacturer: EPS

• Switch Point [°C]: 84
• Switch point from [°C]: 102
• Switch point to [°C]: 91
• Colour Coding: black
• Supplementary Article/Supplementary Info: with gasket/seal
• Spanner Size: 29
• Number of pins: 3
• Manufacturer: METZGER

• Engine Code: 1F
• Colour: yellow
• Number of pins: 4
• Corresponds to the original part in colour: yellow, blue, black
• Manufacturer: FACET

• Engine Code: 1F
• Colour: yellow
• Number of pins: 4
• Corresponds to the original part in colour: yellow, blue, black
• Name: EP 1.830.146
• Manufacturer: EPS

• Length [mm]: 29
• Height [mm]: 45
• Weight [kg]: 0.073
• Thread Size: M22x1,5
• Switch Point [°C]: 102, 85
• Colour: black
• Switch: with double thermal switch
• Supplementary Article/Supplementary Info: with gasket/seal
• Number of pins: 3
• Switch point from [°C]: 102
• Switch point to [°C]: 85
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Vehicle Equipment: for vehicles with air conditioning
• Number of pins: 3
• Switch point from [°C]: 90
• Switch point to [°C]: 79
• Manufacturer: FAE

• Engine Code: 1F, AKL/APF/AUR, ABU/AEH
• Thread Size: M22*1.5
• Spanner Size: S29
• Number of pins: 3
• Connector Shape: rectangular
• Manufacturer: DELPHI

• Engine Code: 1F
• Vehicle Identification Number (VIN) to: 6K-TR099000
• Thread Size: M22x1,5
• Spanner Size: 29
• Name: EP 1.850.635
• Manufacturer: EPS

• Engine Code: 1F
• Vehicle Identification Number (VIN) from: 6K-TR099001
• Thread Size: M22x1,5
• Spanner Size: 29
• Corresponds to the original part in colour: blue, black
• Name: EP 1.850.652
• Manufacturer: EPS

• Number of pins: 1
• Weight [kg]: 0.3
• Packaging length [cm]: 12
• Packaging width [cm]: 8
• Packaging height [cm]: 6

• Engine Code: 1F
• Number of pins: 2
• Colour: white
• Warn Temperature [°C]: 120
• Manufacturer: EPS

• Vehicle Equipment: for vehicles with air conditioning
• Switch Point [°C]: 3
• Manufacturer: FAE

• Engine Code: 1F
• Number of pins: 2
• Colour: red
• Warn Temperature [°C]: 60
• Manufacturer: EPS