• Inner Diameter [mm]: 57.85
• Lisainfo: Seal, turbo air hose
• Additional information: Seal, turbo air hose

• for PR number: T59
• Weight [kg]: 0.005
• Inner Diameter [mm]: 46
• Packaging length [cm]: 5.5
• Packaging width [cm]: 5.5
• Packaging height [cm]: 0.4
• Manufacturer: FEBEST

• Inner Diameter [mm]: 57.85
• Material: FPM (fluoride rubber)
• Manufacturer: ELRING

• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 54
• Manufacturer: ELRING

• Quantity per packing unit: 5
• Inner Diameter [mm]: 46.2
• Material: FPM (fluoride rubber)
• Manufacturer: ELRING

• Inner Diameter [mm]: 57.85
• Name: DRM 01815
• Manufacturer: DR.MOTOR AUTOMOTIVE

• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 61.9
• Manufacturer: ELRING

• Fitting Position: Charge Air Cooler
• Manufacturer: DRM

Name: USZCZELKA PRZEWODU CHODNICY POWIETRZA VW GOLF 2.0TDI 07-

• for PR number: T59
• Weight [kg]: 0.005
• Inner Diameter [mm]: 58
• Packaging length [cm]: 6.9
• Packaging width [cm]: 6.9
• Packaging height [cm]: 0.5
• Manufacturer: FEBEST

• for OE number: 3C0145117H
• Weight [g]: 13
• Name: IM 20281
• Manufacturer: ORIGINAL IMPERIUM

• for OE number: 3C0145117F
• Weight [g]: 12
• Name: IM 20282
• Manufacturer: ORIGINAL IMPERIUM

• for PR number: T59
• Weight [kg]: 0.005
• Inner Diameter [mm]: 62
• Packaging length [cm]: 6.9
• Packaging width [cm]: 6.9
• Packaging height [cm]: 0.5
• Manufacturer: FEBEST

• for OE number: 3C0145117B
• Weight [g]: 11
• Name: IM 20284
• Manufacturer: ORIGINAL IMPERIUM

• Quantity per packing unit: 10
• Diameter [mm]: 56
• Weight [kg]: 0.006
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Quantity per packing unit: 5
• Inner Diameter [mm]: 45.7
• Thickness [mm]: 4.5
• Material: FPM (fluoride rubber)
• Quantity Unit: Packing Unit
• Alternatively:

• Turbocharger Line: Cold Side, Piping to engine block
• Vehicle Identification Number (VIN) to: 5P-8-039 074
• Hose Length [mm]: 145
• Inner Diameter 1 [mm]: 63
• Inner Diameter 2 [mm]: 58
• Manufacturer: DENCKERMANN FILTRY

• Turbocharger Line: Cold Side, Piping to engine block
• Vehicle Identification Number (VIN) from: 5P-8-039 075
• Hose Length [mm]: 105
• Inner Diameter 1 [mm]: 68
• Inner Diameter 2 [mm]: 60
• Manufacturer: DENCKERMANN FILTRY

• Production date from: 01/05
• Production date to: 12/09
• Fitting Position: Outlet
• for OE number: 1K0145838G
• Manufacturer: SASIC

• Production date from: 01/05
• Production date to: 12/09
• Fitting Position: Outlet
• for OE number: 1K0145838S
• Manufacturer: SASIC

• Length [mm]: 140
• for OE number: 1K0 145838 S
• Fitting Position: Charge Air Cooler
• Outer Diameter 1 [mm]: 73
• Outer Diameter 2 [mm]: 80
• Name: KOMPRESSORIOHUVOOLIK
• Manufacturer: BUG

• Quantity per packing unit: 5
• Shape: O-Ring
• Inner Diameter [mm]: 58
• Thickness [mm]: 4.5
• Material: FPM (fluoride rubber)
• Alternatively:

• General Information: pressure hose
• Manufacturer: VIKA

• Fitting Position: Right Rear
• Length [mm]: 100
• Colour: black
• Material: ACM (Polyacrylate)
• Cooling Hose: Turbocharger to piping, Hot Side
• Inner Diameter 1 [mm]: 48
• Inner Diameter 2 [mm]: 55
• Guarantee: 3 years guarantee
• Weight [kg]: 0.18
• Always compare old and new part (in particular OE No.):
• Name: CE 24SKV047
• Manufacturer: ESEN SKV

• for PR number: T59
• Weight [kg]: 0.035
• Quantity: 10
• Packaging length [cm]: 10
• Packaging width [cm]: 10
• Packaging height [cm]: 2
• Inner Diameter [mm]: 58.5
• Outer Diameter [mm]: 69.1
• Thickness [mm]: 4.6
• Manufacturer: FEBEST

• for OE number: 1K0 145 832 B
• Material: Rubber with fabric lining
• Connection Diameter (pressure side) [mm]: 59
• Connection Diameter (suction side) [mm]: 59
• Fabrication Number: GPP-VW-021
• Manufacturer: NTY
• Name: NTY GPP-VW-021

• Material: Rubber with fabric lining
• Supplementary Article/Info 2: with quick couplers
• for OE number: 1K0 145 832 B
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Fitting Position: Charge Air Cooler
• Fabrication Number: GPP-VW-106
• Manufacturer: NTY

• Turbocharger Line: Hot Side, Piping to charge air cooler
• Vehicle Identification Number (VIN) from: 5P-8-039 075
• Hose Length [mm]: 320
• Inner Diameter 1 [mm]: 48
• Inner Diameter 2 [mm]: 48
• Manufacturer: DENCKERMANN FILTRY

• Quantity per packing unit: 5
• Material: FPM (fluoride rubber)
• Shape: O-Ring
• Inner Diameter [mm]: 62
• Thickness [mm]: 4.3
• Quantity Unit: Packing Unit

• General Information: pressure hose
• Manufacturer: VIKA

• Vehicle Identification Number (VIN) from: 5P-8-039 075
• Turbocharger Line: Cold Side, Piping to engine block
• Material: PE (Polyethylene)
• Colour: black
• Hose Length [mm]: 105
• Inner Diameter 1 [mm]: 67.5
• Inner Diameter 2 [mm]: 60
• Observe broschure:
• Manufacturer: GATES

• Turbocharger Line: Hot Side, Piping to charge air cooler
• Vehicle Identification Number (VIN) to: 5P-8-039 074
• Hose Length [mm]: 320
• Inner Diameter 1 [mm]: 48
• Inner Diameter 2 [mm]: 48
• Manufacturer: DENCKERMANN FILTRY

• Vehicle Identification Number (VIN) from: 5P-8-039 075
• Ühenduse läbimõõt (survepool) [mm]: 59
• Ühenduse läbimõõt (imipool) [mm]: 59
• Manufacturer: YSPARTS

• Fitting Position: Right Front
• Cooling Hose: Piping to charge air cooler, Hot Side
• Guarantee: 3 years guarantee
• Weight [kg]: 0.46
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 24SKV005

• Vehicle Identification Number (VIN) to: 5P-8-039 074
• Turbocharger Line: Cold Side, Piping to engine block
• Material: PE (Polyethylene)
• Colour: black
• Hose Length [mm]: 145
• Inner Diameter 1 [mm]: 63
• Inner Diameter 2 [mm]: 58
• Observe broschure:
• Manufacturer: GATES

• Vehicle Identification Number (VIN) from: 5P-8-039 075
• Colour: black
• Material: PE (Polyethylene)
• Inner Diameter 1 [mm]: 68
• Inner Diameter 2 [mm]: 60
• Manufacturer: BORG & BECK

• General Information: pressure hose
• Manufacturer: VIKA

• Fitting Position: Right Front
• Cooling Hose: Piping to charge air cooler, Hot Side
• Guarantee: 3 years guarantee
• Weight [kg]: 0.42
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 24SKV049

• Vehicle Identification Number (VIN) to: 5P-8-039074
• Fitting Position: Right, Lower
• Lisainfo: Charger Intake Hose
• Additional information: Charger Intake Hose

• Vehicle Identification Number (VIN) from: 5P-8-039075
• Fitting Position: Right, Upper
• Manufacturer: JP GROUP
• Lisainfo: Charger Intake Hose
• Additional information: Charger Intake Hose

• Outer Diameter [mm]: 69
• Outer Diameter 1 [mm]: 65
• Manufacturer: FAST

• Outer Diameter [mm]: 69
• Outer Diameter 1 [mm]: 65
• Manufacturer: FAST

• Fitting Position: Left
• Supplementary Article/Supplementary Info: with bulb
• General Information: pressure hose；plastic
• Manufacturer: BORSEHUNG

• Vehicle Identification Number (VIN) from: 5P-8-039 075
• Turbocharger Line: Hot Side, Piping to charge air cooler
• Material: Silicone
• Supplementary Article/Info 2: with hose clip
• Colour: black
• Hose Length [mm]: 320
• Inner Diameter 1 [mm]: 48
• Inner Diameter 2 [mm]: 48
• Observe broschure:
• Manufacturer: GATES-PRZEWODY

• Vehicle Identification Number (VIN) from: 5P-8-039 075
• Turbocharger Line: Hot Side, Piping to charge air cooler
• Material: Silicone
• Colour: black
• Hose Length [mm]: 320
• Inner Diameter 1 [mm]: 55
• Inner Diameter 2 [mm]: 52
• Observe broschure:
• Name: Laadimisohu voolik
• Manufacturer: GAT

• Fitting Position: Right
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Fitting Position: Right, Lower
• Material: AEM (Ethylene Acrylate Rubber)
• Name: KOMPRESSORIOHUVOOLIK
• Manufacturer: MEY

• Vehicle Identification Number (VIN) to: 5P-8-039 074
• Turbocharger Line: Hot Side, Piping to charge air cooler
• Material: PE (Polyethylene)
• Colour: black
• Hose Length [mm]: 320
• Inner Diameter 1 [mm]: 48
• Inner Diameter 2 [mm]: 48
• Observe broschure:
• Manufacturer: GATES

• Vehicle Identification Number (VIN) to: 5P-8-039 074
• Turbocharger Line: Hot Side, Piping to charge air cooler
• Material: PE (Polyethylene)
• Supplementary Article/Info 2: with hose clip
• Colour: black
• Hose Length [mm]: 320
• Inner Diameter 1 [mm]: 48
• Inner Diameter 2 [mm]: 48
• Observe broschure:
• Manufacturer: GATES-PRZEWODY

• Production date from: 01/05
• Production date to: 12/09
• Fitting Position: Charge Air Cooler, Outlet
• for OE number: 1K0145832B
• Name: KOMPRESSORIOHUVOOLIK
• Manufacturer: SAS

• Production date from: 01/05
• Production date to: 12/09
• Fitting Position: Charge Air Cooler, Outlet
• for OE number: 1K0145832E
• Name: KOMPRESSORIOHUVOOLIK
• Manufacturer: SAS

• for OE number: 1K0145834N
• Weight [g]: 433
• Plug connector manufacturer: HENN
• Length [mm]: 280
• Inner Diameter 1 [mm]: 59
• Inner Diameter 2 [mm]: 54
• Name: IM 221925
• Manufacturer: ORIGINAL IMPERIUM

• Fitting Position: Right
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Fitting Position: Lower Left
• Compression ring material: Stainless Steel
• Material: Rubber with fabric lining
• Weight [kg]: 0.413
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Vehicle Identification Number (VIN) from: ******5P*8*039075
• Outer Diameter [mm]: 69
• Turbocharger Line: Turbocharger to charge air cooler
• Fitting Position: Charge Air Cooler, Right
• Outer Diameter 1 [mm]: 65
• Weight [kg]: 0.44
• for OE number: 1K0 145 832 B
• Supplementary Article/Info 2: with quick couplers
• Name: KOMPRESSORIOHUVOOLIK
• Manufacturer: FEB
• Additional information: FE49361
• Lisainfo: FE49361

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Vehicle Identification Number (VIN) to: ******5P*8*039074
• Outer Diameter [mm]: 69
• Turbocharger Line: Turbocharger to charge air cooler
• Fitting Position: Charge Air Cooler, Right
• Outer Diameter 1 [mm]: 65
• Weight [kg]: 0.441
• Supplementary Article/Info 2: with quick couplers
• for OE number: 1K0 145 832 E
• Name: KOMPRESSORIOHUVOOLIK
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Vehicle Identification Number (VIN) from: 5P-8-039 075
• Connection Diameter (pressure side) [mm]: 59
• Connection Diameter (suction side) [mm]: 59
• for OE number: 1K0 145 832 B
• Material: Rubber with fabric lining
• Compression ring material: Stainless Steel
• Weight [kg]: 0.462
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Vehicle Identification Number (VIN) to: 5P-8-039074
• Fitting Position: Charge Air Cooler, Right
• Supplementary Article/Info 2: with quick couplers
• Article number of recommended accessories: 2400581, 2400582
• Manufacturer: METZGER

• Quantity per packing unit: 100
• Inner Diameter [mm]: 45.7
• Thickness [mm]: 4.5
• Material: FPM (fluoride rubber)

• Quantity per packing unit: 100
• Shape: O-Ring
• Inner Diameter [mm]: 58
• Thickness [mm]: 4.5
• Material: FPM (fluoride rubber)

• Quantity per packing unit: 100
• Shape: O-Ring
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 62
• Thickness [mm]: 4.3