• Fitting Position: Front
• Vehicle Equipment: for vehicles with air conditioning
• Colour: black
• Number of pins: 2
• Manufacturer: JP GROUP A/S
• Lisainfo: Sensor, exterior temperature
• Additional information: Sensor, exterior temperature

• Number of connectors: 2
• Material: Plastic
• Lisainfo: Water level switch, washer
• Additional information: Water level switch, washer

• Number of pins: 2
• Connector Shape: D Shape
• Consult accessories list for recommended additional repairs:
• Name: NIVOOLšLITI, PESUVEEKOGUS
• Manufacturer: HAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Colour Coding: grey
• Number of pins: 2
• Manufacturer: JP GROUP
• Lisainfo: Sender for water temperature gauge, 2 pins
• Additional information: Sender for water temperature gauge, 2 pins

• Supplementary Article/Info 2: with plug
• Conductor Number: 2
• Assy./disassy. by qualified personnel required!:
• Name: Kaabli paranduskomplekt, v„listemperatuuri andur
• Manufacturer: ABA

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• for OE number: 95510612500
• Manufacturer: KAMOKA

• Fitting Position: Front
• Colour: black
• Vehicle Equipment: for vehicles with air conditioning
• Number of pins: 2
• Supplementary Article/Info 2: without cable
• Connector Shape: D Shape
• Fabrication Number: ECT-AU-001
• Manufacturer: NTY
• Name: NTY ECT-AU-001

• Colour: black
• Number of pins: 2
• Name: ANDUR,VŽLISTEMPERATUUR
• Manufacturer: MAX
• Lisainfo: 21-0339
• Additional information: 21-0339

• Number of connectors: 2
• Material: Plastic
• Weight [kg]: 0.01
• Name: ANDUR,PESUVEETASE
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Colour Coding: grey
• Fabrication Number: ECT-VW-000
• Manufacturer: NTY
• Name: NTY ECT-VW-000

• General Information: temperature sensor
• Manufacturer: VIKA

• Connector Shape: oval, D Shape
• Colour Coding: grey
• Sensor Type: NTC Sensor
• Number of pins: 2
• Consult accessories list for recommended additional repairs:
• Manufacturer: TOPRAN HANS PRIES

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Quantity per packing unit: 3
• Number of connectors: 2
• Manufacturer: 3RG

• Number of connectors: 2
• Manufacturer: 3RG

• Number of pins: 2
• Connector Shape: rectangular
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Colour Coding: grey
• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX

• Sensor Type: NTC Sensor
• Mounting Type: Clamped
• Connector Shape: D Shape
• Number of pins: 2
• for OE number: 06A919501
• Supplementary Article/Info 2: with mounting parts
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Number of pins: 2
• Guarantee: 3 years guarantee
• Weight [kg]: 0.01
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV703

• Vehicle Equipment: for vehicles with air conditioning
• Number of pins: 2
• Assy./disassy. by qualified personnel required!:
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Weight [g]: 15
• Name: IM 5309
• Manufacturer: ORIGINAL IMPERIUM

Manufacturer: METZGER

• Number of pins: 2
• Colour: black
• Material: Plastic
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Cable Length [mm]: 215
• Fabrication Number: ECP-AU-009
• Manufacturer: NTY

• Thread Size: 20 mm
• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: VER
• Additional information: WS2607
• Lisainfo: WS2607

• Number of pins: 2
• Connector Shape: rectangular
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• for OE number: 06A 919 501
• Manufacturer: TRUCKTEC

• Vehicle Identification Number (VIN) from: ******1P*6*000001
• Number of connectors: 2
• Colour: black
• Weight [kg]: 0.003
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: BWA
• Colour: grey
• for article number: 1.660.015K, 1.830.278K, 1.879.946
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS
• Additional information: 1-830-278
• Lisainfo: 1-830-278

• Engine Code: BWA
• Colour: grey
• for article number: 26.0015K, 7.3278K, 7.7946
• Manufacturer: FACET

• Supplementary Article/Info 2: with clamp holder
• Number of pins: 2
• Supplementary Article/Supplementary Info: with gasket/seal
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Thread Size: M20
• Number of pins: 2
• Housing Colour: grey
• Connector Shape: oval
• Manufacturer: ERA

• General Information: temperature sensor
• Manufacturer: VIKA

• Fabrication Number: ECT-VW-006
• Manufacturer: NTY
• Name: NTY ECT-VW-006

• Vehicle Identification Number (VIN) from: ******1P*6*000001
• Number of connectors: 2
• Colour: black
• Weight [kg]: 0.003
• Name: SW 33 10 2105
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• General Information: ambient air temperature sensor
• Manufacturer: BORSEHUNG

• Cable Length [mm]: 250
• Number of connectors: 3
• Housing Colour: grey
• Manufacturer: JP GROUP A/S
• Lisainfo: Sensor, crankshaft pulse
• Additional information: Sensor, crankshaft pulse

• Sensor Type: NTC Sensor
• Supplementary Article/Info 2: with seal ring
• Colour: black
• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MEY

• General Information: temperature sensor
• Manufacturer: VIKA

• Housing Colour: grey
• Number of pins: 2
• Spanner Size: 0
• Manufacturer: DELPHI
• Name: DE TS10278

• Housing Colour: black
• Number of pins: 2
• Name: ANDUR,VŽLISTEMPERATUUR
• Manufacturer: DLP
• Lisainfo: TS10266
• Additional information: TS10266

• Guarantee: 3 years guarantee
• Weight [kg]: 0.01
• Number of pins: 2
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV698

• Mounting Type: Plugged
• Voltage [V]: 12
• Supplementary Article/Supplementary Info: with gasket/seal
• Colour: black
• Sensor Type: NTC Sensor
• Number of pins: 2
• Supplementary Article/Info 2: with retaining ring
• Corresponds to the original part in colour: black, grey
• Fitting Depth [mm]: 20
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Number of pins: 2
• Weight [kg]: 0.3
• Packaging length [cm]: 12
• Packaging width [cm]: 8
• Packaging height [cm]: 6

• Number of pins: 2
• Colour Coding: grey
• Supplementary Article/Info 2: with seal ring
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Number of pins: 2
• Fitting Position: Air duct, to interior blower
• Housing Colour: grey
• Name: TEMPERATUURILšLITUS,KLIIMAVENTILAATOR
• Manufacturer: HAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Version: 2
• Connector Shape: D Shape
• Material: Plastic
• Number of pins: 2
• Plug Type: Female
• Sensor Type: NTC Sensor
• Spanner Size: 0
• Thread Size: 0
• Manufacturer: NISSENS

Technical Information: FIRST FIT - a time-saving installation! Find all additional parts such as O-rings, clip, washer in the box.

• Number of connectors: 2
• Colour Coding: grey
• Screw length below head [mm]: 20
• Weight [kg]: 0.03
• Supplementary Article/Supplementary Info: with gasket/seal, with retaining spring
• Name: SW 30 92 9318
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Sensor Type: Passive sensor
• Number of pins: 3
• Voltage [V]: 12
• Name: ANDUR, VŽNTVOLL
• Manufacturer: MAX

• Colour Coding: grey
• Corresponds to the original part in colour: black
• Number of pins: 2
• Supplementary Article/Supplementary Info: with gasket/seal
• Version: IAM
• Article number of recommended accessories: 0899250, 0905513
• Power [W]: 0.06
• Manufacturer: METZGER

• Cable Length [mm]: 215
• Number of pins: 3
• Sensor Type: Inductive Sensor
• Assy./disassy. by qualified personnel required!:
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Number of pins: 2
• Manufacturer: FAE

• Number of pins: 2
• Colour: black
• Manufacturer: METZGER

• Voltage [V]: 12
• Length [mm]: 220
• Number of pins: 3
• Guarantee: 3 years guarantee
• Weight [kg]: 0.1
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV266

• Connector Shape: D Shape
• Supplementary Article/Info 2: without cable
• Colour: black
• Number of pins: 2
• Fitting Position: Front
• Vehicle Equipment: for vehicles with air conditioning
• Power [W]: 0.06
• Manufacturer: METZGER

• Construction Year to: 03.2009
• Diameter [mm]: 25
• Height [mm]: 52
• Number of connectors: 2
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Diameter [mm]: 26
• Number of pins: 2
• Supplementary Article/Info 2: with seal ring
• Spring Design: Retaining Spring
• Length [mm]: 20
• Housing Colour: blue
• Height [mm]: 57
• Colour: grey
• Number of connectors: 2
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Plug housing design: Plug sleeve housing
• Manufacturer Restriction: VAG
• Cable Length [mm]: 500
• Number of pins: 2
• Supplementary Article/Info 2: with pipe
• Cable Cross Section [mm²]: 0.75
• Socket Width [mm]: 1.5
• Temperature range from [°C]: -25
• Temperature range to [°C]: +140
• Cable insulation material: Silicone
• Current carrying capacity [A]: 9
• Operating voltage [V]: 24
• for OE number: 1J6 943 021 B, 1JE 943 021, 1K8 943 021 C
• for article number: 70660022
• SVHC: No SVHC present!
• Name: Kaabli remondikomplekt,
• Manufacturer: HBE

Supplementary Article/Supplementary Info: with socket housing, with gaskets/seals, with heat shrink tubing

• Number of pins: 2
• Connector Shape: rectangular
• Supplementary Article/Info 2: without cable
• Vehicle Equipment: for vehicles with automatic climate control
• for OE number: 1K0907543G
• Manufacturer: MEAT&DORIA

• Length [mm]: 36
• Width [mm]: 17
• Height [mm]: 13
• Vehicle Equipment: for vehicles with air conditioning
• Number of pins: 2
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Connector Shape: D Shape
• Number of pins: 3
• Supplementary Article/Info 2: with cable
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Construction Year to: 03.2009
• Sensor Type: Inductive Sensor
• Number of pins: 3
• Voltage [V]: 12
• Connector Shape: D Shape
• Supplementary Article/Info 2: with cable
• Resistor [Ohm]: 900
• Manufacturer: VALEO
• Name: VA 254019

• Resistor [Ohm]: 900
• Colour: black
• Cable Length [mm]: 190
• Number of pins: 3
• Fitting Depth [mm]: 24
• Weight [kg]: 0.06
• Manufacturer: ERA

• Fitting Depth [mm]: 52
• Supplementary Article/Supplementary Info: with gasket/seal
• Number of pins: 3
• Fabrication Number: EPO-AU-001
• Manufacturer: NTY
• Name: NTY EPO-AU-001

• General Information: interior temperature sensor
• Manufacturer: BORSEHUNG

• Sensor Type: Inductive Sensor
• Cable Length [mm]: 191
• Number of pins: 3
• Name: ANDUR, VŽNTVOLL
• Manufacturer: MEY

• Supplementary Article/Supplementary Info: with gasket/seal
• Number of pins: 3
• Assy./disassy. by qualified personnel required!:
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Cable Length [mm]: 270
• Number of pins: 3
• Name: ANDUR, VŽNTVOLL
• Manufacturer: DLP

Additional information: "Tootja: DELPHI
A3 (8L1), 09.96-05.0
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
A3 (8L1), 09.96-05.0
(kvaliteediklass: PJ)"

• Vehicle Identification Number (VIN) from: 5P-7-000 001
• Number of pins: 2
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: BWA
• Length [mm]: 215
• Name: ANDUR, VŽNTVOLL
• Manufacturer: EPS

• Engine Code: BWA
• Length [mm]: 215
• Manufacturer: FACET

• Transmission Type: Dual-Clutch Transmission
• for PR number: G0R
• Length [mm]: 215
• Supplementary Article/Supplementary Info: with temperature sensor
• for OE number: 02E 927 321 C
• Number of pins: 4
• Name: Andur, v„ntvoll
• Manufacturer: MAX

• Length [mm]: 250
• Number of connectors: 3
• Weight [kg]: 0.06
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.