• Fitting Position: Front Axle Right, Front Axle Left
• Required quantity: 1
• Block Separation:
• Control/Trailing Arm Type: Control Arm
• for article number: 58011902 / 58012001
• Guarantee: 3 years guarantee or up to 75,000km
• Manufacturer: METZGER

• Fitting Position: Front Axle Right, Front Axle Left
• Required quantity: 1
• Control/Trailing Arm Type: Control Arm
• for article number: 58011902 / 58012001
• Guarantee: 3 years guarantee or up to 75,000km
• Manufacturer: METZGER

• Fitting Position: Front Axle Right, Front Axle Left
• replacement in pairs recommended:
• Required quantity: 2
• Name: Remondikomplekt,ootshoob
• Manufacturer: MEY
• Lisainfo: 1006100061
• Additional information: 1006100061

• Fitting Position: Front Axle Left
• Control/Trailing Arm Type: for control arm
• Supplementary Article/Info 2: with rubber mount, with ball joint
• reinforced version:
• Replace in pairs only:
• with environmental seal: Carbon Neutral
• Required quantity: 1
• paired article number: 116 610 0000/HD
• Name: Remondikomplekt,ootshoob
• Manufacturer: MEY

General Information: 4-year warranty on all MEYLE-HD parts. Engineered and quality approved in Germany.

• Fitting Position: Front Axle Right
• Control/Trailing Arm Type: for control arm
• Supplementary Article/Info 2: with ball joint, with rubber mount
• reinforced version:
• Replace in pairs only:
• with environmental seal: Carbon Neutral
• Required quantity: 1
• paired article number: 116 610 0001/HD
• Name: Remondikomplekt,ootshoob
• Manufacturer: MEY

General Information: 4-year warranty on all MEYLE-HD parts. Engineered and quality approved in Germany.

• Fitting Position: Front Axle Left
• Axle alignment required after fitting:
• paired article number: V10-3908
• for OE number: 1J0 407 151 C
• Control/Trailing Arm Type: for control arm
• Quantity Unit: Set
• Supplementary Article/Supplementary Info: with accessories
• Weight [kg]: 0.84
• Manufacturer: VAICO

Supplementary Article/Info 2: with rubber mount, with ball joint, with lock screw set General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Left, Front Axle Right
• Material: Sheet Steel
• Supplementary Article/Info 2: with bearing
• Manufacturer: MERTZ

• Fitting Position: Rear Axle Left, Rear Axle Right
• Control/Trailing Arm Type: Control Arm
• Length [mm]: 520
• Material: Sheet Steel
• Weight [kg]: 1.08
• Name: DY 26-21720
• Manufacturer: DYS

• Axle alignment required after fitting:
• paired article number: V10-3907
• Control/Trailing Arm Type: for control arm
• Supplementary Article/Supplementary Info: with accessories
• Fitting Position: Front Axle Right
• Quantity Unit: Set
• Weight [kg]: 0.841
• Manufacturer: VAICO

Supplementary Article/Info 2: with rubber mount, with ball joint, with lock screw set General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Control/Trailing Arm Type: Control Arm
• Control/Trailing Arm Design: Triangular Control Arm
• Fitting Position: Front Axle Left, Front Axle Right
• Material: Sheet Steel
• Supplementary Article/Supplementary Info: with rubber-metal mounts
• Supplementary Article/Info 2: without ball joint
• Surface: Cathodic Painting, Black-painted
• Also available as set:
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle, both sides, Lower
• Manufacturer: DENCKERMANN ZAWIESZENIE

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle, both sides
• Material: Sheet Steel
• Manufacturer: MAX

Name: Roolimine - K„„ndmik VW P. GOLF 4/A3 LE/PR BEZ SWORZNIA

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Right, Lower
• paired article number: 72-3785
• Material: Sheet Steel
• Supplementary Article/Info 2: with nut, with bearing, with ball joint
• Name: Ootshoob, k„„ndmik
• Manufacturer: MAX
• Lisainfo: MGZ-101124
• Additional information: MGZ-101124

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Left, Lower
• paired article number: 72-3794
• Material: Sheet Steel
• Supplementary Article/Info 2: with bearing, with nut, with ball joint
• Name: Ootshoob, k„„ndmik
• Manufacturer: MAX
• Lisainfo: MGZ-101115
• Additional information: MGZ-101115

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Lower, Front Axle Left, Front Axle Right
• Material: Sheet Steel
• Name: Control arm left=right
• Quality class: PJ

Lisainfo: "Tootja: SRL
AUDI A3 96-99
(kvaliteediklass: PJ)" Additional information: "Tootja: SRL
AUDI A3 96-99
(kvaliteediklass: PJ)"

• Fitting Position: Front Axle Left, Front Axle Right, Lower
• Control/Trailing Arm Type: Control Arm
• Manufacturer: JP GROUP
• Lisainfo: Wishbone, front
• Additional information: Wishbone, front

• Fitting Position: Lower, Front Axle Left, Front Axle Right
• Control/Trailing Arm Type: Control Arm
• Manufacturer: GSP

• Fitting Position: Front Axle Right, Lower
• paired article number: 5014717
• Control/Trailing Arm Type: Control Arm
• Net weight [kg]: 3.55
• Manufacturer: NK

Name: Roolimine - K„„ndmik VW P. A3/GOLF4/BORA PR KPL.ZE SWORZNIEM

• Fitting Position: Front Axle Left, Lower
• paired article number: 5014718
• Control/Trailing Arm Type: Control Arm
• Net weight [kg]: 3.57
• Manufacturer: NK

Name: Roolimine - K„„ndmik VW P. A3/GOLF4/BORA LE KPL.ZE SWORZNIEM

• Fitting Position: Front Axle Right, Lower
• Control/Trailing Arm Type: Control Arm
• Cone Size [mm]: 18
• Manufacturer: DELLO AUTOMEGA

• Fitting Position: Front Axle, outer, Left, Right, Lower
• Material: Sheet Steel
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: without ball joint
• Length [mm]: 420
• Width [mm]: 390
• Height [mm]: 55
• Manufacturer: DELPHI
• Name: DE TC2010

• Fitting Position: Front Axle Right, Lower Front Axle
• Length [mm]: 276
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: with ball joint
• Inner Diameter 1 [mm]: 12
• paired article number: TRC0123
• Manufacturer: BGA

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle
• Inner Diameter [mm]: 12
• Name: ALT 79463AL
• Manufacturer: ALTE AUTOMOTIVE

• Fitting Position: Front Axle, both sides
• Control/Trailing Arm Type: Control Arm
• Name: COC 49398710
• Manufacturer: CORTECO

• Construction Year to: 12.2004
• Fitting Position: Front Axle Left, Lower
• for OE number: 1J0407151A
• Required quantity: 1
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: with ball joint
• Manufacturer: FAI

• Construction Year to: 12.2004
• Fitting Position: Front Axle Right, Lower
• for OE number: 1J0407151B
• Required quantity: 1
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: with ball joint
• Manufacturer: FAI

• Fitting Position: Front Axle Right, Lower
• Control/Trailing Arm Type: Control Arm
• Manufacturer: JP GROUP
• Lisainfo: Track Control Arm
• Additional information: Track Control Arm

• Fitting Position: Front Axle Left, Lower
• Control/Trailing Arm Type: Control Arm
• Lisainfo: Track Control Arm
• Additional information: Track Control Arm

• Fitting Position: Lower, Front Axle both sides
• Required quantity: 2
• Control/Trailing Arm Design: Triangular Control Arm
• paired article number: VKDS 321004
• Hole Spacing 1/Hole Spacing 2: 276,4
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: without ball joint
• Manufacturer: SKF
• Name: SK VKDS321004

• Fitting Position: Front Axle Left, Lower
• Control/Trailing Arm Type: Control Arm
• Cone Size [mm]: 15
• paired article number: 9050143
• Manufacturer: KAMOKA

• Fitting Position: Front Axle Left, Lower
• Control/Trailing Arm Type: Control Arm
• Material: Sheet Steel
• paired article number: 20-01071-1
• Weight [kg]: 3.49
• Name: DY 20-01071-2
• Manufacturer: DYS

• Fitting Position: Front Axle Right, Lower
• Control/Trailing Arm Type: Control Arm
• Material: Sheet Steel
• paired article number: 20-01071-2
• Weight [kg]: 3.49
• Name: DY 20-01071-1
• Manufacturer: DYS

• Control/Trailing Arm Type: Control Arm
• Colour: black
• Weight [kg]: 3.5
• Fitting Position: Front Axle Right, Lower
• Required quantity: 1
• Material: Sheet Steel
• Supplementary Article/Info 2: with rubber sleeves
• Manufacturer: VIKA

General Information: Wishbone arm with bush for lower control;with big and small rubber bush

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Left, Front Axle Right, Lower, outer
• Manufacturer: TRW

SVHC: No information available, please contact the manufacturer!

• Name: Control arm left=right
• Quality class: PJ

Lisainfo: "Tootja: TEKNOROT
A.A3/GOLFIV/OCT/TOL.
(kvaliteediklass: PJ)"

• Fitting Position: Front Axle Right, Lower
• Control/Trailing Arm Type: Control Arm
• Cone Size [mm]: 15
• paired article number: 9050142
• Manufacturer: KAMOKA

• Fitting Position: Front Axle Left, Lower
• Material: Sheet Steel
• paired article number: TC787
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: with ball joint
• Length [mm]: 466
• Width [mm]: 156
• Manufacturer: DELPHI
• Name: DE TC786

• Fitting Position: Front Axle Right, Lower
• Material: Sheet Steel
• paired article number: TC786
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: with ball joint
• Length [mm]: 466
• Width [mm]: 156
• Manufacturer: DELPHI

• Trim Level: CGLC
• for OE number: 1J0407151C
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Lower Front Axle
• Name: DA DSS1087
• Manufacturer: DAYCO

• paired article number: 19820
• Material: Sheet Steel
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Right, Lower
• Weight [kg]: 3.5
• Supplementary Article/Info 2: with ball joint
• Supplementary Article/Supplementary Info: with lock nut, with rubber mounts
• Observe service information:
• Manufacturer: FEBI

Technical Information: Please tighten the mounting bolts with the wheels on the ground. General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Front Axle Left, outer, Lower
• Cone Size [mm]: 14.9
• Supplementary Article/Info 2: with ball joint, with rubber mount
• Material: Steel
• Length [mm]: 391
• Control/Trailing Arm Type: Control Arm
• as standard:
• Thread Size: M12X1,5 RHT
• paired article number: 210042
• Weight [kg]: 3.494
• Installation Information: Important: Observe Fitting Instructions
• Manufacturer: A.B.S.

• Fitting Position: Front Axle Left, Lower
• Control/Trailing Arm Type: Control Arm
• Manufacturer: OYODO

• Fitting Position: Front Axle Right, Lower
• Control/Trailing Arm Type: Control Arm
• Manufacturer: OYODO

• Fitting Position: Front Axle Right, Front Axle Left, Lower
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: with rubber mount
• Material: Sheet Steel
• replacement in pairs recommended:
• Required quantity: 2
• Manufacturer: MEY

Name: Roolimine - K„„ndmik VW P. GOLF 4/A3 LE/PR BEZ SWORZNIA

• Fitting Position: Rear Axle
• Control/Trailing Arm Type: Control Arm
• Length [mm]: 556
• Name: Ootshoob, k„„ndmik
• Manufacturer: MAG

• Material: Sheet Steel
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Left, Lower, Front Axle Right
• Weight [kg]: 3.037
• Supplementary Article/Info 2: without ball joint
• Supplementary Article/Supplementary Info: with rubber mounts
• Observe service information:
• Manufacturer: FEB

Technical Information: Please tighten the mounting bolts with the wheels on the ground. General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. Name: Roolimine - K„„ndmik VW P. GOLF 4/A3 LE/PR BEZ SWORZNIA

• paired article number: 19822
• Material: Sheet Steel
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Left, Lower
• Weight [kg]: 3.5
• Supplementary Article/Info 2: with ball joint
• Supplementary Article/Supplementary Info: with lock nut, with rubber mounts
• Observe service information:
• Name:
• Manufacturer: FEB

Technical Information: Please tighten the mounting bolts with the wheels on the ground. General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Front Axle Right, outer, Lower
• Cone Size [mm]: 14.9
• Supplementary Article/Info 2: with ball joint, with rubber mount
• Material: Steel
• Length [mm]: 391
• Control/Trailing Arm Type: Control Arm
• as standard:
• Thread Size: M12X1,5 RHT
• paired article number: 210043
• Weight [kg]: 3.486
• Installation Information: Important: Observe Fitting Instructions
• Manufacturer: A.B.S.

• Fitting Position: Front Axle
• Control/Trailing Arm Type: Control Arm
• Material: Sheet Steel
• Supplementary Article/Info 2: without ball joint
• SVHC: No SVHC present!
• Manufacturer: FAG
• Name: LU 821034910

• Fitting Position: Lower, Front Axle Right
• Control/Trailing Arm Design: Triangular Control Arm
• paired article number: VKDS 321102 B
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Supplementary Info: with synthetic grease
• Supplementary Article/Info 2: with ball joint
• Manufacturer: SKF
• Name: SK VKDS321103B

• Fitting Position: Lower, Front Axle Left
• Control/Trailing Arm Design: Triangular Control Arm
• paired article number: VKDS 321103 B
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Supplementary Info: with synthetic grease
• Supplementary Article/Info 2: with ball joint
• Manufacturer: SKF
• Name: SK VKDS321102B

• Control/Trailing Arm Type: Control Arm
• Base body material: Steel
• Fitting Position: Front Axle Right
• Net weight [kg]: 2,925
• Diameter [mm]: 12.5
• paired article number: G40.3599/C
• Diameter 1 [mm]: 12.5
• Supplementary Article/Info 2: with ball joint
• Name: OMG G40.3598/C
• Manufacturer: OMG

• paired article number: 30 91 9820
• Material: Sheet Steel
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Right, Lower
• Weight [kg]: 3.5
• Supplementary Article/Supplementary Info: with rubber mounts, with lock nut
• Supplementary Article/Info 2: with ball joint
• Name: SW 30 91 9822
• Manufacturer: SWAG

Technical Information: Please tighten the mounting bolts with the wheels on the ground. General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• paired article number: 30 91 9822
• Material: Sheet Steel
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Left, Lower
• Weight [kg]: 3.5
• Supplementary Article/Info 2: with ball joint
• Supplementary Article/Supplementary Info: with rubber mounts, with lock nut
• Name: SW 30 91 9820
• Manufacturer: SWAG

Technical Information: Please tighten the mounting bolts with the wheels on the ground. General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Lower, Front Axle Right
• paired article number: S060339
• Cone Size [mm]: 14.9
• Control/Trailing Arm Type: Control Arm
• Thread Size 1: M12×1,5
• Manufacturer: GSP

• Control/Trailing Arm Type: Control Arm
• Steering: with tie rod ends
• Fitting Position: Front Axle Left
• Manufacturer: VIKA

General Information: Wishbone arm assembly for lower control;front left; with ball

• Fitting Position: Lower, Front Axle Left
• paired article number: S060340
• Cone Size [mm]: 14.9
• Control/Trailing Arm Type: Control Arm
• Thread Size 1: M12×1,5
• Manufacturer: GSP

• Control/Trailing Arm Type: Control Arm
• Quantity Unit: Set
• Fitting Position: Lower, Front Axle Left
• Material: Sheet Steel
• Quality class: PJ
• Name: Control arm left

Lisainfo: "Tootja: SRL
AUDI A3 96-99
(kvaliteediklass: PJ)" Additional information: "Tootja: SRL
AUDI A3 96-99
(kvaliteediklass: PJ)"

• Control/Trailing Arm Type: Control Arm
• Quantity Unit: Set
• Fitting Position: Lower, Front Axle Right
• Material: Sheet Steel
• Quality class: PJ
• Name: Control arm right

Lisainfo: "Tootja: SRL
AUDI A3 96-99
(kvaliteediklass: PJ)" Additional information: "Tootja: SRL
AUDI A3 96-99
(kvaliteediklass: PJ)"

• Control/Trailing Arm Type: Control Arm
• Steering: with tie rod ends
• Fitting Position: Front Axle Right
• Manufacturer: VIKA

General Information: Wishbone arm assembly for lower control;front right; with ball

• Quantity per packing unit: 8
• Fitting Position: Front Axle
• Manufacturer: DELPHI
• Name: DE TC1970KIT

• Fitting Position: Front Axle, Left, Right, outer, Lower
• Weight [kg]: 3
• Required quantity: 2
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: with rubber mount, without ball joint
• Packaging length [cm]: 46
• Packaging width [cm]: 37
• Packaging height [cm]: 6
• Manufacturer: MONROE

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle, Right
• Material: Steel
• Supplementary Article/Info 2: with bolts
• paired article number: FT15534
• Manufacturer: FAST

• Fitting Position: Front Axle Right
• Control/Trailing Arm Type: Control Arm
• Material: Sheet Steel
• paired article number: 49399127
• Name: COC 49399071
• Manufacturer: CORTECO

• Fitting Position: Front Axle Left
• Control/Trailing Arm Type: Control Arm
• Material: Sheet Steel
• paired article number: 49399071
• Name: COC 49399127
• Manufacturer: CORTECO

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle, Left
• Material: Steel
• Supplementary Article/Info 2: with bolts
• paired article number: FT15535
• Manufacturer: FAST

• Material: Sheet Steel
• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Left, Lower, Front Axle Right
• Weight [kg]: 3.037
• Supplementary Article/Info 2: without ball joint
• Supplementary Article/Supplementary Info: with rubber mounts
• Name: SW 32 73 0016
• Manufacturer: SWAG

Technical Information: Please tighten the mounting bolts with the wheels on the ground. General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Control/Trailing Arm Type: not for control arm
• Manufacturer: SKF
• Name: SK VKDS461000

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Left, Lower
• Length [mm]: 465
• Thread Size: M12 x 1,5
• Cone Size [mm]: 18
• paired article number: 79507AL
• Name: ALT 79512AL
• Manufacturer: ALTE AUTOMOTIVE

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Right, Lower
• Length [mm]: 465
• Thread Size: M12 x 1,5
• Cone Size [mm]: 18
• paired article number: 79512AL
• Name: ALT 79507AL
• Manufacturer: ALTE AUTOMOTIVE

• Fitting Position: Front Axle
• Control/Trailing Arm Type: Control Arm
• Weight [kg]: 1.84
• Name: DY 29-23959
• Manufacturer: DYS

• Name: Control arm right
• Quality class: PJ

Lisainfo: "Tootja: TEKNOROT
A.A3/GOLFIV/OCT/TOL.
(kvaliteediklass: PJ)"

• Name: Control arm left
• Quality class: PJ

Lisainfo: "Tootja: TEKNOROT
A.A3/GOLFIV/OCT/TOL.
(kvaliteediklass: PJ)"

• Fitting Position: Front Axle
• Control/Trailing Arm Type: Control Arm
• Weight [kg]: 1.83
• Name: DY 29-23736
• Manufacturer: DYS

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle, both sides
• Material: Sheet Steel
• Article number of recommended accessories: 44091 01
• Manufacturer: LMI

SVHC: No information available, please contact the manufacturer! Name: Roolimine - K„„ndmik VW P. GOLF 4/A3 LE/PR BEZ SWORZNIA

• Fitting Position: Front Axle Right
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: with ball joint
• Material: Sheet Steel
• Thread Size: M12x1,5
• Length [mm]: 347
• Replace in pairs only:
• reinforced version:
• Width [mm]: 277
• with environmental seal: Carbon Neutral
• Required quantity: 1
• paired article number: 116 050 0009/HD
• Manufacturer: MEY

General Information: Improved performance and service life: larger ball pin life: larger ball pin diameter of MEYLE-HD ball joint distributes forces over a larger surface area and minimizes part wear. Name: Roolimine - K„„ndmik VW P. A3/GOLF4/BORA PR KPL.ZE SWORZNIEM

• Fitting Position: Front Axle Left
• Control/Trailing Arm Type: Control Arm
• Supplementary Article/Info 2: with ball joint
• Material: Sheet Steel
• Thread Size: M12x1,5
• Length [mm]: 347
• Replace in pairs only:
• reinforced version:
• Width [mm]: 277
• with environmental seal: Carbon Neutral
• Required quantity: 1
• paired article number: 116 050 0010/HD
• Manufacturer: MEY

General Information: Improved performance and service life: larger ball pin life: larger ball pin diameter of MEYLE-HD ball joint distributes forces over a larger surface area and minimizes part wear. Name: Roolimine - K„„ndmik VW P. A3/GOLF4/BORA LE KPL.ZE SWORZNIEM

• Control/Trailing Arm Type: Control Arm
• Fitting Position: Front Axle Left, Lower
• External Thread 2 [mm]: M12x1,5
• Weight [kg]: 3.56
• Manufacturer: RTS