• Oxygen Sensor: Diagnostic Probe
• Number of circuits: 4
• Overall Length [mm]: 750
• Manufacturer: JP GROUP A/S
• Lisainfo: Lambda sensor
• Additional information: Lambda sensor

• External Thread [mm]: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 510
• Oxygen Sensor: Planar probe
• Manufacturer: JP GROUP
• Lisainfo: Lambda sensor
• Additional information: Lambda sensor

• External Thread [mm]: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 620
• Oxygen Sensor: Heated
• Manufacturer: JP GROUP
• Lisainfo: Lambda sensor
• Additional information: Lambda sensor

• External Thread [mm]: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 480
• Oxygen Sensor: Planar probe
• Manufacturer: JP GROUP
• Lisainfo: Lambda sensor
• Additional information: Lambda sensor

• Oxygen Sensor: Diagnostic Probe, Thread pre-greased
• Fitting Position: after catalytic converter
• Fabrication Number: ESL-AU-007
• Manufacturer: NTY
• Name: NTY ESL-AU-007

• Oxygen Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Oxygen Sensor: Regulating Probe
• Number of circuits: 4
• Manufacturer: KAMOKA

• Oxygen Sensor: Diagnostic Probe, Heated
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 750
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Fitting Position: after catalytic converter
• Number of pins: 4
• Rated Voltage [V]: 12
• Oxygen Sensor: Planar probe, Heated
• Connector Shape: D Shape
• Cable Length [mm]: 730
• Overall Length [mm]: 757
• Spanner Size: 22
• Thread Size: M 18
• Thread Pitch [mm]: 1.5
• Supplementary Article/Supplementary Info: with cable tie
• Lubrication: with grease lubrication
• Full Set:
• Manufacturer: TOPRAN HANS PRIES

Supplementary Article/Info 2: with plastic socket, with heat shield pipe, with mounting manual General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Oxygen Sensor: Diagnostic Probe
• Fitting Position: Front
• Length [mm]: 940
• Number of connectors: 4
• Manufacturer: VERNET

• Oxygen Sensor: Diagnostic Probe, Heated
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: MAX
• Lisainfo: MGS-615
• Additional information: MGS-615

• Construction Year to: 10.2009
• Fitting Position: Front, after catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Cable Length [mm]: 720
• Oxygen Sensor: Diagnostic Probe, Thread pre-greased
• Number of circuits: 4
• Weight [kg]: 0.156
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: AXP
• Oxygen Sensor: Unheated
• Number of pins: 4
• Cable Length [mm]: 630
• Quality: OE EQUIVALENT
• for OE number: 06A906262AS
• Manufacturer: MEAT&DORIA

• Resistor [Ohm]: 9
• Length [mm]: 721
• Number of circuits: 4
• Conductor Number: 4
• Cable Length [mm]: 721
• Oxygen Sensor: Heated
• Name: LAMBDA ANDUR
• Manufacturer: MAG

• Oxygen Sensor: Oxygen Sensor
• Cable Length [mm]: 760
• Alternatively:
• Number of circuits: 4
• Alternative Repair Kit: 570030
• Manufacturer: ERA

• Oxygen Sensor: Diagnostic Probe, Planar probe, Heated
• Block Separation:
• Construction Year from: 11.2009
• Fitting Position: after catalytic converter
• Cable Length [mm]: 700
• Name: LAMBDA ANDUR
• Manufacturer: DLP
• Quality class: PJ

Additional information: "Tootja: DELPHI
BORA (1J2), 10.98-09
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
BORA (1J2), 10.98-09
(kvaliteediklass: PJ)"

• Oxygen Sensor: Diagnostic Probe, Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 580
• Weight [kg]: 0.097
• for OE number: 06A 906 262 AH
• Name: SW 33 10 3202
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Oxygen Sensor: Diagnostic Probe
• Length [mm]: 550
• Technical Information Number: Universal 77015
• Manufacturer: FAE

• Oxygen Sensor: Diagnostic Probe
• Voltage [V]: 12
• Length [mm]: 760
• Guarantee: 3 years guarantee
• Number of circuits: 4
• Weight [kg]: 0.15
• Resistor [Ohm]: 9
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV694
• Manufacturer: ESEN SKV

• Construction Year from: 11.2009
• Oxygen Sensor: Diagnostic Probe, Planar probe, Heated
• Fitting Position: after catalytic converter
• Cable Length [mm]: 740
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Oxygen Sensor: Diagnostic Probe
• Voltage [V]: 12
• Length [mm]: 650
• Guarantee: 3 years guarantee
• Number of circuits: 4
• Weight [kg]: 0.15
• Resistor [Ohm]: 6
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV706
• Manufacturer: ESEN SKV

• Oxygen Sensor: Regulating Probe, Thread pre-greased
• Number of circuits: 5
• Fitting Position: before catalytic converter
• Fabrication Number: ESL-AU-002
• Manufacturer: NTY
• Name: NTY ESL-AU-002

• Engine Code: AXP, BCA
• Line insulation design: with silicone-coated woven-fibre insulation
• Supplementary Article/Info 2: without plug
• Number of pins: 4
• for OE number: V99760001
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Length [mm]: 350
• Fitting Position: after catalytic converter
• Manufacturer: VEMO GERMANY

Oxygen Sensor: Diagnostic Probe, Finger probe, Heated, Thread pre-greased General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Oxygen Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Construction Year from: 08.2001
• Engine Code: AXP
• Fitting Position: after catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Oxygen Sensor: Planar probe, Heated, Thread pre-greased
• Supplementary Article/Info 2: without plug
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 01.2002
• Engine Code: AXP
• Line insulation design: with silicone-coated woven-fibre insulation
• Conductor Number: 4
• Connector Shape: D Shape
• Cable Length [mm]: 225
• Thread Size: M18 x 1,5
• Length [mm]: 350
• Number of pins: 4
• Version: ZR-PLANAR
• Weight [kg]: 0.129
• Oxygen Sensor: Thread pre-greased
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 10.2009
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 93
• Gross Weight [g]: 140
• Manufacturer: DENSO
• Name: DN DOX-0150
• Quality class: Q

Oxygen Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased, Oxygen Sensor Additional information: "Tootja: DENSO
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
(kvaliteediklass: Q)"

• Engine Code: AXP
• Line insulation design: with silicone-coated woven-fibre insulation
• Overall Length [mm]: 1,800
• Number of pins: 4
• Recommended change interval [km]: 160,000
• Weight [kg]: 0.166
• Oxygen Sensor: Thread pre-greased
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 5
• Overall Length [mm]: 1,510
• Oxygen Sensor: Regulating Probe
• Manufacturer: JP GROUP A/S
• Lisainfo: Lambda Sensor
• Additional information: Lambda Sensor

• Engine Code: BCA
• Construction Year from: 11.2009
• Fitting Position: before soot particulate filter
• Oxygen Sensor: Heated
• Length [mm]: 645
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 740
• Weight [kg]: 0.095
• Name: SW 30 93 4388
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Construction Year to: 01.2002
• Engine Code: AXP
• Line insulation design: with silicone-coated woven-fibre insulation
• Weight [kg]: 0.122
• Socket colour: brown
• Connector Shape: D Shape
• Thread Size: M18 x 1,5
• Length [mm]: 570
• for OE number: 06A 906 262 F
• Cable Length [mm]: 570
• Number of pins: 4
• Oxygen Sensor: Diagnostic Probe, Thread pre-greased
• Number of circuits: 4
• Fitting Position: after catalytic converter
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 10.2009
• for OE number: 036906262H, 022906262BG
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 650
• Number of pins: 4
• Weight [g]: 189
• Gross Weight [g]: 222
• Manufacturer: DENSO
• Name: DN DOX-2000
• Quality class: Q

Oxygen Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased, Oxygen Sensor Additional information: "Tootja: DENSO
POLO SEDAN, 09.02-
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
POLO SEDAN, 09.02-
(kvaliteediklass: Q)"

• Oxygen Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Length [mm]: 1,500
• Number of pins: 6
• Manufacturer: FAE

• Construction Year from: 11.2009
• Oxygen Sensor: Diagnostic Probe, Planar probe
• Fitting Position: after catalytic converter
• Cable Length [mm]: 750
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PA358066401

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Fitting Position: before catalytic converter
• Rated Voltage [V]: 12
• Number of pins: 6
• Connector Shape: oval
• Cable Length [mm]: 1,510
• Overall Length [mm]: 1,538
• Spanner Size: 22
• Thread Size: M 18
• Thread Pitch [mm]: 1.5
• Supplementary Article/Supplementary Info: with cable tie
• Supplementary Article/Info 2: with plastic socket, with heat shield pipe
• Lubrication: with grease lubrication
• Full Set:
• Manufacturer: TOPRAN

Oxygen Sensor: Regulating Probe, Broadband oxygen sensor, Heated, Planar probe General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Oxygen Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 760
• Available as universal article as well, see article no.: 0258986615
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Number of circuits: 5
• Length [mm]: 1,510
• Conductor Number: 5
• Cable Length [mm]: 1,510
• Oxygen Sensor: Heated
• Name: LAMBDA ANDUR
• Manufacturer: MAG

• Construction Year to: 01.2002
• Engine Code: AXP
• Fitting Position: before catalytic converter
• Oxygen Sensor: Planar probe, Thread pre-greased, Heated
• Number of pins: 4
• Cable Length [mm]: 720
• Thread Size: M18x1,5
• Switch Pressure [bar]: 4
• Connector Shape: oval
• Manufacturer: VALEO
• Name: VA 368041

• Engine Code: AXP
• Oxygen Sensor: Regulating Probe, Heated
• Fitting Position: before catalytic converter
• Number of circuits: 5
• Length [mm]: 1,500
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Oxygen Sensor: Regulating Probe, Oxygen Sensor, Heated
• Fitting Position: before catalytic converter
• Quantity: 1
• Cable Length [mm]: 950
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Oxygen Sensor: Oxygen Sensor
• Voltage [V]: 12
• Colour: red
• Guarantee: 3 years guarantee
• Number of circuits: 5
• Weight [kg]: 0.15
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV905
• Manufacturer: ESEN SKV

• Construction Year to: 01.2002
• Transmission Type: Manual Transmission
• Engine Code: AXP
• Oxygen Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Length [mm]: 650
• Number of circuits: 4
• Manufacturer: VDO

• Construction Year from: 10.2009
• Oxygen Sensor: Diagnostic Probe, Heated
• Voltage [V]: 12
• Conductor Number: 4
• Cable Length [mm]: 940
• Manufacturer: PIERBURG

• Construction Year to: 09.2004
• Oxygen Sensor: Oxygen Sensor
• Voltage [V]: 12
• Length [mm]: 1,510
• Guarantee: 3 years guarantee
• Number of circuits: 5
• Weight [kg]: 0.22
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV852
• Manufacturer: ESEN SKV

• Construction Year from: 06.2004
• Exhaust System: for pre-catalytic converter
• Engine Code: BCA
• Cable Length [mm]: 340
• Oxygen Sensor: Oxygen Sensor, Heated
• Manufacturer: DELPHI
• Name: DE ES11015-12B1

• Oxygen Sensor: Oxygen Sensor
• Voltage [V]: 12
• Length [mm]: 400
• Guarantee: 3 years guarantee
• Number of circuits: 5
• Weight [kg]: 0.15
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV871
• Manufacturer: ESEN SKV

• Construction Year to: 09.2004
• Oxygen Sensor: Oxygen Sensor
• Voltage [V]: 12
• Length [mm]: 1,470
• Guarantee: 3 years guarantee
• Number of circuits: 5
• Weight [kg]: 0.22
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV860
• Manufacturer: ESEN SKV

• Oxygen Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 5
• Overall Length [mm]: 760
• Recommended change interval [km]: 160,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Oxygen Sensor: Oxygen Sensor
• Guarantee: 3 years guarantee
• Weight [kg]: 0.16
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV911

• Oxygen Sensor: Heated
• Conductor Number: 5
• General Information: lambda probe; 5 wire
• Manufacturer: VIKA

• Oxygen Sensor: Regulating Probe, Oxygen Sensor
• Exhaust System: before catalytic converter
• Voltage [V]: 12
• Guarantee: 3 years guarantee
• Weight [kg]: 0.16
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV907

• Oxygen Sensor: Oxygen Sensor
• Guarantee: 3 years guarantee
• Weight [kg]: 0.15
• Always compare old and new part (in particular OE No.):
• Technical Information: Universal
• Name: CE 09SKV915
• Manufacturer: ESEN SKV

• Fitting Position: before catalytic converter
• Required quantity: 1
• Oxygen Sensor: Regulating Probe
• Cable Length [mm]: 1,500
• Number of pins: 6
• Exhaust System: before catalytic converter
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead
• Manufacturer: HELLA
• Name: HE 6PA009166821

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Fitting Position: Front
• Quantity: 1
• Line insulation design: with silicone-coated woven-fibre insulation
• Conductor Number: 5
• Thread Size: M18 x 1,5
• Connector Shape: D Shape
• Cable Length [mm]: 1,510
• Supplementary Article/Supplementary Info: with cable tie
• Oxygen Sensor: Broadband oxygen sensor, Thread pre-greased
• Number of circuits: 5
• Weight [kg]: 0.155
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.