Assembly categories
Filters Brake System Axle Steering Cooling / AC Electrics Towbar/Accessories Transmission Exhaust System Body Ignition Engine Windscreen Cleaning Lights Fuel Supply Interior ServiceProduct
Description
In stock
Price
(incl. VAT)
- Number of circuits: 4
- Oxygen Sensor: Regulating Probe
- Manufacturer: KAMOKA
- Oxygen Sensor: Regulating Probe
- Length [mm]: 520
-
Fabrication Number: ESL-
VW- 008 - Manufacturer: NTY
Tavatellimus saadetakse E, K ja R kell 14:00. Kaup saabub kuni 3'e tööpäevaga. Tavatellimusse lähevad ainult positiivse laojäägiga tooted. Lisaks tavatellimusele on võimalik tellida ka Express kulleriga (24h). Kulleri hinda täpsusta 6 599 702, malva@lakiauto.ee.
- Engine Code: BUD
- Oxygen Sensor: Heated
- Number of circuits: 4
- Cable Length [mm]: 420
- Name: Lambda andur
- Manufacturer: MAX
-
Fitting Position: Front,
before catalytic converter - Oxygen Sensor: Regulating Probe
- Length [mm]: 560
- Number of pins: 4
- Lisainfo: Lambda Sensor
- Additional information: Lambda Sensor
- Oxygen Sensor: Oxygen Sensor
- Voltage [V]: 12
- Guarantee: 3 years guarantee
- Number of circuits: 4
- Weight [kg]: 0.09
- Resistor [Ohm]: 9
- Operating Mode: Electric
- Always compare old and new part (in particular OE No.):
- Manufacturer: SKV GERMANY
- Name: CE 09SKV909
- Oxygen Sensor: Oxygen Sensor
- Voltage [V]: 12
- Guarantee: 3 years guarantee
- Number of circuits: 4
- Weight [kg]: 0.14
- Operating Mode: Electric
- Always compare old and new part (in particular OE No.):
- Name: CE 09SKV904
- Manufacturer: ESEN SKV
- Construction Year from: 05.2006
-
Fitting Position: Front,
after catalytic converter -
Oxygen Sensor: Diagnostic Probe,
Heated - Length [mm]: 480
- Number of circuits: 4
- Name: Lambda andur
- Manufacturer: MAX
- Engine Code: BUD
-
Exhaust System: for pre-
catalytic converter - Quality: OE
- Manufacturer Restriction: DENSO
- Thread Size: M18x1.5
- Cable Length [mm]: 750
- Number of pins: 4
- Weight [g]: 103
- Gross Weight [g]: 152
- Manufacturer: DENSO
-
Name: DN DOX-
0119 - Quality class: Q
Oxygen Sensor: Regulating Probe, Heated, Finger probe, Oxygen Sensor
Additional information: "Tootja: DENSO
ESCORT VII SEDAN (GA
(kvaliteediklass: Q)"
Lisainfo: "Tootja: DENSO
ESCORT VII SEDAN (GA
(kvaliteediklass: Q)"
- Construction Year from: 05.2006
-
Oxygen Sensor: Regulating Probe,
Diagnostic Probe, Finger probe - Block Separation:
- Number of circuits: 4
- Connector/Clamp: Connector may need adjustment
- Transmission Type: Manual Transmission
- Name: LAMBDA ANDUR
- Manufacturer: MAX
Fitting Position: before catalytic converter, after catalytic converter
-
Oxygen Sensor: Diagnostic Probe,
Planar probe, Heated - Fitting Position: after catalytic converter
- Cable Length [mm]: 480
- Name: LAMBDA ANDUR
- Manufacturer: DLP
Additional information: "Tootja: DELPHI
(kvaliteediklass: PJ)"
Lisainfo: "Tootja: DELPHI
(kvaliteediklass: PJ)"
- Construction Year from: 05.2006
-
Oxygen Sensor: Diagnostic Probe,
Heated - Fitting Position: after catalytic converter
- Number of circuits: 4
- Overall Length [mm]: 750
- Name: Lambda andur
- Manufacturer: MAX
-
Oxygen Sensor: Diagnostic Probe,
Unheated - Number of pins: 4
- Connector Shape: D Shape
- Socket colour: black
- Cable Length [mm]: 920
- for OE number: 06E906265K
- Manufacturer: MEAT&DORIA
- Conductor Number: 4
- Number of circuits: 4
- Length [mm]: 721
- Resistor [Ohm]: 9
- Cable Length [mm]: 721
- Oxygen Sensor: Heated
- Name: LAMBDA ANDUR
- Manufacturer: MAG
- Construction Year from: 05.2006
- Oxygen Sensor: Diagnostic Probe
- Voltage [V]: 12
- Length [mm]: 681
- Guarantee: 3 years guarantee
- Number of circuits: 4
- Weight [kg]: 0.13
- Resistor [Ohm]: 6
- Operating Mode: Electric
- Always compare old and new part (in particular OE No.):
- Manufacturer: SKV GERMANY
- Name: CE 09SKV672
- Engine Code: BUD
-
Oxygen Sensor: Diagnostic Probe,
Heated -
External Thread Size: M18 x 1,
5 - Spanner Size: 22
- Number of circuits: 4
- Cable Length [mm]: 570
- Weight [kg]: 0.106
- Manufacturer: FEBI BILSTEIN
General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.
-
Oxygen Sensor: Regulating Probe,
Finger probe, Heated - Fitting Position: before catalytic converter
- Cable Length [mm]: 513
-
Name: DE ES11118-
12B1 - Manufacturer: DELPHI
- Engine Code: BUD
-
Oxygen Sensor: Heated,
Regulating Probe -
External Thread Size: M18 x 1,
5 - Spanner Size: 22
- Number of circuits: 4
- Cable Length [mm]: 520
- Weight [kg]: 0.1
- Name: SW 33 10 3137
- Manufacturer: SWAG
General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.
- Engine Code: BUD
-
Oxygen Sensor: Diagnostic Probe,
Heated -
External Thread Size: M18 x 1,
5 - Spanner Size: 22
- Number of circuits: 4
- Cable Length [mm]: 570
- Weight [kg]: 0.106
- Name: SW 33 10 3138
- Manufacturer: SWAG
General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.
- Oxygen Sensor: Oxygen Sensor
- Cable Length [mm]: 290
- Alternatively:
- Number of circuits: 4
- Alternative Repair Kit: 570112
- Manufacturer: ERA
- Construction Year from: 05.2006
-
Oxygen Sensor: Diagnostic Probe,
Heated - Voltage [V]: 12
- Length [mm]: 595
- Guarantee: 3 years guarantee
- Number of circuits: 4
- Weight [kg]: 0.13
- Resistor [Ohm]: 6
- Operating Mode: Electric
- Always compare old and new part (in particular OE No.):
- Manufacturer: ESEN SKV
- Construction Year from: 05.2006
- Oxygen Sensor: Diagnostic Probe
- Length [mm]: 500
- Number of connectors: 4
- Manufacturer: VERNET
- Fitting Position: Exhaust Manifold
-
Line insulation design: with silicone-
coated woven- fibre insulation - Connector Shape: D Shape
- for OE number: 03C 906 262 T
- Weight [kg]: 0.131
-
Thread Size: M18 x 1,
5 - Number of circuits: 4
- Socket colour: brown
- Overall Length [mm]: 400
- Number of pins: 4
- Number of connectors: 4
-
Oxygen Sensor: Regulating Probe,
Thread pre- greased - Exhaust System: before catalytic converter
- Manufacturer: VEMO GERMANY
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Construction Year from: 05.2006
-
Vehicle Identification Number (VIN) from: 1Z-
5- 000 001 - Fitting Position: after catalytic converter
-
Line insulation design: with silicone-
coated woven- fibre insulation -
Oxygen Sensor: Planar probe,
Heated, Thread pre- greased - Cable Length [mm]: 210
- Number of circuits: 4
- Weight [kg]: 0.09
- Manufacturer: VEMO GERMANY
Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Construction Year from: 05.2006
-
Oxygen Sensor: Regulating Probe,
Diagnostic Probe - Block Separation:
- Number of circuits: 4
-
Recommended change interval [km]: 160,
000 - Connector/Clamp: Connector may need adjustment
- Name: LAMBDA ANDUR
- Manufacturer: BOS
Fitting Position: before catalytic converter, after catalytic converter
- Engine Code: BUD
-
Line insulation design: with silicone-
coated woven- fibre insulation -
Thread Size: M18 x 1,
5 - Cable Length [mm]: 600
- Conductor Number: 4
- Connector Shape: D Shape
- Length [mm]: 520
- Number of pins: 4
- Number of connectors: 4
- Housing Colour: black
-
Oxygen Sensor: Heated,
Thread pre- greased - Weight [kg]: 0.12
- Manufacturer: VEMO GERMANY
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Engine Code: BUD
-
Exhaust System: for pre-
catalytic converter - for OE number: 036906262AA
- Quality: OE
- Manufacturer Restriction: DENSO
- Thread Size: M18x1.5
- Cable Length [mm]: 620
- Number of pins: 4
- Weight [g]: 107
- Gross Weight [g]: 138
- Manufacturer: DENSO
- Quality class: Q
- Name: Lambda sensor
Oxygen Sensor: Regulating Probe, Heated, Finger probe, Oxygen Sensor
- Construction Year from: 05.2006
- Oxygen Sensor: Diagnostic Probe
- Fitting Position: after catalytic converter
- Number of circuits: 4
- Overall Length [mm]: 750
- Available as universal article as well, see article no.: 0258986602
-
Recommended change interval [km]: 160,
000 - Name: LAMBDA ANDUR
- Manufacturer: BOS
- Fitting Position: after catalytic converter
- Number of pins: 4
- Cable Length [mm]: 570
-
Thread Size: M18x1,
5 - Switch Pressure [bar]: 4
- Connector Shape: oval
- Weight [kg]: 0.14
- Name: VA 368078
- Manufacturer: VALEO
Oxygen Sensor: Diagnostic Probe, Planar probe, Thread pre-greased, Heated
- Construction Year from: 05.2006
- Fitting Position: after catalytic converter
- Oxygen Sensor: Diagnostic Probe
- Cable Length [mm]: 750
- Number of pins: 4
- Assy./disassy. by qualified personnel required!:
- Manufacturer: HELLA
- Name: HE 6PA358066421
Brief Information: *** HELLA Electronics OE competence for over 60 years.
-
Oxygen Sensor: Diagnostic Probe,
Heated - Fitting Position: after catalytic converter
-
Engine Code: BUD,
CGGA - Construction Year from: 05.2006
- Length [mm]: 550
- Number of pins: 4
- Technical Information Number: Universal 77004
- Socket colour: black
- Manufacturer: FAE
- Oxygen Sensor: Regulating Probe
- Number of pins: 4
- Length [mm]: 600
- Housing Colour: brown
- Manufacturer: METZGER
- Oxygen Sensor: Diagnostic Probe
- Engine Code: BUD
- Construction Year from: 06.2006
- Number of pins: 4
- Length [mm]: 550
- Housing Colour: black
- Alternative Repair Kit: 0893355
- Manufacturer: METZGER
-
Oxygen Sensor: Regulating Probe,
Heated - Fitting Position: before catalytic converter
- Engine Code: BUD
- Construction Year from: 05.2006
- Length [mm]: 520
- Number of pins: 4
- Technical Information Number: Universal 77004
- Socket colour: brown
- Manufacturer: FAE
- Construction Year from: 05.2006
- Oxygen Sensor: Regulating Probe
- Fitting Position: before catalytic converter
- Manufacturer: BOSCH
- Construction Year from: 11.2008
- Construction Year to: 11.2010
- Engine Code: BUD
- Fitting Position: before catalytic converter
- Number of pins: 6
- Cable Length [mm]: 735
-
Thread Size: M18x1,
5 - Switch Pressure [bar]: 4
- Connector Shape: oval
- Weight [kg]: 0.19
- Manufacturer: VALEO
- Name: VA 368403
Oxygen Sensor: Planar probe, Broadband oxygen sensor, Thread pre-greased, Heated
Laki Auto universal products
TecDoc catalogue for cars
TecDoc catalogue for trucks