• Number of pins: 2
• Connector Shape: oval
• Socket colour: green
• Thread Size: M12x1,5
• Sensor Type: NTC Sensor
• Spanner Size: 19 mm
• for OE number: XM34 12A648 AA, LNA1600AA, 13650 61B00
• Manufacturer: MEAT&DORIA

• Engine Code: 3ZZ-FE
• Number of pins: 2
• Supplementary Article/Info 2: with seal ring
• Housing Colour: green
• Supplementary Article/Supplementary Info: with seal
• Thread Size: M12x1,5
• Weight [kg]: 0.032
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: 3ZZ-FE
• Housing Colour: green
• Thread Size: M12x1,5
• Spanner Size: 19
• for article number: 1.880.113, 1.880.114, 1.880.149, 1.880.151
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Fabrication Number: ECP-TY-017
• Manufacturer: NTY

• Sensor Type: Inductive Sensor
• Number of pins: 2
• Manufacturer: ABAKUS DEPO/LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis.

• Number of pins: 2
• Housing Colour: green
• Thread Size: M 12x1,5
• Manufacturer: FAE

• Fabrication Number: ESS-TY-001
• Manufacturer: NTY

• Required quantity: 1
• Number of pins: 2
• Sensor Type: Inductive Sensor
• Supplementary Article/Info 2: without cable
• Housing Colour: black
• Name: CZUJNIK POO½ENIA WAKA ROZRZ. TOYOTA
• Manufacturer: BRM

• Number of pins: 2
• Weight [kg]: 0.043
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Voltage [V]: 12
• Supplementary Article/Supplementary Info: without cable pull
• Number of pins: 3
• Weight [kg]: 0.04
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 17SKV253
• Manufacturer: ESEN SKV

• Number of pins: 2
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: DLP

• Number of pins: 2
• Manufacturer: ERA

• Lambda Sensor: Regulating Probe, Thread pre-greased
• Thread Size: M18x1.5
• Cable Length [mm]: 435
• Number of pins: 4
• Fitting Position: before catalytic converter
• Fabrication Number: ESL-TY-018

• Number of pins: 2
• Sensor Type: Inductive Sensor
• Supplementary Article/Info 2: without cable
• Manufacturer: MEAT&DORIA

• Fitting Position: Front, before catalytic converter
• Lambda Sensor: Regulating Probe, Thread pre-greased
• Fabrication Number: ESL-TY-019
• Manufacturer: NTY

• Construction Year from: 10.2001
• Construction Year to: 12.2003
• Sensor Type: Hall Sensor
• Number of pins: 3
• Connector Shape: oval
• Supplementary Article/Info 2: without cable
• Weight [kg]: 0.03
• Manufacturer: VALEO
• Name: VA 366136

• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Housing Type: without housing
• Fabrication Number: EPP-TY-000
• Manufacturer: NTY

• Fitting Position: Upper
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: TRI

• Component Number: 120-08-106
• Manufacturer: ABAKUS DEPO/LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis.

• Number of connectors: 2
• Weight [kg]: 0.06
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of connectors: 2
• Weight [kg]: 0.06
• Manufacturer: BLUEPRINT

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Cable Length [mm]: 250
• Number of pins: 3
• Housing Colour: black
• Manufacturer: FAE

• Construction Year from: 10.2001
• Construction Year to: 12.2003
• Sensor Type: Inductive Sensor
• Number of pins: 2
• Connector Shape: oval
• Supplementary Article/Info 2: without cable
• Weight [kg]: 0.05
• Manufacturer: VALEO

• Engine Code: 3ZZ-FE, 3ZZFE
• Required quantity: 1
• Country Specific Design: Japan
• Manufacturer: FACET
• Name: EP 1.953.500

• Lambda Sensor: Lambda Sensor
• Voltage [V]: 12
• Number of circuits: 4
• Weight [kg]: 0.09
• Resistor [Ohm]: 13
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV913
• Manufacturer: ESEN SKV

• Engine Code: 3ZZ-FE
• Lambda Sensor: Diagnostic Probe
• Number of circuits: 4
• Supplementary Article/Info 2: without plug
• Manufacturer: ENERGY

• Construction Year to: 01.2004
• Lambda Sensor: Regulating Probe, Diagnostic Probe, Finger probe
• Block Separation:
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Transmission Type: Manual Transmission
• Name: LAMBDA ANDUR
• Manufacturer: MAX

Fitting Position: before catalytic converter, after catalytic converter

• Required quantity: 1
• Number of pins: 2
• Weight [g]: 33
• Country Specific Design: Japan
• not for country specific design: Japan
• Gross Weight [g]: 60
• Manufacturer: DENSO
• Name: DN DCPS0116

• Number of pins: 5
• Housing Type: without housing
• Manufacturer: JP GROUP
• Lisainfo: Air Mass Sensor
• Additional information: Air Mass Sensor

• Construction Year to: 01.2004
• Quality: OE
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 103
• Gross Weight [g]: 147
• Manufacturer: DENSO
• Lisainfo: DOX-0109 DENSO
• Additional information: DOX-0109 DENSO

Lambda Sensor: Diagnostic Probe, Heated, Finger probe, Lambda Sensor

• Supplementary Article/Supplementary Info: without suction pipe
• Number of pins: 5
• Quality class: PJ
• Name: Air flow sensor

• Fitting Position: Front, before catalytic converter
• Length [mm]: 480
• Thread Size: M18x1.5mm
• Number of pins: 4
• Lambda Sensor: Heated, Planar probe
• Manufacturer: KAVO

• Resistor [Ohm]: 13
• Conductor Number: 4
• Length [mm]: 570
• Number of circuits: 4
• Cable Length [mm]: 570
• Lambda Sensor: Heated
• Name: LAMBDA ANDUR
• Manufacturer: MAG

• Number of pins: 2
• Resistor [Ohm]: 1,100
• Housing Colour: black
• Manufacturer: METZGER

• Lambda Sensor: Regulating Probe, Planar probe, Heated
• Fitting Position: before catalytic converter
• Block Separation:
• Exhaust System: for pre-catalytic converter
• Cable Length [mm]: 492
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Number of pins: 5
• Fitting Position: Air Filter Housing
• Recommended additional repairs: Air Filter
• Manufacturer: TOPRAN HANS PRIES

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Number of pins: 2
• Housing Colour: black
• Supplementary Article/Info 2: without cable
• Manufacturer: FAE

• Lambda Sensor: Regulating Probe, Heated
• Fitting Position: Exhaust Manifold
• Number of pins: 4
• Cable Length [mm]: 350
• Manufacturer: MEAT&DORIA

• Number of pins: 2
• Manufacturer: DELPHI
• Name: DE AS10172

• Quality: OE EQUIVALENT
• Manufacturer: MEAT&DORIA

• Voltage [V]: 12
• Number of pins: 5
• Weight [kg]: 0.07
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 07SKV103

• Height [mm]: 30
• Resistor [Ohm]: 1,100
• Number of connectors: 2
• Manufacturer: VERNET

• Lambda Sensor: Diagnostic Probe
• Construction Year to: 12.2003
• Voltage [V]: 12
• Length [mm]: 575
• Number of circuits: 4
• Weight [kg]: 0.15
• Resistor [Ohm]: 13
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV741

• Lambda Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Vehicle type: Corolla Verso
• Cable Length [mm]: 520
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Name: LAMBDA ANDUR
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Line insulation design: with silicone-coated woven-fibre insulation
• Lambda Sensor: Planar probe, Heated, Thread pre-greased
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Manufacturer: VEMO GERMANY

Fitting Position: before catalytic converter, after catalytic converter Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Voltage [V]: 12
• Number of pins: 5
• Weight [kg]: 0.11
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 07SKV151

• Voltage [V]: 12
• Number of pins: 5
• Weight [kg]: 0.11
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Construction Year to: 01.2004
• Lambda Sensor: Regulating Probe, Diagnostic Probe
• Block Separation:
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

Fitting Position: before catalytic converter, after catalytic converter

• Lambda Sensor: Diagnostic Probe, Finger probe, Heated
• Fitting Position: after catalytic converter
• Cable Length [mm]: 570
• Name: LAMBDA ANDUR
• Manufacturer: DLP
• Additional information: ES11106-12B1 DELPHI
• Lisainfo: ES11106-12B1 DELPHI

• Lambda Sensor: Regulating Probe, Thread pre-greased
• Fitting Position: Exhaust Manifold
• Line insulation design: with silicone-coated woven-fibre insulation
• Cable Length [mm]: 303
• Number of pins: 4
• Weight [kg]: 0.098
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 12.2003
• Lambda Sensor: Lambda Sensor
• Voltage [V]: 12
• Weight [kg]: 0.08
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV084

• Lambda Sensor: Regulating Probe, Lambda Sensor
• Construction Year to: 01.2004
• Exhaust System: before catalytic converter
• Voltage [V]: 12
• Weight [kg]: 0.08
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV086

• Engine Code: 3ZZ-FE
• Fitting Position: after catalytic converter
• Cable Length [mm]: 250
• Conductor Number: 4
• Number of circuits: 4
• Manufacturer: EPS

Lambda Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased

• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 5
• Housing Type: without housing
• Name: OHUMASSIMOOTJA
• Manufacturer: BRM

• Lambda Sensor: Regulating Probe
• Construction Year to: 01.2004
• Voltage [V]: 12
• Weight [kg]: 0.06
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV114

• Number of pins: 2
• Manufacturer: FAE

• Mounting Type: Bolted
• Number of pins: 5
• Manufacturer Restriction: 8ET 009 142- 901
• Supplementary Article/Supplementary Info: without suction pipe
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Engine Code: 3ZZ-FE
• Housing Type: without housing
• Name: EP 1.991.163
• Manufacturer: EPS

• Construction Year to: 01.2004
• for OE number: 89465-13040, 8946502080
• Quality: OE
• Manufacturer Restriction: DENSO
• Connector type: with rubber grommet
• Thread Size: M18x1.5
• Cable Length [mm]: 585
• Number of pins: 4
• Weight [g]: 101
• Gross Weight [g]: 134
• Manufacturer: DENSO
• Name: DN DOX-0240
• Quality class: Q

Lambda Sensor: Diagnostic Probe, Heated, Finger probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
AVENSIS STATION WAGO
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
AVENSIS STATION WAGO
(kvaliteediklass: Q)"

• Alternatively:
• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 5
• Housing Type: without housing
• Manufacturer: BREMI

• Number of connectors: 2
• Weight [kg]: 0.044
• for OE number: 8961520090
• Name: DETONATSIOONIANDUR
• Manufacturer: BLP

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Construction Year to: 01.2004
• for OE number: 89465-13030, 8946505080
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 435
• Number of pins: 4
• Weight [g]: 94
• Gross Weight [g]: 127
• Manufacturer: DENSO
• Name: DN DOX-0254
• Quality class: Q

Lambda Sensor: Regulating Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
AVENSIS STATION WAGO
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
AVENSIS STATION WAGO
(kvaliteediklass: Q)"

• Operating Mode: Electric
• Manufacturer: MAGNETI MARELLI

• Housing Type: without housing
• Number of pins: 5
• Plug Type: Male
• Housing Colour: black
• Voltage [V]: 12
• Recommended additional repairs: Air Filter
• Name: OHUMASSIMOOTJA
• Manufacturer: DLP

• Voltage [V]: 12
• Housing Type: without housing
• Number of pins: 5
• Supplementary Article/Info 2: with seal ring
• Number of Holes: 2
• Manufacturer: ERA

• Construction Year to: 01.2004
• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 470
• Available as universal article as well, see article no.: 0258986602
• Recommended change interval [km]: 160,000
• Manufacturer: BOSCH

• for OE number: 22204-22010
• Quality: OE
• Operating Mode: Electric
• Number of pins: 5
• Gross Weight [g]: 79
• Manufacturer: DENSO
• Name: DN DMA-0108

Additional information: "Tootja: DENSO
FORTUNER SAMOCHÓD TE
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
FORTUNER SAMOCHÓD TE
(kvaliteediklass: Q)"

• Resistor Type: Hot-wire Sensor
• Number of connectors: 5
• Colour: black
• Material: Plastic
• Supplementary Article/Supplementary Info: with seal
• Weight [kg]: 0.051
• Housing Type: without housing
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: 3ZZ-FE
• Operating Mode: Electric
• Voltage [V]: 12
• Name: OHUMASSIMOOTJA
• Manufacturer: PIE