Fabrication Number: ECT-TY-002

• Engine Code: 2AZ-FSE
• Manufacturer Restriction: TOKAIRIKA
• Colour: black
• Pressure [bar]: 0
• Thread Size: 1/8 GAS
• Spanner Size: 24
• Name: OLISURVELšLITUS
• Manufacturer: EPS

• Switch Pressure [bar]: 0.2
• Thread Size: 1/8x28 BSPT
• Sensor Type: Closed-type Sensor
• Name: OLISURVELšLITUS
• Manufacturer: VER
• Additional information: OS3557
• Lisainfo: OS3557

Manufacturer: BOSCH

• Number of pins: 2
• Sensor Type: NTC Sensor
• Colour Coding: green
• Thread Size: M 12
• Thread Pitch [mm]: 1.5
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Pressure [bar]: 0.2
• Thread Size: 1/8 GAS
• Number of pins: 1
• Technical Information Number: circuit N.C.
• Manufacturer: ERA

• Pressure [bar]: 2
• Housing Colour: grey
• Thread Size: R1/8
• Diameter [mm]: 24
• Spanner Size: 24
• Number of pins: 1
• Name: OLISURVELšLITUS
• Manufacturer: DLP

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: rectangular
• Number of pins: 2
• Spanner Size: 19
• Thread Size: M12x1.5
• for OE number: 195321101000
• Supplementary Article/Info 2: with seal ring
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: rectangular
• Number of pins: 2
• Spanner Size: 19
• Thread Size: M12x1.5
• for OE number: J8942220010
• Supplementary Article/Info 2: with seal ring
• Manufacturer: NRF

• Thread Size: 1/8x28 BSP
• Pressure [bar]: 0.2
• Manufacturer: FAE

• Connector Shape: oval
• Material: Plastic
• Number of pins: 2
• Plug Type: Female
• Sensor Type: NTC Sensor
• Spanner Size: S19
• Thread Size: M12*1,5
• Name: NI 207056
• Manufacturer: NISSENS

Technical Information: FIRST FIT - a time-saving installation! Find all additional parts such as O-rings, clip, washer in the box.

• Spanner Size: 19 mm
• Sensor Type: NTC Sensor
• Number of pins: 2
• Connecting thread: M12 x 1,5
• Manufacturer: ERA

• Connector Shape: rectangular
• Material: Plastic
• Number of pins: 2
• Plug Type: Female
• Sensor Type: NTC Sensor
• Spanner Size: S19
• Thread Size: M12*1,5
• Name: NI 207076
• Manufacturer: NISSENS

Technical Information: FIRST FIT - a time-saving installation! Find all additional parts such as O-rings, clip, washer in the box.

• Engine Code: 2AZ-FSE
• Housing Colour: green
• Thread Size: M12x1,5
• Spanner Size: 19
• for article number: 1.880.113, 1.880.114, 1.880.149, 1.880.151
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Mounting Type: Bolted
• Voltage [V]: 12
• Resistor [Ohm]: 2,080, 280
• Supplementary Article/Supplementary Info: with seal
• Temperature range from [°C]: 25
• Temperature range to [°C]: 80
• Thread Size: M12x1,5
• Colour: green
• Sensor Type: NTC Sensor
• Number of pins: 2
• Colour Coding: grey
• Corresponds to the original part in colour: green
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PT009107481

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Fabrication Number: ECP-TY-017
• Manufacturer: NTY

• Colour: blue
• Housing Colour: blue
• Number of pins: 2
• Thread Size: M12X1.5-6g
• Spanner Size: 19
• Manufacturer: DELPHI
• Name: DE TS10250

• Engine Code: 2AZ-FSE
• Sensor Type: NTC Sensor
• Thread Size: M12 x 1,5
• Spanner Size: 19
• Colour: blue
• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MEY

• Engine Code: 2AZ-FSE
• Thread Size: M12x1.5
• Manufacturer: VERNET

• Cable Length [mm]: 340
• Fabrication Number: ECP-TY-002
• Manufacturer: NTY

• Number of pins: 2
• Supplementary Article/Supplementary Info: with seal
• Weight [kg]: 0.3
• Packaging length [cm]: 12
• Packaging width [cm]: 8
• Packaging height [cm]: 6

• Colour: green
• Number of pins: 2
• Supplementary Article/Supplementary Info: with seal
• Weight [kg]: 0.3
• Packaging length [cm]: 12
• Packaging width [cm]: 8
• Packaging height [cm]: 6

• Fabrication Number: ESS-TY-001
• Manufacturer: NTY

• Sensor Type: Active sensor
• for OE number: 13 62 7 808 449
• Manufacturer: KAMOKA

• Number of pins: 2
• Sensor Type: Inductive Sensor
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Required quantity: 1
• Number of pins: 2
• Sensor Type: Inductive Sensor
• Supplementary Article/Info 2: without cable
• Housing Colour: black
• Name: CZUJNIK POO½ENIA WAKA ROZRZ. TOYOTA
• Manufacturer: BRM

Manufacturer: MAGNETI MARELLI

• Required quantity: 1
• Number of pins: 2
• Sensor Type: Inductive Sensor
• Supplementary Article/Info 2: with cable
• Housing Colour: black
• Manufacturer: BREMI

• Supplementary Article/Info 2: with plug
• Number of wires (repair kit, cable set): 2
• Manufacturer: ABA

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. Name: Kaabli remondikomplekt, jahutusvedeliku temperatuuri andur

• Quantity: 1
• Number of pins: 2
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: DLP

• Voltage [V]: 12
• Supplementary Article/Supplementary Info: without cable pull
• Number of pins: 3
• Weight [kg]: 0.04
• Operating Mode: Electric
• Warranty: 3 years warranty
• Name: CE 17SKV253
• Manufacturer: ESEN SKV

• Number of pins: 2
• Manufacturer: ERA

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Thread Size: M18x1.5
• Cable Length [mm]: 655
• Number of pins: 4
• Fitting Position: Left, after catalytic converter
• Fabrication Number: ESL-TY-023
• Manufacturer: NTY

• Lambda Sensor: Regulating Probe, Thread pre-greased
• Fabrication Number: ESL-TY-017
• Manufacturer: NTY

Fitting Position: Left Front, Right Front, before catalytic converter

• Cable Length [mm]: 360
• Alternatively:
• Number of pins: 2
• Alternative Repair Kit: 550442
• Fitting Depth [mm]: 36
• Resistor [kOhm]: 1.4
• Manufacturer: ERA

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Thread Size: M18x1.5
• Cable Length [mm]: 630
• Number of pins: 4
• Fitting Position: Right, after catalytic converter
• Fabrication Number: ESL-TY-024
• Manufacturer: NTY

• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Housing Type: without housing
• Fabrication Number: EPP-TY-000
• Manufacturer: NTY

• Cable Length [mm]: 330
• Sensor Type: Inductive Sensor
• Number of pins: 2
• Supplementary Article/Info 2: with seal ring
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PU013122761
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Number of pins: 2
• Housing Colour: grey
• Manufacturer: FAE

• Quantity: 1
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: TRI

• Number of pins: 2
• Connector Shape: oval
• Manufacturer: METZGER

• Component Number: 120-08-106
• Manufacturer: ABAKUS DEPO/LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis.

• Cable Length [mm]: 340
• Number of pins: 2
• Name: ANDUR, VŽNTVOLL
• Manufacturer: DLP

• Engine Code: 2AZ-FSE
• Required quantity: 1
• Country Specific Design: Japan
• Name: ANDUR, VŽNTVOLL
• Manufacturer: EPS

• Lambda Sensor: Lambda Sensor
• Voltage [V]: 12
• Number of circuits: 4
• Weight [kg]: 0.09
• Resistor [Ohm]: 13
• Operating Mode: Electric
• Warranty: 3 years warranty
• Name: CE 09SKV913
• Manufacturer: ESEN SKV

• Required quantity: 1
• Number of pins: 2
• Weight [g]: 33
• Country Specific Design: Japan
• not for country specific design: Japan
• Gross Weight [g]: 60
• Manufacturer: DENSO
• Name: DN DCPS0116

• Number of pins: 2
• Cable Length [mm]: 377
• Fitting Depth [mm]: 36.2
• Name: ANDUR, VŽNTVOLL
• Manufacturer: TRI

• Engine Code: 2AZ-FSE
• Fitting Position: Right
• Lambda Sensor: Regulating Probe, Heated
• Construction Year to: 10.2008
• Number of circuits: 4
• Length [mm]: 330
• Name: Lambda andur
• Manufacturer: MAX

• Line insulation design: with silicone-coated woven-fibre insulation
• Socket colour: grey
• for OE number: 89465 30430
• Length [mm]: 800
• Weight [kg]: 0.122
• Thread Size: M18 x 1,5
• Supplementary Article/Info 2: with fastening material
• Connector Shape: angular
• Number of circuits: 4
• Cable Length [mm]: 800
• Number of pins: 4
• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Exhaust System: after catalytic converter
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Left Front, Right Front
• Exhaust System: after catalytic converter
• Lambda Sensor: Diagnostic Probe
• Length [mm]: 865
• Number of connectors: 4
• Manufacturer: VERNET

• Fitting Position: Left, Right
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 103
• Gross Weight [g]: 147
• Manufacturer: DENSO
• Lisainfo: DOX-0109 DENSO
• Additional information: DOX-0109 DENSO

Lambda Sensor: Regulating Probe, Heated, Finger probe, Lambda Sensor

• Required quantity: 1
• Supplementary Article/Supplementary Info: without suction pipe
• Number of pins: 5
• Quality class: PJ
• Name: Air flow sensor

• Lambda Sensor: Regulating Probe, Lambda Sensor
• Construction Year to: 10.2008
• Engine Code: 2AZ-FSE
• Voltage [V]: 12
• Length [mm]: 392
• Number of circuits: 4
• Weight [kg]: 0.13
• Operating Mode: Electric
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY
• Name: CE 09SKV011

• Fitting Position: Left, Right, Front, before catalytic converter
• Lambda Sensor: Regulating Probe, Planar probe, Heated
• Quantity: 2
• Cable Length [mm]: 369
• Manufacturer: DELPHI
• Name: DE ES20118-12B1

• Lambda Sensor: Heated
• Number of pins: 4
• Cable Length [mm]: 500
• Fitting Position: Exhaust Manifold
• Manufacturer: MEAT&DORIA

• Number of pins: 5
• Fitting Position: Air Filter Housing
• Recommended additional repairs: Air Filter
• Manufacturer: TOPRAN HANS PRIES

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Lambda Sensor: Regulating Probe, Finger probe, Thread pre-greased
• Fitting Position: Left, Exhaust Manifold
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 570
• Number of pins: 4
• Weight [kg]: 0.174
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Left, Right, Front, before catalytic converter
• Lambda Sensor: Regulating Probe, Planar probe, Heated
• Quantity: 2
• Cable Length [mm]: 492
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Construction Year to: 10.2008
• Lambda Sensor: Diagnostic Probe
• Voltage [V]: 12
• Length [mm]: 410
• Number of circuits: 4
• Weight [kg]: 0.13
• Resistor [Ohm]: 13
• Operating Mode: Electric
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY
• Name: CE 09SKV583

• Number of pins: 2
• Manufacturer: DELPHI
• Name: DE AS10172

• Lambda Sensor: Lambda Sensor
• Cable Length [mm]: 290
• Alternatively:
• Number of circuits: 4
• Alternative Repair Kit: 570112
• Manufacturer: ERA

• Lambda Sensor: Regulating Probe, Diagnostic Probe
• Number of pins: 4
• Cable Length [mm]: 720
• Manufacturer: MEAT&DORIA

• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter, Rear, Front
• Block Separation:
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Engine Code: 2AZ-FSE
• Fitting Position: Left
• Line insulation design: with silicone-coated woven-fibre insulation
• Number of pins: 4
• for OE number: V99760001
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Length [mm]: 350
• Exhaust System: after catalytic converter
• Manufacturer: VEMO GERMANY

Lambda Sensor: Regulating Probe, Finger probe, Heated, Thread pre-greased Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Voltage [V]: 12
• Number of pins: 5
• Weight [kg]: 0.11
• Operating Mode: Electric
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY

• Height [mm]: 30
• Resistor [Ohm]: 1,100
• Number of connectors: 2
• Manufacturer: VERNET

• Lambda Sensor: Regulating Probe, Finger probe, Thread pre-greased
• Fitting Position: Left, Exhaust Manifold
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 350
• Number of pins: 4
• Weight [kg]: 0.174
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Regulating Probe, Lambda Sensor
• Exhaust System: before catalytic converter
• Voltage [V]: 12
• Weight [kg]: 0.12
• Operating Mode: Electric
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY
• Name: CE 09SKV112

• Fitting Position: Left
• for OE number: 89465-05100, 8946505100
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 360
• Number of pins: 4
• Weight [g]: 94
• Gross Weight [g]: 127
• Manufacturer: DENSO
• Name: Lambda sensor
• Quality class: Q

Lambda Sensor: Regulating Probe, Heated, Finger probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
CARINA E SEDAN (/T19
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
CARINA E SEDAN (/T19
(kvaliteediklass: Q)"

• Number of pins: 2
• Housing Colour: black
• Supplementary Article/Info 2: without cable
• Manufacturer: FAE

• Number of pins: 2
• Manufacturer: FAE

• Engine Code: 2AZ-FSE
• Construction Year from: 04.2006
• Fitting Position: Left, Right, Front, before catalytic converter
• Required quantity: 2
• Cable Length [mm]: 350
• Conductor Number: 4
• Available as universal article as well, see article no.: 1.998.235
• Number of circuits: 4
• Name: EP 1.998.522
• Manufacturer: EPS

Lambda Sensor: Regulating Probe, Heated, Planar probe, Thread pre-greased

• Lambda Sensor: Regulating Probe, Lambda Sensor
• Exhaust System: before catalytic converter
• Voltage [V]: 12
• Weight [kg]: 0.1
• Operating Mode: Electric
• Warranty: 3 years warranty
• Name: CE 09SKV113
• Manufacturer: ESEN SKV

• Fitting Position: Right
• for OE number: 89465-05110, 8946505110
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 420
• Number of pins: 4
• Weight [g]: 93
• Gross Weight [g]: 126
• Manufacturer: DENSO
• Name: DN DOX-0238

Lambda Sensor: Regulating Probe, Heated, Finger probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
AVENSIS STATION WAGO
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
AVENSIS STATION WAGO
(kvaliteediklass: Q)"

• Fitting Position: Left
• for OE number: 89465-05120, 8946505120
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 655
• Number of pins: 4
• Weight [g]: 107
• Gross Weight [g]: 140
• Manufacturer: DENSO
• Name: DN DOX-0287
• Quality class: Q

Lambda Sensor: Diagnostic Probe, Heated, Finger probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
AVENSIS SEDAN (T25),
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
AVENSIS SEDAN (T25),
(kvaliteediklass: Q)"

• Fitting Position: Right
• for OE number: 89465-05130, 8946505130
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 630
• Number of pins: 4
• Weight [g]: 105
• Gross Weight [g]: 138
• Manufacturer: DENSO
• Name: DN DOX-0288
• Quality class: Q

Lambda Sensor: Diagnostic Probe, Heated, Finger probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
AVENSIS (T25), 04.03
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
AVENSIS (T25), 04.03
(kvaliteediklass: Q)"

• Operating Mode: Electric
• Manufacturer: MAGNETI MARELLI

• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 5
• Housing Type: without housing
• Name: OHUMASSIMOOTJA
• Manufacturer: BRM

• Housing Type: without housing
• Number of pins: 5
• Plug Type: Male
• Housing Colour: black
• Voltage [V]: 12
• Recommended additional repairs: Air Filter
• Name: OHUMASSIMOOTJA
• Manufacturer: DLP

• Voltage [V]: 12
• Housing Type: without housing
• Number of pins: 5
• Supplementary Article/Info 2: with seal ring
• Number of Holes: 2
• Manufacturer: ERA

• Required quantity: 1
• Mounting Type: Bolted
• Number of pins: 5
• Manufacturer Restriction: 8ET 009 142- 901
• Supplementary Article/Supplementary Info: without suction pipe
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• for OE number: 22204-22010
• Quality: OE
• Operating Mode: Electric
• Number of pins: 5
• Gross Weight [g]: 79
• Manufacturer: DENSO
• Name: DN DMA-0108

Additional information: "Tootja: DENSO
FORTUNER SAMOCHÓD TE
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
FORTUNER SAMOCHÓD TE
(kvaliteediklass: Q)"