• DOT specification: DOT 4
• Chemical Properties: Synthetic
• Capacity [litre]: 1
• Dry Boiling Point [°C]: 245
• Packing Type: Bottle
• Lisainfo: 36-0048
• Additional information: 36-0048

Lisainfo: PFB401 TRW

• DOT specification: DOT 4
• Chemical Properties: Synthetic
• Capacity [litre]: 3
• Dry Boiling Point [°C]: 245
• Packing Type: Canister
• Lisainfo: 36-0049
  3 Liitrit
• Additional information: 36-0049
  3 Liitrit

• Quantity per packing unit: 24
• Dry Boiling Point [°C]: 260
• Wet Boiling Point [°C]: 160
• DOT specification: DOT 4
• Capacity [litre]: 0.25
• Weight [kg]: 0.301
• Observe service information:
• Manufacturer: FEBI BILSTEIN
• Additional information: FE26746
• Lisainfo: FE26746

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Quantity per packing unit: 24
• DOT specification: DOT 4
• Wet Boiling Point [°C]: 180
• Dry Boiling Point [°C]: 260
• DIN/ISO: ISO 4925
• Capacity [litre]: 0.25
• Specification: MB 331.0
• Weight [kg]: 0.301
• Observe service information:
• Manufacturer: FEBI BILSTEIN
• Additional information: FE26748
• Lisainfo: FE26748

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Quantity per packing unit: 24
• DOT specification: DOT 4, DOT 4 LV
• Dry Boiling Point [°C]: 265
• Wet Boiling Point [°C]: 170
• Capacity [litre]: 0.25
• Weight [kg]: 0.266
• Observe service information:
• Manufacturer: FEBI
• Lisainfo: 171876 FEBI
• Additional information: 171876 FEBI

DIN/ISO: ISO 4925 Class 3, ISO 4925 Class 4, ISO 4925 Class 6 General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Wet Boiling Point [°C]: 180
• DOT specification: DOT 5.1
• Dry Boiling Point [°C]: 260
• Capacity [litre]: 0.25
• Specification: FMVSS 116 DOT 5.1, ISO 4925 Classes 4, SAE J 1703
• Weight [kg]: 0.296
• Observe service information:
• Manufacturer: FEBI

DIN/ISO: ISO 4925 Class 3, ISO 4925 Class 4, ISO 4925 Class 5.1 General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Quantity per packing unit: 24
• Dry Boiling Point [°C]: 260
• Wet Boiling Point [°C]: 160
• DOT specification: DOT 4
• Capacity [litre]: 0.5
• Weight [kg]: 1.139
• Observe service information:
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• DOT specification: DOT 4
• Chemical Properties: Synthetic
• Capacity [litre]: 0.5
• Dry Boiling Point [°C]: 245
• Packing Type: Bottle
• Manufacturer: VALEO
• Name: VA 402402

• Wet Boiling Point [°C]: 184
• DOT specification: DOT 5.1
• Dry Boiling Point [°C]: 274
• Capacity [litre]: 0.25
• Weight [kg]: 0.296
• Observe service information:
• Manufacturer: FEBI BILSTEIN

DIN/ISO: ISO 4925 Class 3, ISO 4925 Class 4, ISO 4925 Class 5.1, ISO 4925 Class 6 Specification: FMVSS 116 DOT 5.1, ISO 4925 Classes 4, SAE J 1703, ISO 4925 Classes 6 General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Quantity per packing unit: 24
• Dry Boiling Point [°C]: 260
• DOT specification: DOT 4
• Wet Boiling Point [°C]: 180
• DIN/ISO: ISO 4925
• Capacity [litre]: 0.5
• Specification: MB 331.0
• Weight [kg]: 1.139
• Observe service information:
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Quantity per packing unit: 24
• DOT specification: DOT 4, DOT 4 LV
• Wet Boiling Point [°C]: 170
• Dry Boiling Point [°C]: 265
• Capacity [litre]: 0.5
• Weight [kg]: 1.064
• Observe service information:
• Manufacturer: FEBI

DIN/ISO: ISO 4925 Class 3, ISO 4925 Class 4, ISO 4925 Class 6 General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• DOT specification: DOT 4+
• Dry Boiling Point [°C]: 265
• Wet Boiling Point [°C]: 180
• Specification: FMVSS 116 DOT 4, SAE J 1703 / J 1704
• Chemical Properties: Synthetic
• Recommended change interval [years]: 2
• Packing Type: Bottle
• Capacity [litre]: 0.25
• Observe system fill quantity:
• Observe the vehicle manufacturer specifications:
• Weight [kg]: 0.28
• Height [mm]: 50
• Width [mm]: 45
• Length [mm]: 70
• Recommended change interval [km]: 40,000
• DIN/ISO: ISO 4925
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Quantity per packing unit: 24
• Wet Boiling Point [°C]: 180
• DOT specification: DOT 5.1
• Dry Boiling Point [°C]: 260
• Capacity [litre]: 0.5
• Specification: FMVSS 116 DOT 5.1, ISO 4925 Classes 4, SAE J 1703
• Weight [kg]: 0.296
• Observe service information:
• Manufacturer: FEBI-UKLAD HAMULCOWY

DIN/ISO: ISO 4925 Class 3, ISO 4925 Class 4, ISO 4925 Class 5.1 General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• DOT specification: DOT 4
• Wet Boiling Point [°C]: 160
• Dry Boiling Point [°C]: 260
• Capacity [litre]: 1
• Weight [kg]: 1.139
• Observe service information:
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• DOT specification: DOT 4
• Chemical Properties: Synthetic
• Capacity [litre]: 1
• Dry Boiling Point [°C]: 245
• Packing Type: Bottle
• Weight [kg]: 1.15
• Manufacturer: VALEO

• Quantity per packing unit: 24
• Wet Boiling Point [°C]: 184
• Dry Boiling Point [°C]: 274
• DOT specification: DOT 5.1
• Capacity [litre]: 0.5
• Weight [kg]: 0.296
• Observe service information:
• Manufacturer: FEBI

DIN/ISO: ISO 4925 Class 3, ISO 4925 Class 4, ISO 4925 Class 5.1, ISO 4925 Class 6 Specification: FMVSS 116 DOT 5.1, ISO 4925 Classes 4, SAE J 1703, ISO 4925 Classes 6 General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Wet Boiling Point [°C]: 170
• Dry Boiling Point [°C]: 265
• DOT specification: DOT 4, DOT 3, DOT 4 LV
• Packing Type: Bottle
• Recommended change interval [years]: 2
• Recommended change interval [km]: 40,000
• Capacity [litre]: 0.5
• Oil Viscosity Classification SAE: J 1703 / J 1704
• Observe service information:
• Manufacturer: VAICO

Hydraulic fluid manufacturer recommendation: W TL 766-Z, VW 50 114, BMW QV 34 001, GM Europa GMW 3356, PSA STL S71 2114, Ford WSS-M6C65-A2 DIN/ISO: ISO 4925 Class 3, ISO 4925 Class 4, ISO 4925 Class 6 General Information: Products supplied by us are without exception intended for the designated use. Please note that our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist personnel. There is no guarantee for inappropriate, improper or unintended use.

• Dry Boiling Point [°C]: 260
• Wet Boiling Point [°C]: 180
• DOT specification: DOT 4
• DIN/ISO: ISO 4925
• Capacity [litre]: 1
• Specification: MB 331.0
• Weight [kg]: 1.139
• Observe service information:
• Manufacturer: FEBI BILSTEIN
• Additional information: FE23930
• Lisainfo: FE23930

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Wet Boiling Point [°C]: 155
• DOT specification: DOT 4
• Dry Boiling Point [°C]: 260
• Chemical Properties: Synthetic
• Capacity [litre]: 0.5
• Recommended change interval [years]: 2
• Observe system fill quantity:
• Observe the vehicle manufacturer specifications:
• Height [mm]: 174
• Packing Type: Bottle
• DIN/ISO: ISO 4925 Class 4, ISO 4925
• Width [mm]: 58
• Weight [kg]: 0.6, 0.858
• Specification: FMVSS 116 DOT 4, SAE J 1703 F
• Length [mm]: 95
• Recommended change interval [km]: 40,000
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• DOT specification: DOT 4+
• Chemical Properties: Synthetic
• Capacity [litre]: 1
• Dry Boiling Point [°C]: 265
• Packing Type: Bottle
• Weight [kg]: 1.13
• Manufacturer: VALEO
• Name: VA 402406

• Wet Boiling Point [°C]: 170
• DOT specification: DOT 4, DOT 4 LV
• Dry Boiling Point [°C]: 265
• Capacity [litre]: 1
• Weight [kg]: 1.064
• Observe service information:
• Manufacturer: FEBI

DIN/ISO: ISO 4925 Class 3, ISO 4925 Class 4, ISO 4925 Class 6 General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Quantity per packing unit: 12
• Wet Boiling Point [°C]: 180
• DOT specification: DOT 5.1
• Dry Boiling Point [°C]: 260
• Capacity [litre]: 1
• Specification: FMVSS 116 DOT 5.1, ISO 4925 Classes 4, SAE J 1703
• Weight [kg]: 0.296
• Observe service information:
• Manufacturer: FEBI

DIN/ISO: ISO 4925 Class 3, ISO 4925 Class 4, ISO 4925 Class 5.1 General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Quantity per packing unit: 12
• Wet Boiling Point [°C]: 184
• DOT specification: DOT 5.1
• Dry Boiling Point [°C]: 274
• Capacity [litre]: 1
• Weight [kg]: 0.296
• Observe service information:
• Manufacturer: FEBI

DIN/ISO: ISO 4925 Class 3, ISO 4925 Class 4, ISO 4925 Class 5.1, ISO 4925 Class 6 Specification: FMVSS 116 DOT 5.1, ISO 4925 Classes 4, SAE J 1703, ISO 4925 Classes 6 General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• DOT specification: DOT 4+
• Dry Boiling Point [°C]: 265
• Wet Boiling Point [°C]: 180
• Chemical Properties: Synthetic
• Packing Type: Bottle
• Recommended change interval [years]: 2
• Capacity [litre]: 1
• Recommended change interval [km]: 40,000
• Observe the vehicle manufacturer specifications:
• Observe system fill quantity:
• Length [mm]: 60
• Weight [kg]: 1.15, 1.4
• Height [mm]: 225
• Width [mm]: 115
• DIN/ISO: ISO 4925
• Manufacturer: VAICO

Specification: FMVSS 116 DOT 4, ISO 4925 Class 4, SAE J 1703 / J 1704, FMVSS 116 DOT 3 General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Quantity per packing unit: 4
• Dry Boiling Point [°C]: 260
• Wet Boiling Point [°C]: 160
• DOT specification: DOT 4
• Capacity [litre]: 5
• Weight [kg]: 5.607
• Observe service information:
• Manufacturer: FEBI BILSTEIN
• Lisainfo: 21754 FEBI
• Additional information: 21754 FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• DOT specification: DOT 4
• Chemical Properties: Synthetic
• Capacity [litre]: 5
• Dry Boiling Point [°C]: 245
• Packing Type: Canister
• Manufacturer: VALEO
• Name: VA 402404

• Quantity per packing unit: 4
• Wet Boiling Point [°C]: 180
• DOT specification: DOT 4
• Dry Boiling Point [°C]: 260
• DIN/ISO: ISO 4925
• Capacity [litre]: 5
• Specification: MB 331.0
• Weight [kg]: 5.607
• Observe service information:
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Quantity per packing unit: 4
• DOT specification: DOT 4, DOT 4 LV
• Wet Boiling Point [°C]: 170
• Dry Boiling Point [°C]: 265
• Capacity [litre]: 5
• Weight [kg]: 5.32
• Observe service information:
• Manufacturer: FEBI-UKLAD HAMULCOWY

DIN/ISO: ISO 4925 Class 3, ISO 4925 Class 4, ISO 4925 Class 6 General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• DOT specification: DOT 4+
• Dry Boiling Point [°C]: 265
• Wet Boiling Point [°C]: 180
• Chemical Properties: Synthetic
• Capacity [litre]: 5
• Recommended change interval [years]: 2
• Packing Type: Canister
• Recommended change interval [km]: 40,000
• Observe the vehicle manufacturer specifications:
• Observe system fill quantity:
• Width [mm]: 115
• Length [mm]: 300
• Height [mm]: 230
• Weight [kg]: 4.72
• DIN/ISO: ISO 4925
• Manufacturer: VAICO

Specification: ISO 4925 Class 4, SAE J 1703 / J 1704, FMVSS 116 DOT 3, FMVSS 116 DOT 4 General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Quantity per packing unit: 4
• Wet Boiling Point [°C]: 180
• DOT specification: DOT 5.1
• Dry Boiling Point [°C]: 260
• Capacity [litre]: 5
• Specification: FMVSS 116 DOT 5.1, ISO 4925 Classes 4, SAE J 1703
• Weight [kg]: 0.296
• Observe service information:
• Manufacturer: FEBI

DIN/ISO: ISO 4925 Class 3, ISO 4925 Class 4, ISO 4925 Class 5.1 General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Specification: FMVSS 116 DOT 4, ISO 4925 class 4
• DOT specification: DOT 4

• DOT specification: DOT 4

Specification: BMW/Mini 83 13 0 139, FMVSS 116 DOT 4, ISO 4925 class 6, Saab 93165410, SAE J1704, VW 501.14