• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Engine Code: B5244T
• Line insulation design: with silicone-coated woven-fibre insulation
• Cable Length [mm]: 600
• Number of circuits: 4
• Socket colour: grey
• Number of pins: 4
• Weight [kg]: 0.169
• Length [mm]: 725
• for OE number: 12 79 9169
• Connector Shape: rectangular
• Thread Size: M18 x 1,5
• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Exhaust System: after catalytic converter
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Lambda Sensor
• Voltage [V]: 12
• Number of circuits: 4
• Weight [kg]: 0.09
• Resistor [Ohm]: 9
• Operating Mode: Electric
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY
• Name: CE 09SKV909

• Construction Year to: 07.1998
• Line insulation design: with silicone-coated woven-fibre insulation
• Number of pins: 4
• Socket colour: black
• Number of circuits: 4
• Connector Shape: rectangular
• Cable Length [mm]: 730
• Thread Size: M18 x 1,5
• Weight [kg]: 0.013
• for OE number: 993 606 127 01
• Length [mm]: 850
• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Exhaust System: after catalytic converter
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year from: 08.1998
• Lambda Sensor: Diagnostic Probe, Heated
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: MAX
• Lisainfo: MGS-615
• Additional information: MGS-615

• Construction Year to: 12.1998
• Supplementary Article/Info 2: for lead-free fuel
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 103
• Gross Weight [g]: 152
• Manufacturer: DENSO
• Name: DN DOX-0117
• Quality class: Q

Lambda Sensor: Regulating Probe, Heated, Finger probe, Lambda Sensor Additional information: "Tootja: DENSO
A4 AVANT (8D5, B5),
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
A4 AVANT (8D5, B5),
(kvaliteediklass: Q)"

• Construction Year to: 07.1998
• Lambda Sensor: Regulating Probe, Planar probe, Heated
• Engine Code: B 5254 T
• Cable Length [mm]: 550
• Manufacturer: DELPHI
• Name: DE ES20255-12B1

• Lambda Sensor: Heated
• Length [mm]: 500
• Number of pins: 4
• Technical Information Number: Universal 77004
• Manufacturer: FAE

• Construction Year from: 07.1998
• Lambda Sensor: Diagnostic Probe
• Exhaust System: after catalytic converter
• Fitting Position: Front
• Length [mm]: 770
• Number of connectors: 4
• Manufacturer: VERNET

• Construction Year from: 08.1998
• Lambda Sensor: Diagnostic Probe, Heated, Thread pre-greased
• Fitting Position: after catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Conductor Number: 4
• Connector Shape: angular
• Thread Size: 18x1,5
• Length [mm]: 400
• Number of circuits: 4
• Version: ZR PLANAR
• Weight [kg]: 0.163
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year from: 08.1998, 07.1998
• Catalytic Converter Type: with three-way catalytic converter
• Fitting Position: after catalytic converter
• Block Separation:
• Lambda Sensor: Diagnostic Probe, Planar probe, Heated
• Cable Length [mm]: 680
• Manufacturer: DELPHI
• Name: DE ES20341-12B1

• Construction Year from: 08.1998
• Lambda Sensor: Diagnostic Probe
• Voltage [V]: 12
• Length [mm]: 765
• Number of circuits: 4
• Weight [kg]: 0.15
• Resistor [Ohm]: 9
• Operating Mode: Electric
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY
• Name: CE 09SKV639

• Construction Year from: 08.1998
• Lambda Sensor: Diagnostic Probe, Unheated
• Exhaust System: after catalytic converter
• Number of pins: 4
• Cable Length [mm]: 540
• Quality: OE EQUIVALENT
• Manufacturer: MEAT&DORIA

• Construction Year to: 09.1998
• Line insulation design: with silicone-coated woven-fibre insulation
• Conductor Number: 4
• Cable Length [mm]: 630
• Thread Size: M18x1,5
• Length [mm]: 670
• Number of connectors: 4
• Housing Colour: black
• Lambda Sensor: Heated, Thread pre-greased
• Weight [kg]: 0.142
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: B 5254 T
• Model Year to: 1998
• Line insulation design: with silicone-coated woven-fibre insulation
• Number of pins: 4
• for OE number: V99760001
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Length [mm]: 350
• Exhaust System: after catalytic converter
• Manufacturer: VEMO GERMANY

Lambda Sensor: Regulating Probe, Finger probe, Heated, Thread pre-greased Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 06.1998
• Fitting Position: Front, before catalytic converter
• Lambda Sensor: Regulating Probe, Heated, Thread pre-greased
• Line insulation design: with silicone-coated woven-fibre insulation
• Number of pins: 4
• Number of circuits: 4
• Socket colour: green
• Connector Shape: rectangular
• Thread Size: M18 x 1,5
• Weight [kg]: 0.138
• for OE number: 96 369 687 80
• Cable Length [mm]: 500
• Length [mm]: 600
• Number of connectors: 4
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year from: 12.1996
• Construction Year to: 12.1998
• Fitting Position: before catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Lambda Sensor: Planar probe, Heated, Thread pre-greased
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Manufacturer: VEMO GERMANY

Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year from: 08.1998
• Lambda Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Engine Code: B 5254 T
• Construction Year from: 07.1998
• Fitting Position: after catalytic converter
• Cable Length [mm]: 250
• Conductor Number: 4
• Number of circuits: 4
• Name: EP 1.998.235
• Manufacturer: EPS

Lambda Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased

• Construction Year from: 01.1999
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 93
• Gross Weight [g]: 140
• Manufacturer: DENSO
• Name: DN DOX-0150
• Quality class: Q

Lambda Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
(kvaliteediklass: Q)"

• Lambda Sensor: Lambda Sensor
• Cable Length [mm]: 510
• Number of circuits: 4
• Manufacturer: ERA

• Construction Year from: 08.1998
• Lambda Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 665
• Available as universal article as well, see article no.: 0258986615
• Recommended change interval [km]: 160,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Construction Year from: 01.1999
• for OE number: 9497345, 1367825
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 770
• Number of pins: 4
• Weight [g]: 131
• Gross Weight [g]: 164
• Manufacturer: DENSO
• Name: DN DOX-2021

Lambda Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
C70 I COUPE, 03.97-0
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
C70 I COUPE, 03.97-0
(kvaliteediklass: Q)"

• Construction Year to: 07.1998
• Lambda Sensor: Regulating Probe, Planar probe, Thread pre-greased
• Fitting Position: Exhaust Manifold
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 400
• Number of pins: 4
• Weight [kg]: 0.124
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 09.1998
• Lambda Sensor: Diagnostic Probe, Heated, Thread pre-greased
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 660
• Weight [kg]: 0.012
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Lambda Sensor
• Voltage [V]: 12
• Colour: red
• Number of circuits: 5
• Weight [kg]: 0.15
• Operating Mode: Electric
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY
• Name: CE 09SKV905

• Construction Year from: 07.1998
• Fitting Position: Front
• Line insulation design: with silicone-coated woven-fibre insulation
• Number of pins: 4
• Number of circuits: 4
• Socket colour: black
• Connector Shape: angular
• Weight [kg]: 0.142
• for OE number: 8 631 668
• Thread Size: M18 x 1,5
• Length [mm]: 650
• Lambda Sensor: Heated, Diagnostic Probe, Thread pre-greased
• Version: ZR-PLANAR
• Exhaust System: after catalytic converter
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year from: 07.1998
• Lambda Sensor: Regulating Probe, Lambda Sensor, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 600
• Manufacturer: DELPHI

• Lambda Sensor: Regulating Probe, Lambda Sensor
• Construction Year from: 08.1998
• Voltage [V]: 12
• Length [mm]: 500
• Number of circuits: 5
• Weight [kg]: 0.15
• Operating Mode: Electric
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY
• Name: CE 09SKV862

• Lambda Sensor: Lambda Sensor
• Voltage [V]: 12
• Length [mm]: 580
• Number of circuits: 5
• Weight [kg]: 0.16
• Operating Mode: Electric
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY
• Name: CE 09SKV853

• Construction Year to: 06.1998
• Lambda Sensor: Regulating Probe, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 530
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PA358103391
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Lambda Sensor: Lambda Sensor
• Weight [kg]: 0.15
• Warranty: 3 years warranty
• Technical Information: Universal
• Name: CE 09SKV915
• Manufacturer: ESEN SKV