• Fabrication Number: ECP-AR-013
• Manufacturer: NTY

• Switch Pressure [bar]: 0.5
• Thread Size: M14x1.5
• Sensor Type: Closed-type Sensor
• Manufacturer: VERNET
• Additional information: OS3561 VERNET
• Lisainfo: OS3561 VERNET

• Engine Code: B 5234 FT
• Pressure [bar]: 1
• Thread Size: M14x1,5
• Spanner Size: 24
• Name: EP 1.800.056
• Manufacturer: EPS

• Thread Size: M 14x1,5
• Manufacturer: FAE

• Switch point from [bar]: 0.4
• Switch point to [bar]: 0.6
• External Thread Size: M14 x 1,5
• Spanner Size: 24
• Number of connectors: 1
• Colour: brown
• Weight [kg]: 0.04
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Switch point from [bar]: 0.4
• Switch point to [bar]: 0.6
• External Thread Size: M14 x 1,5
• Spanner Size: 24
• Number of connectors: 1
• Colour: brown
• Weight [kg]: 0.04
• Supplementary Article/Info 2: with seal ring
• Manufacturer: SWAG
• Name: SW 55 91 5076

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Sensor Type: Passive sensor
• for OE number: 9118368
• Manufacturer: KAMOKA

• Number of pins: 1
• Switch pressure from [bar]: 0.39
• Switch pressure to [bar]: 0.58
• Thread Size: M 14 x 1,5
• Colour: black
• Supplementary Article/Supplementary Info: with gaskets/seals
• Manufacturer: METZGER

• Engine Code: B 5234 FT
• Thread Size: M14 x 1,5
• Switch Pressure [bar]: 0.5
• Spanner Size: 24
• Number of pins: 1
• Weight [kg]: 0.05
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 3
• Colour: black
• Material: Plastic
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Number of pins: 3
• Operating Mode: Mechanical
• Manufacturer: DELPHI
• Name: DE SS10992-12B1

• Alternatively:
• Supplementary Article/Supplementary Info: with seal
• Number of pins: 3
• Supplementary Article/Info 2: without cable
• Connector Shape: rectangular
• Weight [kg]: 0.024
• Alternative Repair Kit: 550144
• Manufacturer: ERA

• Number of connectors: 3
• Manufacturer: VERNET

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Number of pins: 2
• Cable Length [mm]: 110
• Socket colour: black
• Spanner Size: 19
• Thread Size: M10x1
• for OE number: 7439186486
• Supplementary Article/Info 2: with seal ring
• Manufacturer: NRF

• Number of pins: 2
• Connector Shape: rectangular
• Socket colour: black
• Cable Length [mm]: 310
• Sensor Type: Inductive Sensor
• for OE number: 74 33 547 699, 3547699
• Manufacturer: MEAT&DORIA

Manufacturer: FAE

Manufacturer: MAGNETI MARELLI

Manufacturer: MAGNETI MARELLI

• Construction Year from: 01.1994
• Engine Code: B5234FT
• Resistor [Ohm]: 300
• Cable Length [mm]: 310
• Sensor Type: Inductive Sensor
• Colour: white
• Supplementary Article/Info 2: for crankshaft
• Number of pins: 2
• Number of connectors: 2
• Rated Voltage [V]: 12
• Fitting Depth [mm]: 32
• Housing Colour: black
• Weight [kg]: 0.087
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

Manufacturer: MAGNETI MARELLI

• for OE number: 9 186 486
• Thread Size: M10
• Number of pins: 2
• Supplementary Article/Info 2: with cable
• Switch point from [°C]: 80
• Switch point to [°C]: 25
• Weight [kg]: 0.032
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: B 5234 FT
• Thread Size: M10x1
• Spanner Size: 19
• Name: EP 1.830.110
• Manufacturer: EPS

• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Colour: black
• Cable Length [mm]: 285
• Number of pins: 2
• Weight [kg]: 0.04
• Resistor [Ohm]: 300
• Fitting Depth [mm]: 32
• Manufacturer: ERA

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Operating Mode: Mechanical
• Manufacturer: MAXGEAR

• Length [mm]: 150
• External Thread Size: M10 x 1
• Spanner Size: 19
• Number of connectors: 2
• Colour: black
• Weight [kg]: 0.03
• Name: SW 55 92 7206
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Cable Length [mm]: 143
• Number of pins: 2
• Connecting thread: M10 x 1
• Manufacturer: ERA

• Construction Year from: 09.1993
• Manufacturer: BOSCH
• Name: BS 0280122001

• Number of pins: 2
• Connector Shape: oval
• Socket colour: black
• Cable Length [mm]: 140
• Thread Size: M10x1 mm
• Sensor Type: NTC Sensor
• Spanner Size: 19 mm
• for OE number: 74 39 186 486, 3545031, 9186486
• Manufacturer: MEAT&DORIA

• Mounting Type: Bolted
• Voltage [V]: 12
• Resistor [Ohm]: 2,200, 257
• Supplementary Article/Supplementary Info: with seal
• Temperature range from [°C]: 25
• Temperature range to [°C]: 80
• Thread Size: M10x1
• Sensor Type: NTC Sensor
• Number of pins: 2
• Supplementary Article/Info 2: with cable
• Housing Colour: black
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead
• Name: HE 6PT009107281
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Length [mm]: 215
• Number of pins: 3
• Manufacturer: DELPHI
• Name: DE SS11148

• Length [mm]: 160
• Number of pins: 3
• Weight [kg]: 0.09
• Manufacturer: ERA

• Construction Year from: 01.1996
• Transmission Code: AW50-42
• Number of pins: 2
• Cable Length [mm]: 180
• Housing Colour: grey
• Manufacturer: FAE

• Number of pins: 3
• Connector Shape: rectangular
• Socket colour: white
• Number of mounting bores: 2
• Sensor Type: Hall Sensor
• for OE number: 74 39 146 108, 1383966
• Manufacturer: MEAT&DORIA

• Engine Code: B 5234 FT
• Sensor Type: NTC Sensor
• Thread Size: M10x1
• Spanner Size: 19
• Supplementary Article/Info 2: with seal ring
• Number of pins: 2
• Manufacturer: MEYLE

• Supplementary Article/Info 2: with potentiometer
• Manufacturer: METZGER

• Voltage [V]: 12
• Resistor [Ohm]: 300
• Cable Length [mm]: 315
• Sensor Type: Inductive Sensor
• Number of pins: 2
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Construction Year from: 09.1994
• Construction Year to: 07.1996
• Lambda Sensor: Regulating Probe
• Exhaust System: before catalytic converter
• Engine Code: B 5234 FT
• Number of circuits: 4
• Supplementary Article/Info 2: without plug
• Manufacturer: ENERGY

• Transmission Type: Automatic Transmission
• Transmission Code: AW50-42
• Number of pins: 2
• Cable Length [mm]: 450
• Housing Colour: black
• Manufacturer: FAE

• Number of pins: 2
• Cable Length [mm]: 310
• Housing Colour: black
• Manufacturer: FAE

• Lambda Sensor: Regulating Probe, Lambda Sensor
• Construction Year from: 09.1994
• Construction Year to: 07.1996
• Exhaust System: before catalytic converter
• Voltage [V]: 12
• Length [mm]: 630
• Number of circuits: 4
• Weight [kg]: 0.11
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV042

• Line insulation design: with silicone-coated woven-fibre insulation
• Number of pins: 4
• Socket colour: black
• Number of circuits: 4
• Connector Shape: rectangular
• Cable Length [mm]: 730
• Thread Size: M18 x 1,5
• Weight [kg]: 0.013
• for OE number: 993 606 127 01
• Length [mm]: 850
• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Exhaust System: after catalytic converter
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year from: 09.1993
• Quality class: PJ
• Name: Air flow sensor

• Construction Year from: 09.1993
• Construction Year to: 07.1996
• Number of pins: 4
• Housing Type: with housing
• Lisainfo: Air Mass Sensor
• Additional information: Air Mass Sensor

• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 103
• Gross Weight [g]: 152
• Manufacturer: DENSO
• Name: DN DOX-0117
• Quality class: Q

Lambda Sensor: Regulating Probe, Heated, Finger probe, Lambda Sensor Additional information: "Tootja: DENSO
A4 AVANT (8D5, B5),
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
A4 AVANT (8D5, B5),
(kvaliteediklass: Q)"

• Cable Length [mm]: 550
• Lambda Sensor: Planar probe, Heated
• Manufacturer: DELPHI

• Construction Year from: 09.1994
• Construction Year to: 07.1996
• Lambda Sensor: Regulating Probe, Heated
• Supplementary Article/Info 2: for leaded fuel
• Fitting Position: before catalytic converter
• Length [mm]: 500
• Number of pins: 4
• Technical Information Number: Universal 77004
• Manufacturer: FAE

• for OE number: 000 540 3917
• Cable Length [mm]: 750
• Number of pins: 4
• Lambda Sensor: Heated
• Manufacturer: TRUCKTEC AUTOMOTIVE

• Weight [kg]: 0.116
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Heated
• Cable Length [mm]: 640
• Manufacturer: FAST

• Line insulation design: with silicone-coated woven-fibre insulation
• Conductor Number: 4
• Cable Length [mm]: 630
• Thread Size: M18x1,5
• Length [mm]: 670
• Number of connectors: 4
• Housing Colour: black
• Lambda Sensor: Heated, Thread pre-greased
• Weight [kg]: 0.142
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Front, before catalytic converter
• Lambda Sensor: Regulating Probe, Heated, Thread pre-greased
• Line insulation design: with silicone-coated woven-fibre insulation
• Number of pins: 4
• Number of circuits: 4
• Socket colour: green
• Connector Shape: rectangular
• Thread Size: M18 x 1,5
• Weight [kg]: 0.138
• for OE number: 96 369 687 80
• Cable Length [mm]: 500
• Length [mm]: 600
• Number of connectors: 4
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year from: 08.1994
• Fitting Position: before catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Lambda Sensor: Planar probe, Heated, Thread pre-greased
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Manufacturer: VEMO GERMANY

Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year from: 09.1993, 09.1994
• Lambda Sensor: Regulating Probe, Diagnostic Probe
• Supplementary Article/Info 2: for lead-free fuel, for leaded fuel
• Block Separation:
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: BS 0258986505
• Manufacturer: BOSCH

Fitting Position: before catalytic converter, after catalytic converter

• Housing Colour: black
• Number of pins: 3
• Manufacturer: FAE

• Lambda Sensor: Lambda Sensor
• Cable Length [mm]: 510
• Number of circuits: 4
• Manufacturer: ERA

• Construction Year from: 09.1993
• Construction Year to: 07.1996
• Manufacturer: MEAT&DORIA

• Construction Year from: 09.1993
• Construction Year to: 07.1996
• Lambda Sensor: Regulating Probe, Planar probe, Thread pre-greased
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 400
• Number of pins: 4
• Weight [kg]: 0.124
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Diagnostic Probe, Heated, Thread pre-greased
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 660
• Weight [kg]: 0.012
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 3
• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: with cable
• Length [mm]: 180
• Manufacturer: FAE

• Number of pins: 3
• Cable Length [mm]: 160
• Sensor Type: Hall Sensor
• Manufacturer: METZGER

• Operating Mode: Electric
• Manufacturer: MAGNETI MARELLI

• Construction Year from: 09.1993, 09.1994
• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Supplementary Article/Info 2: for lead-free fuel
• Block Separation:
• Number of circuits: 4
• Overall Length [mm]: 530
• Available as universal article as well, see article no.: 0258986505
• Recommended change interval [km]: 160,000
• Manufacturer: BOSCH

• Voltage [V]: 12
• Length [mm]: 160
• Sensor Type: Hall Sensor
• Number of pins: 3
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Construction Year from: 09.1993
• Manufacturer: BOSCH

• Lambda Sensor: Regulating Probe, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 530
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PA358103391
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.