• Bearing Type: Angular Ball Bearing
• Fitting Position: Front Axle Left, Front Axle Right
• Manufacturer: JP GROUP
• Lisainfo: PAKENDIS 10 tk
• Additional information: PAKENDIS 10 tk

• Fitting Position: Front Axle Left, Front Axle Right
• for OE number: 7201592
• Manufacturer: GSP

• Inner Diameter [mm]: 14
• Fitting Position: Front Axle
• Required quantity: 2
• Weight [kg]: 0.056
• Name: Laager,amorditugilaager
• Manufacturer: TED

• Suspension: for vehicles with electronic suspension control
• for PR number: G53
• Fabrication Number: AD-VW-010
• Fitting Position: Front Axle Left, Front Axle Right
• Manufacturer: NTY

• Fitting Position: Front Axle
• for OE number: 1J0412249
• Manufacturer: SASIC

• Width [mm]: 13.5
• Weight [kg]: 0.08
• Bearing Type: Angular Ball Bearing
• Inner Diameter [mm]: 14
• Outer Diameter [mm]: 45
• Material: Plastic
• Required quantity: 2
• Fitting Position: Front Axle
• General Information: deep groove ball thrust bearing; front
• Manufacturer: VIKA

• Fitting Position: Front Axle
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Quantity per packing unit: 10
• Fitting Position: Front Axle Left, Front Axle Right
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Mounting Type: Rubber-Metal Mount
• Fitting Position: mounting
• Quality class: PJ
• Name: Top mount left, right

• Suspension: for vehicles with electronic suspension control
• for PR number: G53, G54
• Block Separation:
• Width [mm]: 13.5
• Inner Diameter [mm]: 14
• Outer Diameter [mm]: 45
• Material: Plastic
• Bearing Type: Angular Ball Bearing
• Fitting Position: Front Axle Left, Front Axle Right
• Weight [kg]: 0.08
• Manufacturer: FEBI BILSTEIN
• Additional information: FE01111
• Lisainfo: FE01111

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Suspension: for vehicles with electronic suspension control
• for PR number: G53, G54
• Block Separation:
• Width [mm]: 14
• Inner Diameter [mm]: 14
• Outer Diameter [mm]: 45
• Material: Plastic
• Bearing Type: Angular Ball Bearing
• Fitting Position: Front Axle Left, Front Axle Right
• Weight [kg]: 0.08
• Manufacturer: BLUE PRINT ZAWIESZENIE

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Suspension: for vehicles with electronic suspension control
• for PR number: G53, G54
• Block Separation:
• Width [mm]: 13.5
• Inner Diameter [mm]: 14
• Outer Diameter [mm]: 45
• Material: Plastic
• Bearing Type: Angular Ball Bearing
• Fitting Position: Front Axle Left, Front Axle Right
• Weight [kg]: 0.08
• Name: SW 30 54 0001
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Front Axle Left, Front Axle Right
• for OE number: 1J0 412 331 B
• Manufacturer: GSP

• Vehicle Identification Number (VIN) from: 6R-F-000 001
• Fitting Position: Front Axle
• Suspension: for vehicles with electronic suspension control
• Quantity per axle: 2
• Name: Laager - K„„ndmik VW
• Manufacturer: SKF

• Fitting Position: Front Axle
• SVHC: No SVHC present!
• Name: Vedruamordi tugilaager
• Manufacturer: FAG

• Fitting Position: Front Axle, Front Axle Left, Front Axle Right
• Supplementary Article/Info 2: with bearing
• Fabrication Number: AD-VW-006
• Manufacturer: NTY
• Name: NTY AD-VW-006

• Fitting Position: Front Axle both sides
• Outer Diameter [mm]: 45
• Inner Diameter [mm]: 14
• Material: Plastic
• for OE number: 1J0 412 249
• Name: Top mount left=right
• Quality class: PJ

Lisainfo: "Tootja: SRL
VW POLO/SEAT INCA
(kvaliteediklass: PJ)" Additional information: "Tootja: SRL
VW POLO/SEAT INCA
(kvaliteediklass: PJ)"

• Fitting Position: Front Axle
• Manufacturer: KAMOKA AMORTYZATORY

• Fitting Position: Front Axle Left, Front Axle Right
• Quantity per axle: 2
• for OE number: 6R0 412 249
• Manufacturer: LMI

Name: Laager - K„„ndmik AUDI A1 10- SEAT IBIZA V 08-, TOLEDO 12-

• Fitting Position: Front Axle
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Fitting Position: Front Axle
• Weight [kg]: 0.237
• Required quantity: 2
• Thickness [mm]: 54
• Inner Diameter [mm]: 26
• Outer Diameter [mm]: 83
• Material: Rubber/Metal
• Supplementary Article/Info 2: without ball bearing
• General Information: Shock absorber top rubber; front
• Manufacturer: VIKA

• Fitting Position: Front Axle Left, Front Axle Right
• Height [mm]: 53
• Inner Diameter [mm]: 26
• Supplementary Article/Info 2: with ball bearing
• Manufacturer: BGA

• Fitting Position: Front Axle Left, Front Axle Right
• Manufacturer: GSP

• Inner Diameter [mm]: 26
• Height [mm]: 54
• Outer Diameter [mm]: 83
• Material: Rubber/Metal
• Fitting Position: Front Axle Left, Front Axle Right
• Weight [kg]: 0.237
• Supplementary Article/Info 2: without ball bearing
• Observe service information:
• Name: Laager - K„„ndmik. VW P. GOLF 4
• Manufacturer: FEB
• Additional information: FE09227
• Lisainfo: FE09227

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Front Axle Left, Front Axle Right
• Quantity per axle: 2
• for OE number: 6R0 412 249
• Name: Laager,amorditugilaager
• Manufacturer: SAA

• Mounting Type: Rubber Mount
• Fitting Position: Front Axle
• for OE number: 1J0412331C
• Manufacturer: SASIC

• for PR number: 1JA, 1JB, 1JP, 1JS
• Fitting Position: Rear Axle
• Manufacturer: MAX

Name: Laager - K„„ndmik. VW T. BORA/GOLF 4/FABIA/A2/OCTAVIA 96- LE/PR

• Fitting Position: Rear Axle
• Inner Diameter [mm]: 11
• Fabrication Number: AD-VW-018
• Manufacturer: NTY
• Name: NTY AD-VW-018

• Height [mm]: 54
• Inner Diameter [mm]: 26
• Outer Diameter [mm]: 83
• Material: Rubber/Metal
• Fitting Position: Front Axle Left, Front Axle Right
• Weight [kg]: 0.237
• Supplementary Article/Info 2: without ball bearing
• Name: SW 30 54 0012
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Quantity per axle: 2
• Fitting Position: Front Axle Left, Front Axle Right
• Supplementary Article/Info 2: without ball bearing
• Alternative Repair Kit: 802 270, 802 697
• for OE number: 1J0 412 331, 1J0 412 331 B, 1J0 412 331 C
• Name: Laager - K„„ndmik. VW P. GOLF 4 9
• Manufacturer: SAA

• Quantity per axle: 2
• Fitting Position: Front Axle Left, Front Axle Right
• Supplementary Article/Info 2: without ball bearing
• Alternative Repair Kit: 25346 01, 36957 01
• for OE number: 1J0 412 331, 1J0 412 331 B, 1J0 412 331 C
• Name: Laager - K„„ndmik. VW P. GOLF 4 (BEZ O½YSKA)
• Manufacturer: LMI

• Fitting Position: Front Axle
• SVHC: No SVHC present!
• Name: LU 815008930
• Manufacturer: FAG

• Fabrication Number: AD-VV-005
• Manufacturer: NTY

Fitting Position: Rear Axle, Front Axle Left, Front Axle Right, Front Axle

• Weight [kg]: 0.237
• Fitting Position: Front Axle
• Thickness [mm]: 54
• Required quantity: 2
• Inner Diameter [mm]: 26
• Outer Diameter [mm]: 83
• Material: Rubber/Metal
• Supplementary Article/Info 2: without ball bearing
• General Information: Shock absorber top rubber; front
• Manufacturer: BORSEHUNG

• Weight [kg]: 0.28
• Fitting Position: Rear Axle
• Required quantity: 2
• Manufacturer: TEDGUM

• Fitting Position: Rear Axle
• Manufacturer: KAMOKA AMORTYZATORY

• Fitting Position: Front Axle
• Weight [kg]: 0.237
• Required quantity: 2
• Thickness [mm]: 54
• Inner Diameter [mm]: 26
• Outer Diameter [mm]: 83
• Material: Rubber/Metal
• Supplementary Article/Info 2: without ball bearing
• General Information: Shock absorber rubber kit; front
• Manufacturer: VIKA

• Fitting Position: Front Axle
• General Information: deep groove ball thrust bearing; front
• Manufacturer: BORSEHUNG

• Inner Diameter [mm]: 10.2
• Fitting Position: Lower, Rear Axle both sides
• Required quantity: 2
• Weight [kg]: 0.087
• Outer Diameter [mm]: 43
• Name: Kinnitus,amordid
• Manufacturer: TED

• Fitting Position: Front Axle Left, Front Axle Right
• Material: Rubber/Metal
• Supplementary Article/Info 2: with bearing
• Required quantity: 2
• Height [mm]: 53
• Outer Diameter [mm]: 83
• Centering Diameter [mm]: 14.2
• Manufacturer: TRW

for OE number: 1J0 412 249, 1J0 412 331 B, 1J0 412 331 C, 357 412 249 A, 6K0 413 031 B

• Suspension: for vehicles with electronic suspension control
• for PR number: G53, G54
• Block Separation:
• Inner Diameter [mm]: 26
• Outer Diameter [mm]: 83
• Material: Rubber/Metal
• Fitting Position: Front Axle
• Weight [kg]: 0.41
• Supplementary Article/Info 2: with ball bearing
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. Name: Laager - K„„ndmik. VW P. GOLF 4 98- KPL. Z O½YSKIEM I —RUB¤

• for PR number: 1JA, 1JB, 1JP, 1JS
• Fitting Position: Rear Axle
• Name: Laager - K„„ndmik. VW T. GOLF 4/B
• Manufacturer: MAX

• Fitting Position: Front Axle Left, Front Axle Right
• for OE number: 1J0 513 353 A
• Manufacturer: GSP ZAWIESZENIE

• Fitting Position: Front Axle Left, Front Axle Right
• Material: Rubber/Metal
• Supplementary Article/Info 2: without bearing
• Fabrication Number: AD-VV-003
• Manufacturer: NTY

• Fitting Position: Front Axle
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Suspension: for vehicles with electronic suspension control
• for PR number: G53, G54
• Block Separation:
• Inner Diameter [mm]: 26
• Outer Diameter [mm]: 83
• Material: Rubber/Metal
• Fitting Position: Front Axle
• Weight [kg]: 0.41
• Supplementary Article/Info 2: with ball bearing
• Name: SW 30 93 7878
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Name: Suspension strut support bearing left=right
• Quality class: PJ

Lisainfo: "Tootja: SRL
AUDI A3/OCTAVIA
(kvaliteediklass: PJ)"

• Quantity per axle: 2
• Fitting Position: Front Axle Left, Front Axle Right
• Manufacturer: LMI

Name: Laager - K„„ndmik. VW P. GOLF 4 98- KPL. Z O½YSKIEM

• Fitting Position: Front Axle
• Technical Information: Suspension mounting + separated suspension bearing
• Manufacturer: KYB

Name: Laager - K„„ndmik. FORD P. GALAXY/ SEAT ALHAMBRA, CORDOBA, IBIZA II, INCA, TOLEDO/ VW CADDY II, CORRADO, GOLF III, IV, PASSAT, POLO, SHARAN,

• Name: Suspension strut support bearing left=right
• Quality class: PJ

Lisainfo: "Tootja: SRL
AUDI A3/TT/SKODA
(kvaliteediklass: PJ)"

• for PR number: 1JA, 1JB, 1JP, 1JS
• Fitting Position: Rear Axle Left, Rear Axle Right
• Quantity per axle: 2
• for OE number: 1J0 513 353 B, 6R0 513 353, 6R0 513 353 B
• Supplementary Article/Supplementary Info: Rolling Bearing is not required
• Manufacturer: LMI

Name: Laager - K„„ndmik. VW T. BORA/GOLF 4/FABIA/A2/OCTAVIA 96- LE/PR

• Fitting Position: Front Axle Left, Front Axle Right
• Supplementary Article/Info 2: with ball bearing
• Outer Diameter [mm]: 83
• Quantity per axle: 2
• Manufacturer: METZGER

• for PR number: 1JA, 1JB, 1JP, 1JS
• Fitting Position: Rear Axle Left, Rear Axle Right
• Quantity per axle: 2
• for OE number: 1J0 513 353 B, 6R0 513 353, 6R0 513 353 B
• Supplementary Article/Supplementary Info: Rolling Bearing is not required
• Name: Vedruamordi tugilaager
• Manufacturer: SAA

• Fitting Position: Front Axle
• Weight [kg]: 0.4
• Supplementary Article/Info 2: with rolling bearing
• Guarantee: 5 years guarantee
• Packaging length [cm]: 8.1
• Packaging width [cm]: 8.1
• Packaging height [cm]: 9
• Manufacturer: MONROE

• Fitting Position: Rear Axle
• Weight [kg]: 0.28
• Required quantity: 2
• Material: Aluminium, Rubber/Metal
• General Information: Shock absorber upper cover
• Manufacturer: VIKA

• Fitting Position: Rear Axle
• Weight [g]: 280
• General Information: Shock absorber upper cover
• Manufacturer: BORSEHUNG
• Additional information: 1J0513353G BOR
• Lisainfo: 1J0513353G BOR

• Fitting Position: Rear Axle
• Technical Information: Suspension mounting only (no bearing)
• Manufacturer: KYB

Name: Laager - K„„ndmik. AUDI T. A1, A2, A3, TT/ SEAT CORDOBA, IBIZA IV, V, LEON/ SKODA FABIA, OCTAVIA, ROOMSTER/ VW BORA, FOX, GOLF IV, NEW BEETL

• Vehicle Identification Number (VIN) from: 6R-F-000 001
• Fitting Position: Front Axle
• Suspension: for vehicles with electronic suspension control
• Quantity per axle: 2
• General Information: SKF recommends always changing in pairs both sides
• Name: Vedruamordi tugilaager
• Manufacturer: SKF

• Fitting Position: Rear Axle
• Weight [kg]: 0.3
• Supplementary Article/Info 2: without bearing
• Guarantee: 5 years guarantee
• Packaging length [cm]: 13.6
• Packaging width [cm]: 11.8
• Packaging height [cm]: 11.4
• Manufacturer: MONROE

• Vehicle Identification Number (VIN) from: 6R-F-000 001
• Fitting Position: Rear Axle
• Suspension: for vehicles with sports suspension
• Quantity per axle: 2
• General Information: SKF recommends always changing in pairs both sides
• Name:
• Manufacturer: SKF

• Fitting Position: Front Axle Left, Front Axle Right
• Quantity per axle: 2
• Manufacturer: LEMFORDER

• Fitting Position: Front Axle
• Quantity per axle: 2
• Alternative Repair Kit: 108 561
• Mounting Type: Rubber-Metal Mount
• Supplementary Article/Info 2: without rolling bearing
• General Information: Shock absorber rubber kit; front
• Manufacturer: BORSEHUNG

• Fitting Position: Rear Axle
• Inner Diameter [mm]: 11
• Outer Diameter [mm]: 61
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Fitting Position: Front Axle
• Weight [kg]: 0.237
• Required quantity: 2
• Thickness [mm]: 54
• Inner Diameter [mm]: 26
• Outer Diameter [mm]: 83
• Material: Rubber/Metal
• Supplementary Article/Info 2: without ball bearing
• General Information: Rubber and dust cover kit
• Manufacturer: VIKA

• Fitting Position: Front Axle
• Weight [kg]: 0.237
• Required quantity: 2
• Thickness [mm]: 54
• Inner Diameter [mm]: 26
• Outer Diameter [mm]: 83
• Material: Rubber/Metal
• Supplementary Article/Info 2: without ball bearing
• General Information: Rubber and dust cover kit
• Manufacturer: VIKA