• Fitting Position: frontal sided
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Width [mm]: 10
• Material: FPM (fluoride rubber)
• Manufacturer: JP GROUP A/S
• Lisainfo: Oil seal, 35x48x10 mm
• Additional information: Oil seal, 35x48x10 mm

• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Thickness [mm]: 11
• Material: FPM (fluoride rubber)/ACM (polyacrylate rubber)
• Lisainfo: Oil seal for crankshaft, 85x105x11 mm
• Additional information: Oil seal for crankshaft, 85x105x11 mm

• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Width 1 [mm]: 9
• Width 2 [mm]: 11
• Housing Type: with housing
• Lisainfo: Seal flange for crankshaft
• Additional information: Seal flange for crankshaft

• Fitting Position: frontal sided
• Weight [kg]: 0.016
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Material: ACM (Polyacrylate)
• Required quantity: 1
• Thickness [mm]: 10
• General Information: seal ring;35*48*10 mm
• Manufacturer: VIKA

• Fitting Position: frontal sided
• General Information: seal ring
• Manufacturer: VIKA

• Fitting Position: frontal sided
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Swirl Type: Right-hand Twist
• Radial Shaft Seal Design: ASW
• Manufacturer: DR MOTOR PRZEWODY PRZELEWOWE
• Name: DRM 01967

• Fitting Position: Rear, Front
• Required quantity: 2
• Height 1 [mm]: 10
• Outer Diameter 1 [mm]: 47
• Inner Diameter 1 [mm]: 32
• Material: FPM (fluoride rubber)
• for OE number: 026103085D
• Swirl Type: Alternating Twist
• Dust Cover: with dust lip
• Name: VOLLI RONGASTIHEND, NUKKVOLL
• Manufacturer: COT
• Additional information: 12012709
• Lisainfo: 12012709

• Fitting Position: Front
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Fabrication Number: NUP-VW-012
• Manufacturer: NTY

• Fitting Position: frontal sided
• Required quantity: 2
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Width [mm]: 10
• SVHC: No SVHC present!
• Manufacturer: INA
• Name: LU 413009310

• Required quantity: 2
• Fitting Position: frontal sided
• Engine Code: DV
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Radial Shaft Seal Design: A SL
• Swirl Type: Alternating Twist
• Name: VOLLI RONGASTIHEND, NUKKVOLL
• Manufacturer: REI
• Lisainfo: 81-19299-10
• Additional information: 81-19299-10

• Required quantity: 2
• Fitting Position: frontal sided, transmission sided
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Radial Shaft Seal Design: ASW
• Swirl Type: Alternating Twist
• Material: FPM (fluoride rubber)/ACM (polyacrylate rubber)
• Dust Cover: with dust lip
• Alternative Repair Kit: 325.156
• Manufacturer: ELRING
• Lisainfo: 325.155 ELR
• Additional information: 325.155 ELR

• Fitting Position: frontal sided, transmission sided
• Height [mm]: 11
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Swirl Type: Left-hand Twist
• Dust Cover: with dust lip
• Manufacturer: DELLO AUTOMEGA

• Engine Code: DV
• Engine Number from: 28D007274
• Required quantity: 2
• Block Separation:
• Fitting Position: frontal sided
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Swirl Type: Alternating Twist
• Name: VOLLI RONGASTIHEND, NUKKVOLL
• Manufacturer: AJU

• Required quantity: 2
• Fitting Position: frontal sided, transmission sided
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Radial Shaft Seal Design: ASW
• Swirl Type: Alternating Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Alternative Repair Kit: 325.155
• Manufacturer: ELRING

• Fitting Position: frontal sided
• Engine Code: DV
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Radial Shaft Seal Design: A SL
• Swirl Type: Right-hand Twist
• Name: VOLLI RONGASTIHEND, VŽNTVOLL
• Manufacturer: REI

• Fitting Position: frontal sided
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Radial Shaft Seal Design: ASW
• Swirl Type: Right-hand Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Manufacturer: ELRING

• Fitting Position: frontal sided
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Radial Shaft Seal Design: ASW
• Swirl Type: Right-hand Twist
• Material: FPM (fluoride rubber)/ACM (polyacrylate rubber)
• Dust Cover: with dust lip
• Manufacturer: ELRING

• Engine Code: DV
• Quantity per packing unit: 10
• Fitting Position: frontal sided
• Weight [kg]: 0.035
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: frontal sided
• General Information: shaft oil seal
• Manufacturer: BORSEHUNG

• Fitting Position: Axle beam
• General Information: shaft oil seal
• Manufacturer: BORSEHUNG

• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 11
• Radial Shaft Seal Design: ASW
• Swirl Type: Left-hand Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Alternative Repair Kit: 829.056
• Manufacturer: ELRING
• Lisainfo: 342.093 ELR
• Additional information: 342.093 ELR

• Fitting Position: transmission sided
• Engine Code: DV
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 11
• Radial Shaft Seal Design: A SL
• Swirl Type: Left-hand Twist
• Height 1 [mm]: 9
• Name: VOLLI RONGASTIHEND, VŽNTVOLL
• Manufacturer: REI
• Lisainfo: 81-23708-40
• Additional information: 81-23708-40

• Thickness [mm]: 11
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Material: FPM (fluoride rubber)
• Fitting Position: transmission sided
• Weight [kg]: 0.058
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Quantity per packing unit: 5
• Thickness [mm]: 11
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Fitting Position: transmission sided
• Weight [kg]: 0.103
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: frontal sided
• Engine Code: DV
• Engine Number from: 28D007274
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Swirl Type: Right-hand Twist
• Name: VOLLI RONGASTIHEND, VŽNTVOLL
• Manufacturer: AJU

• Thickness [mm]: 10
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Fitting Position: frontal sided
• Weight [kg]: 0.01
• Observe service information:
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: frontal sided
• Supplementary Article/Info 2: with mounting sleeve
• Height 1 [mm]: 10
• Outer Diameter 1 [mm]: 48
• Inner Diameter 1 [mm]: 35
• Material: PTFE (polytetrafluoroethylene)
• for OE number: 038103085
• Swirl Type: Right-hand Twist
• Dust Cover: with dust lip
• Name: VOLLI RONGASTIHEND, VŽNTVOLL
• Manufacturer: COT

• Fitting Position: transmission sided
• Engine Code: DV
• Engine Number from: 28D007274
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 12
• Manufacturer: AJUSA

• Fitting Position: transmission sided
• Supplementary Article/Info 2: with flange
• Outer Diameter [mm]: 111
• Inner Diameter [mm]: 85
• Height [mm]: 16
• Manufacturer: DELLO AUTOMEGA

• Supplementary Article/Info 2: with flange
• Fitting Position: transmission sided
• Fabrication Number: NUP-VW-006
• Manufacturer: NTY

• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 11
• Radial Shaft Seal Design: ASW
• Swirl Type: Left-hand Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Supplementary Article/Info 2: with mounting sleeve
• Manufacturer: ELRING

• Fitting Position: transmission sided
• Weight [kg]: 0.17
• Inner Diameter [mm]: 85
• Required quantity: 1
• Supplementary Article/Info 2: with flange
• General Information: sealing flang; rear
• Manufacturer: VIKA

• Quantity per packing unit: 5
• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Weight [kg]: 0.265
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• for OE number: 03G 105 021 C
• Thickness [mm]: 10
• Inner Diameter [mm]: 35
• Fitting Position: frontal sided
• Outer Diameter [mm]: 48
• Weight [kg]: 0.031
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: transmission sided
• Weight [kg]: 0.17
• Inner Diameter [mm]: 85
• Required quantity: 1
• Supplementary Article/Info 2: with flange
• General Information: sealing flang; rear
• Manufacturer: VIKA

• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Radial Shaft Seal Design: SP
• Swirl Type: Left-hand Twist
• Housing Type: with housing
• Supplementary Article/Info 2: with mounting sleeve
• Manufacturer: ELRING
• Lisainfo: 804.850 ELR
• Additional information: 804.850 ELR

Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber) Installation Information: Mounting dry and without any additional oil and grease

• Fitting Position: transmission sided
• Supplementary Article/Info 2: with mounting sleeve
• Height 1 [mm]: 15.7
• Outer Diameter 1 [mm]: 131
• Outer Diameter 2 [mm]: 152
• Inner Diameter 1 [mm]: 85
• Material: PTFE (polytetrafluoroethylene)
• for OE number: 028103171B
• Swirl Type: Alternating Twist
• Name: VOLLI RONGASTIHEND, VŽNTVOLL
• Manufacturer: COT