• Switch Pressure [bar]: 1.4
• Number of connectors: 1
• External Thread [mm]: M10x1
• Colour Coding: black
• Manufacturer: JP GROUP
• Lisainfo: PAKENDIS 10 tk
• Additional information: PAKENDIS 10 tk

• Switch point from [bar]: 0.75
• Switch point to [bar]: 1.05
• Colour Coding: grey
• Number of connectors: 1
• External Thread [mm]: M10x1
• Manufacturer: JP GROUP
• Lisainfo: PAKENDIS 10 tk
• Additional information: PAKENDIS 10 tk

• Number of pins: 4
• Colour Coding: green
• Manufacturer: JP GROUP
• Lisainfo: Sender for water temperature gauge 4 pins
• Additional information: Sender for water temperature gauge 4 pins

• Number of pins: 1
• Thread Size: M10x1 mm
• Spanner Size: 13 mm
• for OE number: 049919563B
• Manufacturer: KAMOKA
• Lisainfo: 4080049 KAMOKA
• Additional information: 4080049 KAMOKA

• Thread Size: M10x1
• Colour: grey
• Number of pins: 1
• Manufacturer: DELLO AUTOMEGA

• Thread Size: M10x1
• Colour: brown
• Number of pins: 1
• Manufacturer: DELLO AUTOMEGA

• Thread Size: M10X1
• Colour: black
• Number of pins: 1
• Manufacturer: DELLO AUTOMEGA

• Length [mm]: 46
• Thread Size: M10x1
• Spanner Size: 24
• Colour Coding: grey
• Number of pins: 1
• Pressure from [bar]: 0.75
• Pressure to [bar]: 1.05
• Diameter [mm]: 2
• Name: OLISURVELšLITUS
• Manufacturer: MAX

• Fabrication Number: ECC-AU-002
• Supplementary Article/Info 2: with seal ring
• Thread Size: M10x1
• Socket colour: grey
• Number of pins: 1

• Connector Shape: D Shape
• Operating Mode: Hydraulic
• Colour Coding: grey
• Thread Size: M 10
• Thread Pitch [mm]: 1
• Number of pins: 1
• Control Range [bar]: 0,75 - 1,05
• Supplementary Article/Info 2: with seal ring
• for OE number: 038 919 081M, 955 606 091 10, 1 469 771
• Manufacturer: TOPRAN HANS PRIES

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Length [mm]: 46
• Thread Size: M10x1
• Spanner Size: 24
• Colour Coding: black
• Pressure from [bar]: 1.2
• Pressure to [bar]: 1.5
• Diameter [mm]: 3
• Name: OLISURVELšLITUS
• Manufacturer: MAX

• General Information: temperature sensor
• Manufacturer: VIKA

• Switch point from [bar]: 0.75
• Switch point to [bar]: 1.05
• External Thread [mm]: M10x1
• Number of connectors: 1
• Colour Coding: grey
• Lisainfo: PAKENDIS 10 tk
• Additional information: PAKENDIS 10 tk

• Engine Code: AFB
• Manufacturer: AIC
• Lisainfo: 51913 AIC
• Additional information: 51913 AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Fabrication Number: ECT-AU-008
• Number of pins: 4
• Manufacturer: NTY

• for OE number: 1100619
• Manufacturer: KAMOKA

• Fabrication Number: ECT-AU-004
• Number of pins: 4
• Colour Coding: green
• Connector Shape: oval
• Manufacturer: NTY

• Vehicle Identification Number (VIN) to: 3BX600000
• Switch Pressure [bar]: 0.9
• Thread Size: M10x1.0
• Sensor Type: Open-style sensor
• Manufacturer: VERNET

• Required quantity: 1
• Engine Code: AKN
• Colour: grey
• Pressure [bar]: 0.9
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Required quantity: 1
• Engine Code: AKN
• Colour: black
• Pressure [bar]: 1.4
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Pressure [bar]: 0.9
• Thread Size: M10 x 1
• Technical Information Number: circuit N.O.
• Manufacturer: ERA

• Thread Size: M10 x 1
• Spanner Size: 14
• Supplementary Article/Supplementary Info: with seal
• Number of pins: 1
• Colour Coding: blue
• Weight [kg]: 0.019
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Alternatively:
• Pressure [bar]: 10.5
• Housing Colour: grey
• Thread Size: M10×1-6g
• Diameter [mm]: 24
• Spanner Size: 24
• Number of pins: 1
• Name: OLISURVELšLITUS
• Manufacturer: DLP
• Lisainfo: SW90007
• Additional information: SW90007

• Thread Size: M10x1,0
• Colour: white
• Weight [kg]: 0.031
• Pressure from [bar]: 0.7
• Pressure to [bar]: 1
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: AKN
• Colour: grey
• Pressure [bar]: 1
• Thread Size: M10x1
• Spanner Size: 24
• Corresponds to the original part in colour: brown
• Name: OLISURVELšLITUS
• Manufacturer: EPS

• Switch point from [bar]: 1.2
• Length [mm]: 46
• Switch point to [bar]: 1.5
• Inner Diameter [mm]: 2.54
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Colour Coding: black
• Surface: Zinc-coated
• Weight [kg]: 0.031
• Supplementary Article/Info 2: with seal ring
• Name: SW 30 23 0003
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of pins: 2
• Weight [kg]: 0.05
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV555

Transmission Type: 5-Speed Manual Transmission, 6-Speed Manual Transmission, 4-Speed Automatic Transmission

• Plug Type: Blade Terminal
• Operating Mode: Hydraulic
• Colour Coding: grey
• Thread Size: M 10
• Thread Pitch [mm]: 1
• Number of pins: 1
• Control Range [bar]: 0,75 - 1,05
• Supplementary Article/Info 2: with seal ring
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Operating Mode: Manual
• Switch Point [°C]: 10
• Number of pins: 2
• Vehicle Equipment: for vehicles with air conditioning
• Lisainfo: Thermo switch for air condition 10/1.7 C
• Additional information: Thermo switch for air condition 10/1.7 C

• Switch Pressure [bar]: 0.9
• Thread Size: M10x1.0
• Sensor Type: Open-style sensor
• Manufacturer: VERNET

• Switch point from [bar]: 1.2
• Length [mm]: 46
• Switch point to [bar]: 1.5
• Inner Diameter [mm]: 2.54
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Colour Coding: black
• Surface: Zinc-coated
• Weight [kg]: 0.031
• Supplementary Article/Info 2: with seal ring
• Name: OLISURVELšLITUS
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Sensor Type: Inductive Sensor
• Number of pins: 3
• Cable Length [mm]: 750
• Manufacturer: ABAKUS DEPO/LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis.

• Colour: black
• Control Range [bar]: 1.2/1.6BAR
• General Information: oil pressure switch
• Manufacturer: BORSEHUNG

• Thread Size: M10x1,0
• Control Range [bar]: 1,2 - 1,6
• Colour: black
• Weight [kg]: 0.028
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Pressure from [bar]: 0.75
• Pressure to [bar]: 1
• Combi Switch Function: Normally Open Contact
• Colour: grey
• Spanner Size: 24
• Thread Size: M10 x 1,0
• Number of pins: 1
• Name: OLISURVELšLITUS
• Manufacturer: MEY

• Switch Pressure [bar]: 1.4
• Thread Size: M10x1
• Supplementary Article/Supplementary Info: with seal
• Colour: black
• Number of pins: 1
• Version: Neue Version
• Manufacturer: METZGER

• Pressure [bar]: 8.5
• Housing Colour: dark-brown
• Thread Size: M10×1-6g
• Diameter [mm]: 24
• Spanner Size: 24
• Number of pins: 1
• Name: OLISURVELšLITUS
• Manufacturer: DLP
• Quality class: PJ

Additional information: "Tootja: DELPHI
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
(kvaliteediklass: PJ)"

• Number of pins: 4
• Colour: green
• Manufacturer: DELLO AUTOMEGA

• Switch point from [bar]: 0.75
• Length [mm]: 46
• Switch point to [bar]: 1.05
• Inner Diameter [mm]: 2.48
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: grey
• Surface: Zinc-coated
• Weight [kg]: 0.031
• Supplementary Article/Info 2: with seal ring
• Manufacturer: SWAG
• Name: SW 30 23 0004

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Temperature range to [°C]: 170
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX

• Pressure [bar]: 10.5
• Housing Colour: grey
• Thread Size: M10×1-6g
• Diameter [mm]: 24
• Spanner Size: 24
• Number of pins: 1
• Name: OLISURVELšLITUS
• Manufacturer: DLP
• Quality class: PJ

Additional information: "Tootja: DELPHI
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
(kvaliteediklass: PJ)"

• Pressure [bar]: 1.4
• Thread Size: M10 x 1
• Number of pins: 1
• Technical Information Number: circuit N.O.
• Manufacturer: ERA

• Engine Code: AKN
• Number of connectors: 4
• Manufacturer: 3RG

• Length [mm]: 46
• Switch point from [bar]: 0.75
• Switch point to [bar]: 1.05
• Inner Diameter [mm]: 2.48
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: grey
• Surface: Zinc-coated
• Weight [kg]: 0.031
• Supplementary Article/Info 2: with seal ring
• Name: OLISURVELšLITUS
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Sensor Type: NTC Sensor
• Mounting Type: Clamped
• Connector Shape: rectangular
• Number of pins: 4
• Socket colour: black
• for OE number: 059919501
• Supplementary Article/Info 2: with mounting parts
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Colour: black
• Plug Type ID: 4
• Weight [kg]: 0.02
• Required quantity: 1
• Outer Diameter [mm]: 20
• Number of connectors: 4
• General Information: temperature sensor; black; 4 pins
• Manufacturer: VIKA

• Housing Colour: black
• Number of pins: 4
• Spanner Size: 0
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: DLP

• Colour: grey
• Sensor Type: Passive sensor
• for OE number: 71957147
• Manufacturer: KAMOKA

• External Thread Size: M10 x 1
• Spanner Size: 22
• Number of connectors: 1
• Colour: grey
• Shifting Points [bar]: 0.9
• Weight [kg]: 0.031
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Sensor Type: NTC Sensor
• Mounting Type: Clamped
• Connector Shape: D Shape
• Number of pins: 4
• for OE number: 059919501A
• Supplementary Article/Info 2: with mounting parts
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• External Thread Size: M10 x 1
• Spanner Size: 22
• Number of connectors: 1
• Colour: grey
• Shifting Points [bar]: 0.9
• Weight [kg]: 0.031
• Supplementary Article/Info 2: with seal ring
• Manufacturer: SWAG
• Name: SW 30 91 9016

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Cable Length [mm]: 745
• Fabrication Number: ECP-AU-021
• Manufacturer: NTY

• Connector Shape: D Shape
• Material: Plastic
• Number of pins: 4
• Plug Type: Female
• Sensor Type: NTC Sensor
• Spanner Size: not have
• Thread Size: not have
• Manufacturer: NISSENS
• Name: NI 207009

Technical Information: FIRST FIT - a time-saving installation! Find all additional parts such as O-rings, clip, washer in the box.

• Construction Year to: 01.2003
• Tightening torque from [Nm]: 20
• Voltage [V]: 12
• Combi Switch Function: Normally Open Contact
• Current Strength [A]: 0.25
• Tolerance [%]: 15
• Thread Size: M10x1
• Spanner Size: 24
• Pressure from [bar]: 0.75
• Pressure to [bar]: 1.05
• Number of pins: 1
• Plug Type: Blade Terminal
• Corresponds to the original part in colour: grey
• Assy./disassy. by qualified personnel required!:
• Name: HE 6ZL003259481
• Manufacturer: HELLA

• Number of pins: 4
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX

• Colour: green
• Plug Type ID: 4
• Weight [kg]: 0.02
• Required quantity: 1
• Outer Diameter [mm]: 20
• Number of connectors: 4
• General Information: temperature sensor; green; 4 pins
• Manufacturer: VIKA

• Thread Size: 20 mm
• Number of pins: 4
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: VER

• Colour Coding: green
• Connector Shape: oval
• Sensor Type: NTC Sensor
• Number of pins: 4
• for OE number: 059 919 501A, 1 124 770
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Vehicle Identification Number (VIN) from: 3B-Y-000001
• Thread Size: M 10x1
• Housing Colour: black
• Pressure [bar]: 1.4
• Manufacturer: FAE

• Number of connectors: 4
• Weight [kg]: 0.038
• Supplementary Article/Supplementary Info: with seal, with retaining spring
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: FEB
• Additional information: FE32510
• Lisainfo: FE32510

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: AKN
• Colour: grey
• Pressure to [bar]: 1.05
• Pressure from [bar]: 0.75
• Pressure [bar]: 1
• Thread Size: M10x1
• Spanner Size: 24
• Name: OLISURVELšLITUS
• Manufacturer: EPS

• for OE number: 078 919 501 C
• Manufacturer: TRUCKTEC

• Number of connectors: 4
• Weight [kg]: 0.038
• Supplementary Article/Supplementary Info: with seal, with retaining spring
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: AKN
• Housing Colour: green
• Corresponds to the original part in colour: black
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Voltage [V]: 12
• Combi Switch Function: Normally Open Contact
• Thread Size: M10x1
• Colour: grey
• Spanner Size: 24
• Pressure from [bar]: 0.75
• Pressure to [bar]: 1.05
• Number of pins: 1
• Corresponds to the original part in colour: grey
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

• Voltage [V]: 12
• Number of pins: 4
• Weight [kg]: 0.02
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Required quantity: 1
• Engine Code: AKN
• Number of pins: 4
• Supplementary Article/Info 2: with seal ring
• Colour: green
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Sensor Type: NTC Sensor
• Supplementary Article/Info 2: without seal ring
• Colour: green
• Number of pins: 4
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MEY

• Country Specific Design: Mexico
• Manufacturer: DELLO AUTOMEGA

• Engine Code: AKN
• Operating Mode: Mechanical
• Number of pins: 2
• Combi Switch Function: Normally Open Contact
• Colour: blue
• Material: Plastic
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• External Thread Size: M10 x 1
• Number of connectors: 1
• Weight [kg]: 0.01
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

Manufacturer: MAGNETI MARELLI

• Pressure from [bar]: 0.75
• Pressure to [bar]: 1.05
• Combi Switch Function: Normally Open Contact
• Colour: grey
• Spanner Size: 24
• Thread Size: M10 x 1,0
• Number of pins: 1
• Name: OLISURVELšLITUS
• Manufacturer: MEY

• External Thread Size: M10 x 1
• Number of connectors: 1
• Weight [kg]: 0.01
• Supplementary Article/Info 2: with seal ring
• Name: SW 30 93 3825
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of pins: 2
• Connector Shape: rectangular
• Socket colour: black
• Thread Size: M10x1 mm
• Sensor Type: NTC Sensor
• Spanner Size: 19
• for OE number: 059 919 563
• Manufacturer: MEAT&DORIA

• Number of pins: 4
• Manufacturer: ERA

• Vehicle Identification Number (VIN) from: 3B-Y-000 001
• Number of pins: 4
• Colour: green
• Supplementary Article/Supplementary Info: with seal
• Quality: IAM
• Article number of recommended accessories: 0905458
• Power [W]: 0.06
• Manufacturer: METZGER

• Thread Size: 20
• Number of pins: 4
• Manufacturer: ERA

• Construction Year to: 01.2003
• Engine Code: AKN
• Voltage [V]: 12
• Length [mm]: 730
• Number of pins: 3
• Weight [kg]: 0.11
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 17SKV265
• Manufacturer: ESEN SKV