• Lambda Sensor: Regulating Probe, Thread pre-greased
• Thread Size: M18x1.5
• Cable Length [mm]: 880
• Number of circuits: 4
• Fitting Position: before catalytic converter
• Fabrication Number: ESL-AU-013
• Manufacturer: NTY

• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Lambda Sensor: Diagnostic Probe
• Cable Length [mm]: 970
• Exhaust System: after catalytic converter
• Conductor Number: 4
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV126

• Lambda Sensor: Lambda Sensor
• Voltage [V]: 12
• Number of circuits: 4
• Weight [kg]: 0.09
• Resistor [Ohm]: 9
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV909

• Engine Code: BWK
• Vehicle Identification Number (VIN) from: 5N-9-070001
• Lambda Sensor: Diagnostic Probe
• Number of circuits: 4
• Supplementary Article/Info 2: without plug
• Manufacturer: ENERGY

• Engine Code: CAVA, CTHA
• Construction Year from: 03.2008
• Construction Year to: 12.2016
• Lambda Sensor: Diagnostic Probe, Finger probe
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Transmission Type: Manual Transmission
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Engine Code: BWK
• Construction Year to: 10.2008
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 103
• Gross Weight [g]: 152
• Manufacturer: DENSO
• Name: DN DOX-0119
• Quality class: Q

Lambda Sensor: Regulating Probe, Heated, Finger probe, Lambda Sensor Additional information: "Tootja: DENSO
ESCORT VII SEDAN (GA
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
ESCORT VII SEDAN (GA
(kvaliteediklass: Q)"

• Construction Year from: 11.2007
• Construction Year to: 11.2008
• Lambda Sensor: Diagnostic Probe
• Voltage [V]: 12
• Length [mm]: 681
• Number of circuits: 4
• Weight [kg]: 0.13
• Resistor [Ohm]: 6
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV672

• Resistor [Ohm]: 9
• Conductor Number: 4
• Length [mm]: 721
• Number of circuits: 4
• Cable Length [mm]: 721
• Lambda Sensor: Heated
• Name: LAMBDA ANDUR
• Manufacturer: MAG

• Construction Year to: 10.2008
• Lambda Sensor: Diagnostic Probe, Heated
• Voltage [V]: 12
• Length [mm]: 595
• Number of circuits: 4
• Weight [kg]: 0.13
• Resistor [Ohm]: 6
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV712

• Engine Code: BWK
• Construction Year to: 11.2008
• Fitting Position: Exhaust Manifold
• Line insulation design: with silicone-coated woven-fibre insulation
• Connector Shape: D Shape
• for OE number: 03C 906 262 T
• Weight [kg]: 0.131
• Thread Size: M18 x 1,5
• Number of circuits: 4
• Socket colour: brown
• Overall Length [mm]: 400
• Number of pins: 4
• Number of connectors: 4
• Lambda Sensor: Regulating Probe, Thread pre-greased
• Exhaust System: before catalytic converter
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year from: 10.2007
• Vehicle Identification Number (VIN) from: 5N-9-070 000, 5N-9-010 000
• Fitting Position: before catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Lambda Sensor: Planar probe, Heated, Thread pre-greased
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Manufacturer: VEMO GERMANY

Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: BWK
• Construction Year from: 12.2008
• Vehicle Identification Number (VIN) from: 5N_9_070001
• Fitting Position: after catalytic converter
• Length [mm]: 480
• Cable Length [mm]: 750
• Conductor Number: 4
• Available as universal article as well, see article no.: 1.998.235
• Number of circuits: 4
• Name: LAMBDA ANDUR
• Manufacturer: EPS

Lambda Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased

• Engine Code: CAVA
• Construction Year from: 05.2011
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 93
• Gross Weight [g]: 140
• Manufacturer: DENSO
• Name: DN DOX-0150
• Quality class: Q

Lambda Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
(kvaliteediklass: Q)"

• Engine Code: BWK
• Fitting Position: Front
• Construction Year to: 05.2008
• Line insulation design: with silicone-coated woven-fibre insulation
• Weight [kg]: 0.142
• Number of circuits: 4
• Connector Shape: D Shape
• Thread Size: M18 x 1,5
• for OE number: 036 906 262 AA
• Socket colour: brown
• Length [mm]: 520
• Number of pins: 4
• Number of connectors: 4
• Housing Colour: brown
• Lambda Sensor: Regulating Probe, Thread pre-greased
• Exhaust System: before catalytic converter
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: CAVA, CTHA
• Construction Year from: 03.2008
• Construction Year to: 12.2016
• Lambda Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Lambda Sensor: Lambda Sensor
• Weight [kg]: 0.2
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Construction Year from: 05.2011
• Engine Code: CAVA
• Lambda Sensor: Diagnostic Probe, Planar probe, Thread pre-greased
• Fitting Position: after catalytic converter
• Transmission Type: Manual Transmission
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 570
• Number of pins: 4
• Weight [kg]: 0.18
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: BWK
• Construction Year to: 11.2008
• Fitting Position: after catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 555
• Number of pins: 4
• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Weight [kg]: 0.141
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: CAVA, CTHA
• Construction Year from: 03.2008
• Construction Year to: 12.2016
• Lambda Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 750
• Available as universal article as well, see article no.: 0258986602
• Recommended change interval [km]: 160,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Engine Code: BWK
• Construction Year to: 10.2008
• for OE number: 03C906262AC, 036906262AA
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 620
• Number of pins: 4
• Weight [g]: 107
• Gross Weight [g]: 138
• Manufacturer: DENSO
• Quality class: Q
• Name: Lambda sensor

Lambda Sensor: Regulating Probe, Heated, Finger probe, Lambda Sensor

• Engine Code: CAVA
• Construction Year from: 05.2011
• for OE number: 022906262AB
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 800
• Number of pins: 4
• Weight [g]: 111
• Gross Weight [g]: 144
• Manufacturer: DENSO
• Name: Lambda sensor
• Quality class: Q

Lambda Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
A6 (4F2, C6), 05.04-
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
A6 (4F2, C6), 05.04-
(kvaliteediklass: Q)"

• Lambda Sensor: Regulating Probe, Heated
• Engine Code: BWK
• Vehicle Identification Number (VIN) to: 5N-9-010000, 070000
• Fitting Position: before catalytic converter
• Length [mm]: 520
• Number of pins: 4
• Socket colour: brown
• Technical Information Number: Universal 77004
• Manufacturer: FAE

• Construction Year from: 11.2007
• Construction Year to: 09.2015
• Engine Code: CAVA,CTHA
• Fitting Position: before catalytic converter
• Lambda Sensor: Planar probe, Thread pre-greased, Heated
• Number of pins: 4
• Cable Length [mm]: 750
• Thread Size: M18x1,5
• Switch Pressure [bar]: 4
• Weight [kg]: 0.17
• Manufacturer: VALEO
• Name: VA 368024

• Construction Year from: 03.2008
• Construction Year to: 12.2016
• Lambda Sensor: Regulating Probe, Heated
• Resistor [Ohm]: 4.9
• Length [mm]: 800
• Conductor Number: 5
• Number of circuits: 5
• Cable Length [mm]: 800
• Manufacturer: MAGNETI MARELLI

• Engine Code: BWK
• Production date to: 31.10.2008
• Lambda Sensor: Regulating Probe
• Number of pins: 4
• Length [mm]: 600
• Housing Colour: brown
• Manufacturer: METZGER

• Engine Code: BWK
• Vehicle Identification Number (VIN) to: 5N-9-010000, 070000
• Connector Shape: D Shape
• Socket colour: black
• Number of circuits: 4
• Cable Length [mm]: 550
• Weight [kg]: 0.149
• for OE number: 03C 906 262 R
• Thread Size: M18 x 1,5
• Length [mm]: 650
• Number of pins: 4
• Number of connectors: 4
• Housing Colour: black
• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Exhaust System: after catalytic converter
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Lambda Sensor
• Voltage [V]: 12
• Colour: red
• Number of circuits: 5
• Weight [kg]: 0.15
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV905

• Construction Year from: 11.2008
• Lambda Sensor: Regulating Probe, Broadband lambda sensor, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 615
• Name: DE ES21368-12B1
• Manufacturer: DELPHI

• Engine Code: BWK, CAVA, CTHA
• Construction Year from: 11.2008
• Lambda Sensor: Regulating Probe, Heated
• Fitting Position: before catalytic converter
• Number of circuits: 5
• Length [mm]: 800
• Name: Lambda andur
• Manufacturer: MAX

• Construction Year from: 11.2008
• Lambda Sensor: Regulating Probe, Broadband lambda sensor
• Fitting Position: before catalytic converter
• Cable Length [mm]: 800
• Number of pins: 6
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead
• Name: Lambda andur
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Engine Code: BWK
• Construction Year from: 11.2008
• Fitting Position: before catalytic converter
• Colour: grey
• Length [mm]: 750
• Cable Length [mm]: 735
• Conductor Number: 5
• Supplementary Article/Info 2: with fastening material
• Number of circuits: 5
• Name: EP 1.998.374
• Manufacturer: EPS

Lambda Sensor: Regulating Probe, Heated, Planar probe, Broadband lambda sensor, Thread pre-greased

• Lambda Sensor: Diagnostic Probe
• Number of pins: 4
• Cable Length [mm]: 970
• for OE number: 04E 906 262 CH
• Quality: OE EQUIVALENT
• Manufacturer: MEAT&DORIA

• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Warranty: 5 years warranty
• General Information: Sold in Hueco brand: printing and packaging
• Manufacturer: HUCO

• Lambda Sensor: Lambda Sensor
• Weight [kg]: 0.15
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Technical Information: Universal
• Manufacturer: SKV GERMANY

• Fitting Position: Front
• Lambda Sensor: Finger probe
• General Information: lambda probe; front
• Manufacturer: VIKA

• Engine Code: CAVA, CTHA
• Construction Year from: 03.2008
• Construction Year to: 12.2016
• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 5
• Overall Length [mm]: 750
• Recommended change interval [km]: 250,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Length [mm]: 800
• Number of pins: 6
• Socket colour: black
• Manufacturer: FAE

• Engine Code: CAVA
• Construction Year from: 03.2008
• Lambda Sensor: Diagnostic Probe
• Number of circuits: 4
• Cable Length [mm]: 750
• Manufacturer: METZGER