• Fitting Position: Intake Manifold
• Connector Shape: rectangular
• Number of pins: 2
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Number of pins: 2
• Connector Shape: rectangular
• Fabrication Number: ECT-RE-000
• Manufacturer: NTY

• Fitting Position: Suction Pipe
• Connector Shape: rectangular
• Number of pins: 2
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Engine Code: D4F 732
• Fitting Position: Upper, Lower
• Corresponds to the original part in colour: brown, green
• Name: ANDUR,SISENDOHU TEMPERATUUR
• Manufacturer: EPS
• Additional information: 1-994-005
• Lisainfo: 1-994-005

• Fitting Position: Lower
• Manufacturer: VERNET
• Additional information: AS0006 VERNET
• Lisainfo: AS0006 VERNET

• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: D4F 732
• Pressure from [kPA]: 20
• Pressure to [kPA]: 100
• Name: OHUSURVEANDUR,
• Manufacturer: MAX

• Fitting Position: Upper, Lower
• Number of pins: 2
• for manufacturer number: 6PT 009 109-221
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PT009109221
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Connector Shape: oval
• Number of pins: 3
• for OE number: 8200 719 629
• Manufacturer: TOPRAN HANS PRIES

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Required quantity: 1
• Name: CZUJNIK CI—N. POWIETRZA RENAULT CLIO 2,0 16V 00-
• Manufacturer: BRM

• Engine Code: D4F 732
• Housing Colour: black
• Thread Size: M12x1,5
• Spanner Size: 21
• Manufacturer: FACET

• Measuring Range from [kPa]: 20
• Measuring Range to [kPa]: 100
• Measuring Range from [V]: 0.52
• Measuring Range to [V]: 4.75
• Number of connectors: 3
• Manufacturer: VERNET
• Additional information: MS0119 VERNET
• Lisainfo: MS0119 VERNET

• Engine Code: D4F 732
• Housing Colour: black
• Thread Size: M12x1,5
• Spanner Size: 21
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Number of pins: 2
• Supplementary Article/Info 2: without cable
• Connector Shape: rectangular
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Oxygen Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Diameter [mm]: 12.6
• Manufacturer: VALEO

• Engine Code: D4F 732
• Thread Size: M12x1,25
• Spanner Size: 24
• Manufacturer: FACET

• Engine Code: D4F 732
• Thread Size: M12x1,25
• Spanner Size: 24
• Name: DETONATSIOONIANDUR
• Manufacturer: EPS

• Oxygen Sensor: Regulating Probe
• Number of circuits: 4
• Manufacturer: KAMOKA

• Engine Code: D4F 732
• Number of pins: 3
• Name: Andur,ohuvotu rohk
• Manufacturer: MEY

• Engine Code: D4F 732
• Pressure from [kPA]: 20
• Pressure to [kPA]: 100
• Output Voltage, from [V]: 0.52
• Output Voltage, up to [V]: 4.78
• Manufacturer: FACET

• Engine Code: D4F 732
• Pressure from [kPA]: 20
• Pressure to [kPA]: 100
• Output Voltage, from [V]: 0.52
• Output Voltage, up to [V]: 4.78
• Name: ANDUR,KOMPRESSORIROHK
• Manufacturer: EPS

• Vehicle type: B8J3/B8MG/B8MP/B8MU, B8MY
• Fitting Position: Front
• Oxygen Sensor: Regulating Probe
• Number of connectors: 4
• Length [mm]: 475
• Manufacturer: VERNET

• Vehicle type: B8J3/B8MG/B8MP/B8MU, B8MY
• Fitting Position: Front
• Oxygen Sensor: Diagnostic Probe
• Number of connectors: 4
• Length [mm]: 475
• Manufacturer: VERNET

• Colour: black
• Number of pins: 2
• Weight [kg]: 0.052
• Manufacturer: ERA

• Guarantee: 3 years guarantee
• Weight [kg]: 0.17
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV611

• Number of pins: 2
• Name: DETONATSIOONIANDUR
• Manufacturer: DLP

• Engine Code: D4F 732
• Oxygen Sensor: Regulating Probe, Finger probe
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Transmission Type: Manual Transmission
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Oxygen Sensor: Diagnostic Probe, Planar probe, Heated
• Version: 1
• Fitting Position: after catalytic converter
• for model code: B8J3/B8MG/B8MP/B8MU
• Cable Length [mm]: 450
• Manufacturer: DELPHI ELEKTRONIKA

• Engine Code: D4F 732
• Oxygen Sensor: Diagnostic Probe, Heated
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Length [mm]: 424
• Name: Lambda andur
• Manufacturer: MAX

• Supplementary Article/Info 2: without cable
• Supplementary Article/Supplementary Info: with gasket/seal
• Number of pins: 3
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead
• Manufacturer: HELLA
• Name: HE 6PP009400281

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Construction Year from: 07.2015
• Construction Year to: 11.2020
• Name: DETONATSIOONIANDUR
• Manufacturer: VAL

• Engine Code: D4F 732
• Fitting Position: after catalytic converter
• alternative OE number: 1
• for type code: B8J3/B8MG/B8MP/B8MU, B8MY
• Colour: black
• Cable Length [mm]: 450
• Conductor Number: 4
• Supplementary Article/Info 2: with fastening material
• Available as universal article as well, see article no.: 10.7008
• Number of circuits: 4
• Manufacturer: FACET

Oxygen Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased

• Engine Code: D4F 732
• Fitting Position: after catalytic converter
• alternative OE number: 1
• for type code: B8J3/B8MG/B8MP/B8MU, B8MY
• Colour: black
• Cable Length [mm]: 450
• Conductor Number: 4
• Supplementary Article/Info 2: with fastening material
• Available as universal article as well, see article no.: 1.997.008
• Number of circuits: 4
• Name: EP 1.998.169
• Manufacturer: EPS

Oxygen Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased

• Construction Year to: 12.2018
• Oxygen Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• for OE number: 82 00 632 270
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Engine Code: D4F 732
• Fitting Position: before catalytic converter
• for type code: B8J3/B8MG/B8MP/B8MU, B8MY
• Cable Length [mm]: 450
• Conductor Number: 4
• Supplementary Article/Info 2: with fastening material
• Available as universal article as well, see article no.: 10.7007
• Number of circuits: 4
• Manufacturer: FACET

Oxygen Sensor: Regulating Probe, Heated, Planar probe, Thread pre-greased

• Engine Code: D4F 732
• Fitting Position: before catalytic converter
• for type code: B8J3/B8MG/B8MP/B8MU, B8MY
• Cable Length [mm]: 450
• Conductor Number: 4
• Supplementary Article/Info 2: with fastening material
• Available as universal article as well, see article no.: 1.997.007
• Number of circuits: 4
• Name: LAMBDA ANDUR
• Manufacturer: EPS

Oxygen Sensor: Regulating Probe, Heated, Planar probe, Thread pre-greased

• Oxygen Sensor: Regulating Probe, Broadband oxygen sensor, Heated
• Fitting Position: before catalytic converter
• for model code: B8J3/B8MG
• Cable Length [mm]: 395
• Manufacturer: DELPHI ELEKTRONIKA

• Fuel Type: Petrol
• Number of pins: 3
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 2
• Tightening Torque [Nm]: 22
• Spanner Size: 24
• Thread Size: M12 x 1,25
• Sensor Type: Piezoelectric Sensor
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PG009108881
• Manufacturer: HELLA

SVHC: 1317-36-8; Lead monoxide (lead oxide), 12060-00-3; Lead titanium trioxide, 7439-92-1; Lead Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Oxygen Sensor: Diagnostic Probe, Heated
• alternative OE number: 1
• Fitting Position: after catalytic converter
• for type code: B8J3/B8MG/B8MP/B8MU, B8MY
• Cable Length [mm]: 365
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Name: LAMBDA ANDUR
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Oxygen Sensor: Diagnostic Probe, Planar probe, Heated
• Version: 2
• Fitting Position: after catalytic converter
• for model code: B8J3
• Cable Length [mm]: 435
• Name: DE ES21214-12B1
• Manufacturer: DELPHI

• for type code: B8J3/B8MG/B8MP/B8MU, B8MY
• Number of pins: 4
• Cable Length [mm]: 450
• Thread Size: M18x1,5
• Switch Pressure [bar]: 4
• Connector Shape: rectangular
• Manufacturer: VALEO
• Name: VA 368052

Oxygen Sensor: Regulating Probe, Planar probe, Thread pre-greased, Heated Fitting Position: before catalytic converter, after catalytic converter

• not for OE number: 8201035691
• Fitting Position: before catalytic converter
• Oxygen Sensor: Regulating Probe
• Cable Length [mm]: 390
• Length [mm]: 514
• Number of circuits: 5
• Manufacturer: METZGER

• Number of mounting bores: 2
• Number of pins: 6
• Left-/right-hand drive vehicles: for left-hand drive vehicles
• Transmission Type: not for dual-clutch transmission
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Vehicle Equipment: for vehicles without cruise control
• Number of mounting bores: 2
• Number of pins: 6
• Transmission Type: Manual Transmission
• Left-/right-hand drive vehicles: for left-hand drive vehicles
• Assy./disassy. by qualified personnel required!:
• Name: ANDUR, SOIDUPEDAALIASEND
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Vehicle Equipment: for vehicles with cruise control
• Number of mounting bores: 2
• Number of pins: 6
• Transmission Type: Automatic Transmission
• Left-/right-hand drive vehicles: for left-hand drive vehicles
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PV009978711
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Voltage [V]: 12
• Fitting Position: before catalytic converter
• Cable Length [mm]: 890
• Number of pins: 5
• Guarantee: 3 years guarantee
• Weight [kg]: 0.33
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Fitting Position: before catalytic converter
• Voltage [V]: 12
• for OE number: 227906887R
• Name: NOx-sensor, NOx-katalsaator
• Manufacturer: MD