• Construction Year to: 09.1995
• Number of pins: 2
• Colour: blue
• Lisainfo: Temperature sensor for cooling system, 2 pins
• Additional information: Temperature sensor for cooling system, 2 pins

• Length [mm]: 50
• Housing Colour: blue
• Spanner Size: 19
• Manufacturer: KAMOKA

• Number of pins: 4
• Colour: black
• Lisainfo: Temperature sensor for cooling system
• Additional information: Temperature sensor for cooling system

Fabrication Number: ECT-BM-010

• Construction Year to: 09.1995
• Length [mm]: 53
• Temperature range to [°C]: 130
• Thread Size: M14x1,5
• Spanner Size: 19
• Colour: black
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX

• Length [mm]: 68
• Housing Colour: black
• Spanner Size: 22
• Manufacturer: KAMOKA

• Construction Year to: 09.1995
• Spanner Size: 19
• Colour: blue
• Number of pins: 2
• Thread Size: M12x1,5
• Length [mm]: 51
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX
• Lisainfo: 21-0124
• Additional information: 21-0124

• Construction Year from: 09.1995
• Length [mm]: 68
• Spanner Size: 22
• Colour: black
• Number of pins: 4
• Thread Size: M12x1,5
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX

• Construction Year to: 09.1995
• Connector Shape: rectangular
• Supplementary Article/Info 2: with seal ring
• Colour Coding: blue
• Thread Size: M 12
• Thread Pitch [mm]: 1.5
• Number of pins: 2
• Switch Point [°C]: 140
• Sensor Type: NTC Sensor
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Thread Size: M12 x 1,5
• Spanner Size: 19
• Number of pins: 2
• Colour Coding: blue
• Weight [kg]: 0.035
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year from: 09.1995
• Connector Shape: round
• Sensor Type: NTC Sensor
• Thread Size: M 12
• Thread Pitch [mm]: 1.5
• Number of pins: 2
• Manufacturer: TOPRAN HANS PRIES

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Thread Size: M12x1.5
• Spanner Size: 19
• Manufacturer: FAST

• Construction Year to: 09.1995
• Connector Shape: rectangular
• Sensor Type: NTC Sensor
• Number of pins: 2
• Thread Size: M 14 x 1,5
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Construction Year from: 10.1995
• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: round
• Number of pins: 4
• Socket colour: black
• Spanner Size: 22
• Thread Size: M12x1.5
• for OE number: 13621703993
• Supplementary Article/Info 2: with seal ring
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: rectangular
• Number of pins: 2
• Socket colour: black
• Spanner Size: 19
• Thread Size: M14x1.5
• for OE number: 12621710535
• Manufacturer: NRF

• Construction Year to: 09.1995
• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: rectangular
• Number of pins: 2
• Spanner Size: 19
• Thread Size: M12x1.5
• for OE number: 195321101000
• Supplementary Article/Info 2: with seal ring
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Construction Year from: 10.1995
• Thread Size: M12x1.5
• Manufacturer: VERNET

• Construction Year to: 09.1995
• Length [mm]: 53
• Temperature range to [°C]: 130
• External Thread Size: M14 x 1,5
• Spanner Size: 19
• Number of connectors: 2
• Colour: black
• Screw length below head [mm]: 27
• Weight [kg]: 0.025
• Supplementary Article/Info 2: with seal ring
• Name: SW 20 92 8354
• Manufacturer: SWAG
• Lisainfo: 20 92 8354 SWA
• Additional information: 20 92 8354 SWA

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thread Size: M12 x 1,5
• Spanner Size: 19
• Number of pins: 2
• Connector Shape: rectangular
• Manufacturer: ERA

• Thread Size: M14 x 1,5
• Spanner Size: 19
• Number of pins: 2
• Supplementary Article/Info 2: with seal ring
• Socket colour: black
• Manufacturer: ERA

• Construction Year to: 09.1995
• Length [mm]: 53
• Temperature range to [°C]: 130
• External Thread Size: M14 x 1,5
• Spanner Size: 19
• Number of connectors: 2
• Colour: black
• Screw length below head [mm]: 27
• Weight [kg]: 0.025
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thread Size: M12x1.5
• Manufacturer: VERNET

• Engine Code: M43 B18 (184E2)
• Colour: blue
• Thread Size: M12x1,5
• Spanner Size: 19
• for article number: 1.880.113, 1.880.114, 1.880.149, 1.880.151
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Construction Year to: 09.1995
• Length [mm]: 50.7
• External Thread Size: M12 x 1,5
• Thread Length [mm]: 11
• Spanner Size: 19
• Number of connectors: 2
• Colour: blue
• Colour Coding: blue
• Switch Point [°C]: 20
• Weight [kg]: 0.022
• Supplementary Article/Info 2: with seal ring
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of pins: 4
• Weight [kg]: 0.3
• Packaging length [cm]: 12
• Packaging width [cm]: 8
• Packaging height [cm]: 6
• for OE number: 13621703993, MEK000020, MEK100160A

• Construction Year to: 03.1996
• Number of pins: 2
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Housing Colour: blue
• Number of pins: 2
• Thread Size: M12X1.5-6g
• Spanner Size: 19
• Manufacturer: DELPHI
• Name: DE TS10250

• Construction Year to: 09.1995
• Length [mm]: 50.7
• External Thread Size: M12 x 1,5
• Thread Length [mm]: 11
• Spanner Size: 19
• Number of connectors: 2
• Colour: blue
• Colour Coding: blue
• Switch Point [°C]: 20
• Weight [kg]: 0.022
• Supplementary Article/Info 2: with seal ring
• Manufacturer: SWAG
• Name: SW 40 91 7695
• Lisainfo: 40 91 7695 SWA
• Additional information: 40 91 7695 SWA

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Construction Year to: 03.1996
• Vehicle Equipment: for vehicles with headlamp cleaning system
• Weight [kg]: 0.016
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: M43 B18 (184E2)
• Sensor Type: NTC Sensor
• Thread Size: M12 x 1,5
• Spanner Size: 19
• Colour: blue
• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MEY

• Mounting Type: Bolted
• Voltage [V]: 12
• Resistor [Ohm]: 5,000, 544
• Supplementary Article/Supplementary Info: with seal
• Temperature range from [°C]: 25
• Temperature range to [°C]: 80
• Thread Size: M14x1,5
• Colour: black
• Sensor Type: NTC Sensor
• Number of pins: 2
• Corresponds to the original part in colour: black
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PT009107471

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Construction Year to: 09.1995
• Manufacturer: FAE

• Sensor Type: NTC Sensor
• Thread Size: M14 x 1,5
• Spanner Size: 19
• Colour: black
• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MEY

• Engine Code: M43 B18 (184E2)
• Colour: black
• Thread Size: M14x1,5
• Spanner Size: 19
• Name: EP 1.830.176
• Manufacturer: EPS

• Engine Code: M43 B18 (184E2)
• Construction Year to: 09.1995
• Manufacturer: BOSCH
• Name: BS 0280130026

• Construction Year from: 03.1996
• Length [mm]: 80
• Number of connectors: 2
• Weight [kg]: 0.016
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year from: 09.1995
• Length [mm]: 68
• External Thread Size: M12 x 1,5
• Spanner Size: 22
• Number of connectors: 4
• Colour: black
• Screw length below head [mm]: 25
• Weight [kg]: 0.025
• Supplementary Article/Info 2: with seal ring
• Manufacturer: SWAG
• Name: SW 20 93 2915

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Construction Year from: 09.1995
• Length [mm]: 68
• External Thread Size: M12 x 1,5
• Spanner Size: 22
• Number of connectors: 4
• Colour: black
• Screw length below head [mm]: 25
• Weight [kg]: 0.025
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Construction Year from: 09.1995
• Cable Length [mm]: 910
• Number of pins: 3
• Weight [kg]: 0.11
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY

• Construction Year to: 03.1996
• Vehicle Equipment: for vehicles with headlamp cleaning system
• Length [mm]: 97.5
• Number of connectors: 2
• Weight [kg]: 0.02
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Weight [kg]: 0.02
• Warranty: 3 years warranty
• Number of pins: 2
• Manufacturer: SKV GERMANY
• Name: CE 17SKV706

• Engine Code: M43 B18 (184E2)
• Construction Year from: 09.1995
• Thread Size: M12x1,5
• Spanner Size: 22
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Construction Year to: 09.1995
• Cable Length [mm]: 900
• Number of pins: 3
• Weight [kg]: 0.1
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY

• Engine Code: M43 B18 (184E2)
• Construction Year from: 09.1995
• Sensor Type: NTC Sensor
• Thread Size: M12 x 1,5
• Spanner Size: 22
• Supplementary Article/Info 2: with seal ring
• Colour: black
• Number of pins: 4
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MEY

• Construction Year to: 03.1996
• Number of pins: 2
• Manufacturer: METZGER

• Supplementary Article/Info 2: with cable
• Length [mm]: 500
• Height [mm]: 28
• Resistor [Ohm]: 1,400
• Number of connectors: 3
• Manufacturer: VERNET

• Construction Year to: 09.1995
• Cable Length [mm]: 855
• Number of pins: 3
• Manufacturer: DELPHI
• Name: DE SS11022

• Construction Year to: 09.1995
• Connector Shape: rectangular
• Number of pins: 3
• Supplementary Article/Info 2: with cable
• Name: ANDUR, VŽNTVOLL
• Manufacturer: HAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Construction Year to: 09.1995
• Engine Code: M43B18
• Length [mm]: 630
• Width [mm]: 37
• Height [mm]: 60
• Weight [kg]: 0.09, 0.129
• Cable Length [mm]: 620
• Supplementary Article/Info 2: for camshaft
• Sensor Type: Inductive Sensor
• Number of pins: 3
• Number of connectors: 3
• Rated Voltage [V]: 12
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year from: 03.1996
• Number of pins: 2
• Alternative Repair Kit: 0901360
• Manufacturer: METZGER

• Construction Year to: 09.1995
• Number of pins: 3
• Cable Length [mm]: 872
• Fitting Depth [mm]: 24.1
• Name: ANDUR, VŽNTVOLL
• Manufacturer: TRI

• Engine Code: M43 B18 (184E2)
• Construction Year to: 09.1995
• Length [mm]: 960
• Name: ANDUR, VŽNTVOLL
• Manufacturer: EPS

• Engine Code: M43 B18 (184E2)
• Construction Year from: 10.1995
• Length [mm]: 880
• Name: ANDUR, VŽNTVOLL
• Manufacturer: EPS

• Construction Year to: 09.1995
• Engine Code: M43B18
• Sensor Type: Inductive Sensor
• Number of pins: 3
• Voltage [V]: 12
• Connector Shape: angled
• Supplementary Article/Info 2: with cable
• Resistor [Ohm]: 550
• Weight [kg]: 0.12
• Manufacturer: VALEO
• Name: VA 254135

Manufacturer: MAGNETI MARELLI

• Length [mm]: 630, 950
• Supplementary Article/Info 2: for camshaft
• Number of pins: 3
• Cable Length [mm]: 635, 890
• Sensor Type: Inductive Sensor
• Resistor [Ohm]: 540
• Number of connectors: 3
• Rated Voltage [V]: 12
• Weight [kg]: 0.122
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.