• Fitting Position: Rear Axle
• Outer Diameter [mm]: 345
• Brake Disc Thickness [mm]: 24
• Brake Disc Type: two-part brake disc, Vented
• Machining: High-carbon
• Surface: Coated
• Number of Holes: 5
• Supplementary Article/Info 2: with bolts/screws
• Bolt Hole Circle Ø [mm]: 120
• Height [mm]: 63
• Centering Diameter [mm]: 75
• Manufacturer: KAMOKA

• for OE number: 34 11 6 763 824
• Fitting Position: Front Axle
• Brake Disc Type: internally vented
• Brake Disc Thickness [mm]: 30
• Outer Diameter [mm]: 348
• Number of Holes: 5
• Bolt Hole Circle Ø [mm]: 120
• Manufacturer: TRUCKTEC AUTOMOTIVE

• Fitting Position: Rear Axle
• Outer Diameter [mm]: 345
• Brake Disc Thickness [mm]: 24
• Height [mm]: 63
• Rim Hole Number: 5
• Weight [kg]: 9.5
• Brake Disc Type: Vented
• Surface: Coated
• Installation Information: Important: Observe Fitting Instructions
• Manufacturer: A.B.S.

• Fitting Position: Front Axle
• Outer Diameter [mm]: 348
• Brake Disc Thickness [mm]: 30
• Brake Disc Type: two-part brake disc, Vented
• Machining: High-carbon
• Surface: Coated
• Number of Holes: 5
• Bolt Hole Circle Ø [mm]: 120
• Height [mm]: 77
• Centering Diameter [mm]: 79
• Supplementary Article/Info 2: with bolts/screws
• Manufacturer: KAMOKA

• Fitting Position: Rear Axle Left, Rear Axle Right
• Brake Disc Type: internally vented
• Outer Diameter [mm]: 345
• Brake Disc Thickness [mm]: 24
• Number of Holes: 5
• Bolt Hole Circle Ø [mm]: 120
• Centering Diameter [mm]: 79
• Replace in pairs only:
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Brake Disc Thickness [mm]: 24
• Rim Hole Number: 5
• Number of mounting bores: 1
• Thickness [mm]: 63.1
• Outer Diameter [mm]: 345
• Bolt Hole Circle Ø [mm]: 120
• Machining: High-carbon
• Surface: Coated
• Brake Disc Type: internally vented
• Fitting Position: Rear Axle
• Minimum thickness [mm]: 22.4
• Centering Diameter [mm]: 75
• Weight [kg]: 9.66
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Rear Axle
• Brake Disc Type: Externally Vented
• Machining: High-carbon
• Surface: Coated
• Outer Diameter [mm]: 345
• Brake Disc Thickness [mm]: 24
• Height [mm]: 63
• Rim Hole Number: 5
• Bolt Hole Circle Ø [mm]: 120
• Centering Diameter [mm]: 75
• Test Mark: KBA 60787
• Minimum thickness [mm]: 22.4
• Weight [kg]: 9.4
• Hole Arrangement/Number: 6/5
• Manufacturer: ZIMMERMANN

• Country Specific Design: USA
• Outer Diameter [mm]: 340
• Height [mm]: 73.2
• Brake Disc Type: perforated/vented
• Brake Disc Thickness [mm]: 30
• Minimum thickness [mm]: 28.4
• Number of Holes: 5
• Surface: Painted
• Fitting Position: Front Axle
• Manufacturer: JAPKO

• Brake Disc Thickness [mm]: 24
• Rim Hole Number: 5
• Number of mounting bores: 1
• Thickness [mm]: 63
• Outer Diameter [mm]: 345
• Bolt Hole Circle Ø [mm]: 120
• Machining: High-carbon
• Surface: Coated
• Brake Disc Type: internally vented
• Fitting Position: Rear Axle
• Minimum thickness [mm]: 22.4
• Centering Diameter [mm]: 75
• Weight [kg]: 9.66
• Name: Piduriketas
• Manufacturer: BLP

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Front Axle
• not for country specific design: USA
• Brake Disc Thickness [mm]: 36
• Height [mm]: 77
• Centering Diameter [mm]: 79
• Brake Disc Type: internally vented
• Outer Diameter [mm]: 348
• Number of Holes: 5
• Multi-piece: one-piece
• Minimum thickness [mm]: 34.4
• Manufacturer: LPR

• Construction Year to: 07.2010
• Fitting Position: Rear Axle
• Outer Diameter [mm]: 345
• Brake Disc Thickness [mm]: 24
• Minimum thickness [mm]: 22.4
• Height [mm]: 63.1
• Bolt Hole Circle Ø [mm]: 120
• Brake Disc Type: Vented
• Centering Diameter [mm]: 75
• Number of Holes: 5
• Surface: Coated
• Machining: High-carbon
• Supplementary Article/Info 2: with bolts/screws
• Fulfils ECE norm: ECE-R90
• Drill Diameter, up to [mm]: 14.8
• Name: PIDURIKETAS
• Manufacturer: BOS

• Brake Disc Thickness [mm]: 36
• Rim Hole Number: 5
• Number of mounting bores: 1
• Thickness [mm]: 77.2
• Outer Diameter [mm]: 348
• Bolt Hole Circle Ø [mm]: 120
• Machining: High-carbon
• Surface: Coated
• Brake Disc Type: internally vented
• Fitting Position: Front Axle
• Minimum thickness [mm]: 34.4
• Centering Diameter [mm]: 79
• Weight [kg]: 13.25
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Front Axle
• Brake Disc Type: internally vented
• Machining: High-carbon
• Surface: Coated
• Outer Diameter [mm]: 348
• Brake Disc Thickness [mm]: 30
• Height [mm]: 77
• Rim Hole Number: 5
• Bolt Hole Circle Ø [mm]: 120
• Centering Diameter [mm]: 79
• Test Mark: ECE R90 APPROVED
• Minimum thickness [mm]: 28.4
• Weight [kg]: 10.1
• Hole Arrangement/Number: 6/5
• Manufacturer: ZIMMERMANN

• Fitting Position: Front Axle
• Brake Disc Type: Vented
• Number of Holes: 5
• Test Mark: E1 90R-02C0074/1938
• Supplementary Article/Info 2: without wheel bearing, without ABS sensor ring
• Surface: Coated
• Machining: High-carbon
• Outer Diameter [mm]: 348
• Brake Disc Thickness [mm]: 36
• Minimum thickness [mm]: 34.4
• Centering Diameter [mm]: 79
• Height [mm]: 77.1
• Manufacturer: DELPHI LOCKHEED HAMULCE
• Name: DE BG9321C
• Quality class: PJ

• Country Specific Design: Germany
• Fitting Position: Front Axle
• Brake Disc Type: Vented
• Brake Disc Thickness [mm]: 30
• Outer Diameter [mm]: 348
• Height [mm]: 77.2
• Centering Diameter [mm]: 79
• Bolt Hole Circle Ø [mm]: 120
• Rim Hole Number: 5
• Name: Piduriketas
• Manufacturer: QUARO

• Brake Disc Thickness [mm]: 24
• Rim Hole Number: 5
• Number of mounting bores: 1
• Thickness [mm]: 63.1
• Outer Diameter [mm]: 345
• Bolt Hole Circle Ø [mm]: 120
• Machining: High-carbon
• Surface: Coated
• Brake Disc Type: internally vented
• Fitting Position: Rear Axle
• Minimum thickness [mm]: 22.4
• Centering Diameter [mm]: 75
• Weight [kg]: 9.66
• Name: SW 20 10 4807
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Front Axle
• not for country specific design: Germany
• Outer Diameter [mm]: 348
• Brake Disc Thickness [mm]: 36
• Height [mm]: 77.2
• Rim Hole Number: 5
• Weight [kg]: 13.63
• Brake Disc Type: Vented
• Installation Information: Important: Observe Fitting Instructions
• Manufacturer: A.B.S.

• Brake Disc Thickness [mm]: 30
• Rim Hole Number: 5
• Number of mounting bores: 1
• Thickness [mm]: 77.2
• Outer Diameter [mm]: 348
• Bolt Hole Circle Ø [mm]: 120
• Machining: High-carbon
• Surface: Coated
• Brake Disc Type: internally vented
• Fitting Position: Front Axle
• Minimum thickness [mm]: 28.4
• Centering Diameter [mm]: 79
• Weight [kg]: 11.46
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Rear Axle
• Outer Diameter [mm]: 345
• Height [mm]: 63.1
• Brake Disc Thickness [mm]: 24
• Minimum thickness [mm]: 22.4
• Centering Diameter [mm]: 75
• Bolt Hole Circle Ø [mm]: 120
• Wheel Bolt Bore Ø [mm]: 14.5
• Number of Holes: 5
• Brake Disc Type: Vented
• Surface: Zink flake coated
• Machining: High-carbon
• Supplementary Article/Info 2: with bolts/screws
• Required quantity: 2
• Name: Piduriketas
• Manufacturer: MEY

General Information: High-carbon MEYLE-PD brake disc. Increased carbon content of brake disc material to 3.6-3.9% due to a special high carbonization process. The result: Better warping resistance because of increased thermal conductivity.

• Brake Disc Hub Height [mm]: 39.2
• Fitting Position: Rear Axle
• Rim Hole Number: 5
• Height [mm]: 63.2
• Brake Disc Type: Vented
• Brake Disc Thickness [mm]: 24
• Minimum thickness [mm]: 22.4
• Outer Diameter [mm]: 345
• Centering Diameter [mm]: 75
• Bolt Hole Circle Ø [mm]: 120
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Rear Axle
• Brake Disc Type: Vented
• Number of Holes: 5
• Test Mark: E1 90R-02C0506/1586
• Supplementary Article/Info 2: without wheel bearing, without ABS sensor ring
• Surface: Coated
• Machining: High-carbon
• Outer Diameter [mm]: 345
• Brake Disc Thickness [mm]: 24
• Minimum thickness [mm]: 22.4
• Centering Diameter [mm]: 75
• Height [mm]: 63.1
• Manufacturer: DELPHI LOCKHEED HAMULCE
• Name: DE BG4753C

• Country Specific Design: Germany
• Fitting Position: Front Axle
• Outer Diameter [mm]: 348
• Height [mm]: 77.2
• Brake Disc Thickness [mm]: 30
• Minimum thickness [mm]: 28.4
• Centering Diameter [mm]: 79
• Bolt Hole Circle Ø [mm]: 120
• Wheel Bolt Bore Ø [mm]: 14.5
• Number of Holes: 5
• Brake Disc Type: Vented
• Surface: Zink flake coated
• Machining: High-carbon
• Supplementary Article/Info 2: with bolts/screws
• Required quantity: 2
• Name: Piduriketas
• Manufacturer: MEY

General Information: High-carbon MEYLE-PD brake disc. Increased carbon content of brake disc material to 3.6-3.9% due to a special high carbonization process. The result: Better warping resistance because of increased thermal conductivity.

• Fitting Position: Rear Axle
• Brake Disc Type: Externally Vented, Perforated
• Machining: High-carbon
• Surface: Coated
• Outer Diameter [mm]: 345
• Brake Disc Thickness [mm]: 24
• Height [mm]: 63
• Rim Hole Number: 5
• Bolt Hole Circle Ø [mm]: 120
• Centering Diameter [mm]: 75
• Test Mark: ECE R90 APPROVED
• Minimum thickness [mm]: 22.4
• Weight [kg]: 9.4
• Hole Arrangement/Number: 6/5
• Manufacturer: ZIMMERMANN

• Fitting Position: Front Axle
• Brake Disc Type: internally vented
• Machining: High-carbon
• Surface: Coated
• Outer Diameter [mm]: 348
• Brake Disc Thickness [mm]: 36
• Height [mm]: 77
• Rim Hole Number: 5
• Bolt Hole Circle Ø [mm]: 120
• Centering Diameter [mm]: 79
• Test Mark: ECE R90 APPROVED
• Minimum thickness [mm]: 34.4
• Weight [kg]: 13.4
• Hole Arrangement/Number: 6/5
• Manufacturer: ZIMMERMANN

• Fitting Position: Front Axle
• Brake Disc Type: internally vented, Perforated
• Machining: High-carbon
• Surface: Coated
• Outer Diameter [mm]: 348
• Brake Disc Thickness [mm]: 30
• Height [mm]: 77
• Rim Hole Number: 5
• Bolt Hole Circle Ø [mm]: 120
• Centering Diameter [mm]: 79
• Test Mark: ECE R90 APPROVED
• Minimum thickness [mm]: 28.4
• Weight [kg]: 10.1
• Hole Arrangement/Number: 6/5
• Manufacturer: ZIMMERMANN

• Fitting Position: Front Axle
• Alternatively:
• Height [mm]: 77
• Weight [kg]: 13.5
• Brake Disc Type: Vented
• Brake Disc Thickness [mm]: 36
• Minimum thickness [mm]: 34.4
• Outer Diameter [mm]: 348
• Number of Holes: 5
• Centering Diameter [mm]: 79
• Tightening Torque [Nm]: 100
• Surface: Coated
• Packing Type: Box
• Quantity Unit: Piece
• Supplementary Article/Info 2: with bolts/screws
• Version: JC
• Packaging length [cm]: 33
• Packaging width [cm]: 33
• Packaging height [cm]: 9.5
• Manufacturer: JURID

• Outer Diameter [mm]: 348
• Brake Disc Thickness [mm]: 36
• Brake Disc Type: two-part brake disc, Vented
• Fitting Position: Front Axle
• Minimum thickness [mm]: 34.4
• Machining: High-carbon
• Surface: Painted
• Number of Holes: 5
• Bolt Hole Circle Ø [mm]: 120
• Height [mm]: 77
• Centering Diameter [mm]: 79
• Name: Piduriketas
• Manufacturer: QUARO

• Fitting Position: Rear Axle Left
• Brake Disc Type: Externally Vented, slotted
• Machining: High-carbon
• Surface: Coated
• Outer Diameter [mm]: 345
• Brake Disc Thickness [mm]: 24
• Height [mm]: 63
• Rim Hole Number: 5
• Bolt Hole Circle Ø [mm]: 120
• Centering Diameter [mm]: 75
• paired article number: 150.3461.55
• directional:
• Test Mark: ohne ABE
• Minimum thickness [mm]: 22.4
• Weight [kg]: 9.4
• Hole Arrangement/Number: 6/5
• Manufacturer: ZIMMERMANN

• Fitting Position: Rear Axle Right
• Brake Disc Type: Externally Vented, slotted
• Machining: High-carbon
• Surface: Coated
• Outer Diameter [mm]: 345
• Brake Disc Thickness [mm]: 24
• Height [mm]: 63
• Rim Hole Number: 5
• Bolt Hole Circle Ø [mm]: 120
• Centering Diameter [mm]: 75
• paired article number: 150.3461.54
• directional:
• Test Mark: ohne ABE
• Minimum thickness [mm]: 22.4
• Weight [kg]: 9.4
• Hole Arrangement/Number: 6/5
• Manufacturer: ZIMMERMANN

• Fitting Position: Rear Axle
• Outer Diameter [mm]: 345
• Brake Disc Thickness [mm]: 24
• Height [mm]: 63
• Rim Hole Number: 5
• Weight [kg]: 8.49
• Brake Disc Type: Vented, two-part brake disc
• Surface: Coated
• Material: Aluminium
• Technical Information: Two-piece brake disc with aluminium hub.
• Manufacturer: A.B.S.

• Fitting Position: Rear Axle
• Outer Diameter [mm]: 345
• Brake Disc Thickness [mm]: 24
• Minimum thickness [mm]: 22.4
• Brake Disc Type: two-part brake disc, Vented
• Machining: High-carbon
• Surface: Coated
• Number of Holes: 5
• Supplementary Article/Info 2: with bolts/screws
• MAPP code available:
• Bolt Hole Circle Ø [mm]: 120
• Height [mm]: 63.2
• Centering Diameter [mm]: 75
• Inner Diameter [mm]: 185
• Bore Ø [mm]: 14.5
• Test Mark: E1 90R-02C0504/1020
• Name: Piduriketas
• Manufacturer: ATE

• Fitting Position: Front Axle
• Brake Disc Type: internally vented, Perforated
• Machining: High-carbon
• Surface: Coated
• Outer Diameter [mm]: 348
• Brake Disc Thickness [mm]: 36
• Height [mm]: 77
• Rim Hole Number: 5
• Bolt Hole Circle Ø [mm]: 120
• Centering Diameter [mm]: 79
• Test Mark: ECE R90 APPROVED
• Minimum thickness [mm]: 34.4
• Weight [kg]: 13.4
• Hole Arrangement/Number: 6/5
• Manufacturer: ZIMMERMANN

• Fitting Position: Rear Axle
• Brake Disc Type: internally vented, two-part brake disc
• Brake Disc Thickness [mm]: 24
• Number of Holes: 5
• Supplementary Article/Info 2: with bolts/screws
• Height [mm]: 63
• Centering Diameter [mm]: 75
• Outer Diameter [mm]: 345
• Machining: High-carbon
• Surface: Coated
• Minimum thickness [mm]: 22.4
• Manufacturer: BREMBO
• Name: BR 09.C418.13

• Fitting Position: Rear Axle
• Brake Disc Type: Externally Vented, two-part brake disc
• Outer Diameter [mm]: 345
• Brake Disc Thickness [mm]: 24
• Height [mm]: 63.2
• Minimum thickness [mm]: 22.4
• Machining: High-carbon
• Surface: Coated
• Inner Diameter [mm]: 185
• Bolt Hole Circle Ø [mm]: 120
• Centering Diameter [mm]: 75
• Hole Arrangement/Number: 05/06
• Wheel Bolt Bore Ø [mm]: 14.5
• Number of bolts/screws: 2
• Packaging length [cm]: 37.8
• Packaging width [cm]: 37.8
• Packaging height [cm]: 15.5
• Weight [kg]: 8.6
• Name: PIDURIKETAS
• Manufacturer: TEX

Supplementary Article/Info 2: without wheel hub, without wheel bearing, without wheel studs, with bolts/screws

• Fitting Position: Front Axle
• Country Specific Design: USA
• Brake Disc Type: two-part brake disc, internally vented
• Outer Diameter [mm]: 348
• Brake Disc Thickness [mm]: 30
• Height [mm]: 77.1
• Minimum thickness [mm]: 28.4
• Machining: High-carbon
• Surface: Coated
• Inner Diameter [mm]: 186.8
• Bolt Hole Circle Ø [mm]: 120
• Centering Diameter [mm]: 79
• Hole Arrangement/Number: 05/06
• Wheel Bolt Bore Ø [mm]: 14.5
• Number of bolts/screws: 1
• Packaging length [cm]: 35.8
• Packaging width [cm]: 35.8
• Packaging height [cm]: 10.5
• Weight [kg]: 10.9
• Name: PIDURIKETAS
• Manufacturer: TEX

Supplementary Article/Info 2: without wheel hub, without wheel bearing, without wheel studs, with bolts/screws

• Construction Year to: 07.2010
• Fitting Position: Front Axle
• Outer Diameter [mm]: 348
• Brake Disc Thickness [mm]: 30
• Minimum thickness [mm]: 28.4
• Height [mm]: 77.1
• Bolt Hole Circle Ø [mm]: 120
• Brake Disc Type: two-part brake disc, Vented
• Centering Diameter [mm]: 79
• Number of Holes: 5
• Surface: Coated
• Machining: High-carbon
• Supplementary Article/Info 2: with bolts/screws
• Fulfils ECE norm: ECE-R90
• Drill Diameter, up to [mm]: 14.5
• Observe service information:
• Manufacturer: BOSCH

• Fitting Position: Front Axle
• Country Specific Design: Germany
• Brake Disc Type: Vented, two-part brake disc
• Number of Holes: 5
• Outer Diameter [mm]: 348
• Centering Diameter [mm]: 79
• Height [mm]: 77.1
• Brake Disc Thickness [mm]: 30
• Minimum thickness [mm]: 28.4
• Bolt Hole Circle Ø [mm]: 120
• Bore Ø 1 [mm]: 14.5
• Bore Ø 2 [mm]: 12.7
• Machining: High-carbon
• Manufacturer: TRW

SVHC: No information available, please contact the manufacturer!

• Fitting Position: Front Axle
• Brake Disc Type: internally vented, two-part brake disc
• Quality: Alu-Topf genietet, Alu hub riveted
• Machining: High-carbon
• Surface: Coated
• Outer Diameter [mm]: 348
• Brake Disc Thickness [mm]: 30
• Height [mm]: 77
• Rim Hole Number: 5
• Bolt Hole Circle Ø [mm]: 120
• Centering Diameter [mm]: 79
• Test Mark: ECE R90 APPROVED
• Minimum thickness [mm]: 28.4
• Weight [kg]: 10
• Hole Arrangement/Number: 6/5
• Manufacturer: ZIMMERMANN

• Fitting Position: Front Axle
• not for country specific design: Germany
• Bolt Hole Circle Ø [mm]: 120
• Thread Size: 14,5
• Brake Disc Type: Vented, two-part brake disc
• Outer Diameter [mm]: 348
• Brake Disc Thickness [mm]: 36
• Minimum thickness [mm]: 34.4
• Number of Holes: 5
• Height [mm]: 77
• Centering Diameter [mm]: 79
• Machining: High-carbon
• Name: PIDURIKETAS
• Manufacturer: TRW

SVHC: No information available, please contact the manufacturer!

• Fitting Position: Rear Axle
• Brake Disc Type: Externally Vented, two-part brake disc
• Quality: Alu-Topf genietet, Alu hub riveted
• Machining: High-carbon
• Surface: Coated
• Outer Diameter [mm]: 345
• Brake Disc Thickness [mm]: 24
• Height [mm]: 63
• Rim Hole Number: 5
• Bolt Hole Circle Ø [mm]: 120
• Centering Diameter [mm]: 75
• Test Mark: ECE R90 APPROVED
• Minimum thickness [mm]: 22.4
• Weight [kg]: 8.6
• Hole Arrangement/Number: 6/5
• Manufacturer: ZIMMERMANN

• Construction Year to: 07.2010
• Fitting Position: Front Axle
• Outer Diameter [mm]: 348
• Brake Disc Thickness [mm]: 36
• Minimum thickness [mm]: 34.4
• Height [mm]: 77
• Bolt Hole Circle Ø [mm]: 120
• Brake Disc Type: two-part brake disc, Vented
• Centering Diameter [mm]: 79
• Number of Holes: 5
• Surface: Coated
• Machining: High-carbon
• Supplementary Article/Info 2: with bolts/screws
• Fulfils ECE norm: ECE-R90
• Drill Diameter, up to [mm]: 14.5
• Observe service information:
• Name: PIDURIKETAS
• Manufacturer: BOS

• Fitting Position: Front Axle
• Brake Disc Type: internally vented, two-part brake disc
• Quality: Alu-Topf genietet, Alu hub riveted
• Machining: High-carbon
• Surface: Coated
• Outer Diameter [mm]: 348
• Brake Disc Thickness [mm]: 36
• Height [mm]: 77
• Rim Hole Number: 5
• Bolt Hole Circle Ø [mm]: 120
• Centering Diameter [mm]: 79
• Test Mark: ECE R90 APPROVED
• Minimum thickness [mm]: 34.4
• Weight [kg]: 12.6
• Hole Arrangement/Number: 6/5
• Manufacturer: ZIMMERMANN

• Fitting Position: Front Axle
• Outer Diameter [mm]: 348
• Brake Disc Thickness [mm]: 36
• Minimum thickness [mm]: 34.4
• Brake Disc Type: two-part brake disc, Vented
• Machining: High-carbon
• Surface: Coated
• Number of Holes: 5
• Supplementary Article/Info 2: with bolts/screws
• Bolt Hole Circle Ø [mm]: 120
• Height [mm]: 77
• Centering Diameter [mm]: 79
• Inner Diameter [mm]: 154.3
• Bore Ø [mm]: 14.5
• MAPP code available:
• Test Mark: E1 90R-02C0391/0990
• Name: Piduriketas
• Manufacturer: ATE
• Quality class: Q

• Fitting Position: Front Axle Left
• Brake Disc Type: internally vented, slotted
• Machining: High-carbon
• Surface: Coated
• Outer Diameter [mm]: 348
• Brake Disc Thickness [mm]: 30
• Height [mm]: 77
• Rim Hole Number: 5
• Bolt Hole Circle Ø [mm]: 120
• Centering Diameter [mm]: 79
• paired article number: 150.3434.55
• directional:
• Test Mark: ohne ABE
• Minimum thickness [mm]: 28.4
• Weight [kg]: 10.1
• Hole Arrangement/Number: 6/5
• Manufacturer: ZIMMERMANN

• Fitting Position: Front Axle Right
• Brake Disc Type: internally vented, slotted
• Machining: High-carbon
• Surface: Coated
• Outer Diameter [mm]: 348
• Brake Disc Thickness [mm]: 30
• Height [mm]: 77
• Rim Hole Number: 5
• Bolt Hole Circle Ø [mm]: 120
• Centering Diameter [mm]: 79
• paired article number: 150.3434.54
• directional:
• Test Mark: ohne ABE
• Minimum thickness [mm]: 28.4
• Weight [kg]: 10.1
• Hole Arrangement/Number: 6/5
• Manufacturer: ZIMMERMANN

• Fitting Position: Front Axle
• not for country specific design: USA
• Brake Disc Type: two-part brake disc, internally vented
• Outer Diameter [mm]: 348
• Brake Disc Thickness [mm]: 36
• Height [mm]: 77
• Minimum thickness [mm]: 34.4
• Machining: High-carbon
• Surface: Coated
• Inner Diameter [mm]: 153.7
• Bolt Hole Circle Ø [mm]: 120
• Centering Diameter [mm]: 79
• Hole Arrangement/Number: 05/06
• Wheel Bolt Bore Ø [mm]: 14.5
• Number of bolts/screws: 1
• Packaging length [cm]: 35.8
• Packaging width [cm]: 35.8
• Packaging height [cm]: 10.5
• Weight [kg]: 12.6
• Name: PIDURIKETAS
• Manufacturer: TEX

Supplementary Article/Info 2: without wheel hub, without wheel bearing, without wheel studs, with bolts/screws

• Construction Year to: 07.2010
• Fitting Position: Rear Axle
• Outer Diameter [mm]: 345
• Brake Disc Thickness [mm]: 24
• Minimum thickness [mm]: 22.4
• Height [mm]: 63.2
• Bolt Hole Circle Ø [mm]: 120
• Brake Disc Type: two-part brake disc, Vented
• Centering Diameter [mm]: 75
• Number of Holes: 5
• Surface: Coated
• Machining: High-carbon
• Supplementary Article/Info 2: with bolts/screws
• Fulfils ECE norm: ECE-R90
• Drill Diameter, up to [mm]: 14.5
• Observe service information:
• Manufacturer: BOSCH

• Fitting Position: Front Axle
• not for country specific design: USA
• Brake Disc Type: two-part brake disc, internally vented
• Outer Diameter [mm]: 348
• Brake Disc Thickness [mm]: 36
• Height [mm]: 77
• Minimum thickness [mm]: 34.4
• Machining: High-carbon
• Surface: Coated
• Inner Diameter [mm]: 153.7
• Bolt Hole Circle Ø [mm]: 120
• Centering Diameter [mm]: 79
• Hole Arrangement/Number: 05/06
• Wheel Bolt Bore Ø [mm]: 14.5
• Number of bolts/screws: 1
• Weight [kg]: 12.6
• Name: HE 8DD355120791
• Manufacturer: HELLA PAGID

Supplementary Article/Info 2: without wheel hub, without wheel bearing, without wheel studs, with bolts/screws

• Fitting Position: Front Axle
• Vehicle Equipment: for vehicles without sports package
• Brake Disc Type: internally vented, two-part brake disc
• Brake Disc Thickness [mm]: 36
• Number of Holes: 5
• Supplementary Article/Info 2: with bolts/screws
• Height [mm]: 77
• Centering Diameter [mm]: 79
• Outer Diameter [mm]: 348
• Machining: High-carbon
• Surface: Coated
• Minimum thickness [mm]: 34.4
• Manufacturer: BREMBO
• Name: BR 09.C393.13

• Fitting Position: Rear Axle
• Brake Disc Type: Externally Vented, two-part brake disc
• Outer Diameter [mm]: 345
• Brake Disc Thickness [mm]: 24
• Height [mm]: 63.2
• Minimum thickness [mm]: 22.4
• Machining: High-carbon
• Surface: Coated
• Inner Diameter [mm]: 185
• Bolt Hole Circle Ø [mm]: 120
• Centering Diameter [mm]: 75
• Hole Arrangement/Number: 05/06
• Wheel Bolt Bore Ø [mm]: 14.5
• Number of bolts/screws: 2
• Weight [kg]: 8.6
• Name: HE 8DD355123231
• Manufacturer: HELLA PAGID

Supplementary Article/Info 2: without wheel hub, without wheel bearing, without wheel studs, with bolts/screws

• Fitting Position: Rear Axle
• Brake Disc Type: Vented, two-part brake disc
• Number of Holes: 5
• Outer Diameter [mm]: 345
• Centering Diameter [mm]: 75
• Height [mm]: 63.2
• Brake Disc Thickness [mm]: 24
• Minimum thickness [mm]: 22.4
• Bolt Hole Circle Ø [mm]: 120
• Bore Ø 1 [mm]: 14.5
• Bore Ø 2 [mm]: 12.7
• Machining: High-carbon
• Name: PIDURIKETAS
• Manufacturer: TRW

SVHC: No information available, please contact the manufacturer!

• Fitting Position: Front Axle
• Brake Disc Type: two-part brake disc, internally vented
• Brake Disc Thickness [mm]: 30
• Number of Holes: 5
• Supplementary Article/Info 2: with bolts/screws
• Height [mm]: 77
• Centering Diameter [mm]: 79
• Outer Diameter [mm]: 348
• Machining: High-carbon
• Surface: Coated
• Minimum thickness [mm]: 28.4
• Name: BR 09.C419.13
• Manufacturer: BREMBO