• Fitting Position: Front Axle
• Outer Diameter 2 [mm]: 72, 39
• Height [mm]: 37
• Lisainfo: DAEWOO LANOS
• Additional information: DAEWOO LANOS

• Installatsiooni pool: Tagasild, Tagasild vasakul, Tagasild paremal
• Seerianumber: KLT-DW-020
• Manufacturer: NTY

• Fitting Position: Rear Axle
• Braking/Drive Dynamics: for vehicles without ABS
• Width [mm]: 14.6
• Inner Diameter [mm]: 17.5
• Outer Diameter [mm]: 39.9
• Width 1 [mm]: 13.8
• Width 2 [mm]: 14.2
• Outer Diameter 1 [mm]: 50.3
• Inner Diameter 1 [mm]: 29
• Name: RATTALAAGRIKOMPLEKT
• Manufacturer: OPT

• Fitting Position: Rear Axle
• new version:
• Bearing Type: Tapered Roller Bearing
• Outer Diameter 1 [mm]: 40
• Outer Diameter 2 [mm]: 50
• Width 1 [mm]: 14.6
• Width 2 [mm]: 15
• Inner Diameter 1 [mm]: 17.5
• Weight [kg]: 0.2
• Inner Diameter 2 [mm]: 29
• Supplementary Article/Info 2: with shaft seal
• Name: RATTALAAGRIKOMPLEKT
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Piirangutega toode/piirangu info 2: koos rõngastihendiga
• Installatsiooni pool: Tagasild
• Välisläbimõõt 1 [mm]: 50
• Siseläbimõõt 1 [mm]: 29
• Välisläbimõõt 2 [mm]: 40
• Siseläbimõõt 2 (mm): 17
• Manufacturer: AIC

Üldine informatsioon: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Fitting Position: Rear Axle
• new version:
• Bearing Type: Tapered Roller Bearing
• Outer Diameter 1 [mm]: 40
• Outer Diameter 2 [mm]: 50
• Width 1 [mm]: 14.6
• Width 2 [mm]: 15
• Inner Diameter 1 [mm]: 17.5
• Weight [kg]: 0.2
• Inner Diameter 2 [mm]: 29
• Supplementary Article/Info 2: with shaft seal
• Name: SW 40 85 0002
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Rear Axle
• Siseläbimõõt [mm]: 29
• Välisläbimõõt [mm]: 50,3
• Laius (mm): 15
• Siseläbimõõt 1 [mm]: 17,3
• Välisläbimõõt 1 [mm]: 40
• Laius 1 (mm): 14,6
• Manufacturer: ASHIKA

• Fitting Position: Rear Axle
• old version:
• Bearing Type: Tapered Roller Bearing
• Outer Diameter 1 [mm]: 40
• Outer Diameter 2 [mm]: 50
• Width 1 [mm]: 14
• Width 2 [mm]: 14
• Inner Diameter 1 [mm]: 17.5
• Weight [kg]: 0.274
• Inner Diameter 2 [mm]: 29
• Supplementary Article/Supplementary Info: with fastening/mounting material
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: outer, Front Axle Left, Front Axle Right
• Width [mm]: 37
• Inner Diameter [mm]: 34
• Outer Diameter [mm]: 64
• Name: RATTALAAGRIKOMPLEKT
• Manufacturer: MAX

• Fitting Position: Rear Axle
• Width [mm]: 14
• Inner Diameter [mm]: 17, 29
• Outer Diameter [mm]: 40, 50
• Bearing Type: Tapered Roller Bearing
• Weight [kg]: 0.43
• Supplementary Article/Supplementary Info: with fastening/mounting material
• Manufacturer: BLUE PRINT ZAWIESZENIE

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Front Axle, outer
• Width [mm]: 37
• Inner Diameter [mm]: 34
• Outer Diameter [mm]: 64
• Net weight [kg]: 0.51
• Name: RATTALAAGRIKOMPLEKT
• Manufacturer: NK
• Lisainfo: .
• Additional information: .

• Installatsiooni pool: esisild vasakul, esisild paremal, Esisild
• tootekoodile: KLP-DW-020P, KLP-DW-020P2
• Seerianumber: KLP-DW-020
• Manufacturer: NTY

• Fitting Position: Rear Axle
• Braking/Drive Dynamics: for vehicles without ABS
• Supplementary Article/Supplementary Info: Photo corresponds to scope of supply
• Inner Diameter 1 [mm]: 17.5
• Outer Diameter 1 [mm]: 39.9
• Width 1 [mm]: 14.6
• Inner Diameter 2 [mm]: 29
• Outer Diameter 2 [mm]: 50.3
• Width 2 [mm]: 14.7
• SVHC: No SVHC present!
• Name: RATTALAAGRIKOMPLEKT
• Manufacturer: FAG

• Installatsiooni pool: Esisild, esisild vasakul, esisild paremal
• Laius (mm): 37
• Siseläbimõõt [mm]: 34
• Välisläbimõõt [mm]: 64
• Seerianumber: KLP-DW-010
• Manufacturer: NTY
• Name: NTY KLP-DW-010

• Installatsiooni pool: esisild mõlemapoolselt
• Laius (mm): 37
• Siseläbimõõt [mm]: 40
• Välisläbimõõt [mm]: 72
• Manufacturer: JPN

• Fitting Position: Front Axle
• Width [mm]: 37
• Inner Diameter [mm]: 39
• Outer Diameter [mm]: 72
• Net weight [kg]: 0.64
• Name: RATTALAAGRIKOMPLEKT
• Manufacturer: NK

• Fitting Position: Front Axle Left, Front Axle Right
• Width 1 [mm]: 37
• Outer Diameter 1 [mm]: 72
• Inner Diameter 1 [mm]: 39
• Manufacturer: GSP

• Fitting Position: Front Axle
• Width [mm]: 37
• Inner Diameter [mm]: 39
• Outer Diameter 1 [mm]: 72
• Manufacturer: METELLI LOZYSKA KOLA PIASTY

• Fitting Position: Front Axle Left, Front Axle Right
• Version: One
• Width 1 [mm]: 37
• Outer Diameter 1 [mm]: 64
• Inner Diameter 1 [mm]: 34
• Manufacturer: GSP

• Fitting Position: Front Axle Left, Front Axle Right
• Version: Two
• Width 1 [mm]: 37
• Outer Diameter 1 [mm]: 64
• Inner Diameter 1 [mm]: 34
• Manufacturer: GSP

• Siseläbimõõt [mm]: 39
• Välisläbimõõt [mm]: 72
• Laius (mm): 37
• Installatsiooni pool: Esisild
• Manufacturer: ASHIKA

• Fitting Position: Front Axle, outer
• Width [mm]: 37
• Inner Diameter [mm]: 39
• Outer Diameter [mm]: 72
• Net weight [kg]: 0.64
• Name: RATTALAAGRIKOMPLEKT
• Manufacturer: NK

• Fitting Position: Front Axle
• Inner Diameter [mm]: 39
• Outer Diameter [mm]: 72
• Width [mm]: 37
• Weight [kg]: 0.662
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Front Axle
• Width [mm]: 37
• Inner Diameter [mm]: 34
• Outer Diameter [mm]: 64
• Manufacturer: OPTIMAL

• Fitting Position: Front Axle
• Width [mm]: 37
• Inner Diameter [mm]: 39
• Outer Diameter [mm]: 72
• Supplementary Article/Info 2: without nut
• Manufacturer: OPTIMAL

• Width [mm]: 39
• Inner Diameter [mm]: 39
• Outer Diameter [mm]: 74
• Bearing Type: Angular Ball Bearing
• Fitting Position: Front Axle Left, Front Axle Right
• Weight [kg]: 0.768
• Supplementary Article/Supplementary Info: with axle nut
• Supplementary Article/Info 2: with retaining ring
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Width [mm]: 39
• Inner Diameter [mm]: 39
• Outer Diameter [mm]: 74
• Bearing Type: Angular Ball Bearing
• Fitting Position: Front Axle Left, Front Axle Right
• Weight [kg]: 0.87
• Supplementary Article/Info 2: with retaining ring
• Supplementary Article/Supplementary Info: with axle nut
• Manufacturer: BLUE PRINT ZAWIESZENIE

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Installatsiooni pool: Esisild
• Laius (mm): 37
• Siseläbimõõt [mm]: 34
• Välisläbimõõt [mm]: 64
• Manufacturer: KAVO

• Fitting Position: Left, Rear Axle
• Rotation angle [°]: 90
• Tightening Torque [Nm]: 20, 130
• Manufacturer: SNR
• Name: SN R153.14

• Siseläbimõõt [mm]: 34
• Välisläbimõõt [mm]: 66
• Laius (mm): 37
• Installatsiooni pool: esisild vasakul, esisild paremal
• Manufacturer: AIC

Üldine informatsioon: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Fitting Position: Front Axle Left, Front Axle Right
• Vehicle configuration line / variant: REAR LR+FR
• for OE number: 94535254
• Inner Diameter [mm]: 39
• Width 1 [mm]: 37
• Number of mounting bores: 1
• Name: DA KWD1432
• Manufacturer: DAYCO

• Fitting Position: Left, Front Axle
• Manufacturer: SNR
• Name: SN R190.00

• Fitting Position: Front Axle
• Supplementary Article/Supplementary Info: Photo corresponds to scope of supply
• Inner Diameter [mm]: 34
• Outer Diameter [mm]: 64
• Width [mm]: 37
• SVHC: No SVHC present!
• Name: RATTALAAGRIKOMPLEKT
• Manufacturer: FAG

• Fitting Position: Front Axle
• Supplementary Article/Supplementary Info: Photo corresponds to scope of supply
• Inner Diameter [mm]: 39
• Outer Diameter [mm]: 72
• Width [mm]: 37
• SVHC: No SVHC present!
• Manufacturer: FAG
• Name: LU 713644670

• Fitting Position: Left, Front Axle
• Width 1 [mm]: 37
• Outer Diameter 1 [mm]: 72
• Inner Diameter 1 [mm]: 39
• Manufacturer: SNR /NTN-SNR/

• Fitting Position: Right, Left, Rear Axle, Front Axle
• Manufacturer: SNR
• Name: SN R184.55

• Installatsiooni pool: Tagasild, Tagasild vasakul, Tagasild paremal
• Seerianumber: KLT-PL-002
• Manufacturer: NTY

Piirangutega toode/piirangu info 2: koos rattakeskmega, koos integreeritud ABS-anduriga

• Fitting Position: Rear Axle
• Outer Diameter [mm]: 136
• Braking/Drive Dynamics: for vehicles with ABS
• Manufacturer: KAMOKA PRZEGUBY PÓ£OSIE PIASTY

• Fitting Position: Rear Axle
• Braking/Drive Dynamics: for vehicles with ABS
• Veljeaukude hulk: 4
• Siseläbimõõt [mm]: 56
• Välisläbimõõt [mm]: 136
• Laius 2 (mm): 78
• Välisläbimõõt 1 [mm]: 60
• Välisläbimõõt 2 [mm]: 57
• Manufacturer: JPN

• Fitting Position: Rear Axle
• Width [mm]: 148.5
• Inner Diameter [mm]: 56.5
• Outer Diameter [mm]: 136
• Supplementary Article/Info 2: with integrated ABS sensor
• Net weight [kg]: 3.4
• Name: RATTALAAGRIKOMPLEKT
• Manufacturer: NK

• Fitting Position: Rear Axle
• Rim Hole Number: 4
• Width [mm]: 148.5
• Outer Diameter [mm]: 136
• Braking/Drive Dynamics: for vehicles with ABS
• Manufacturer: OPTIMAL

• Fitting Position: Rear Axle
• Braking/Drive Dynamics: for vehicles with ABS
• Supplementary Article/Supplementary Info: Photo corresponds to scope of supply
• Outer Diameter [mm]: 136
• Outer Diameter 2 [mm]: 57
• Outer Diameter 1 [mm]: 60
• Width 2 [mm]: 78
• Rim Hole Number: 4
• Inner Diameter [mm]: 56
• SVHC: No SVHC present!
• Name: RATTALAAGRIKOMPLEKT
• Manufacturer: FAG