• Filter type: In-Line Filter
• Outer Diameter [mm]: 36
• Overall Length [mm]: 109
• Manufacturer: HENGST FILTER

• Filter type: In-Line Filter
• Height [mm]: 136
• Outer Diameter [mm]: 62
• Outer Diameter 1 [mm]: 62
• Thread Size: M12x1,5
• Manufacturer: JP GROUP
• Lisainfo: Fuel filter
• Additional information: Fuel filter

• Construction Year to: 03.1995
• Engine Code: AR67203
• Outer Diameter 1 [mm]: 63.5
• Thread Size Entry: M 14 X 1,5
• Height [mm]: 154.5
• Outer Diameter [mm]: 55.5
• Thread Size Exit: M 12 X 1,5
• Weight [kg]: 0.256
• Filter type: In-Line Filter
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Driven Units: Camshaft
• Trim Level: HSN
• Number of Teeth: 173
• Width [mm]: 18
• Manufacturer: DAYCO

• Filter type: In-Line Filter
• Diameter [mm]: 55
• Height [mm]: 134
• Thread Size Entry: M14x1,5
• Thread Size Exit: M12x1,5
• Packaging height [cm]: 14.6
• Net Weight [g]: 172
• Packaging length [cm]: 5.6
• Packaging width [cm]: 5.6
• Manufacturer: KNECHT
• Name: KN KL5

• Height [mm]: 134
• Outer Diameter [mm]: 55
• Packing Type: Box
• Filter type: In-Line Filter
• Thread Size 1: M14x1.5
• Thread Size 2: M12x1.5
• Packaging length [cm]: 6.5
• Packaging width [cm]: 6.5
• Packaging height [cm]: 15.3
• Name: CH CFF100203
• Manufacturer: CHAMPION

• Construction Year from: 11.1992
• Brake Caliper Type: Cast iron brake caliper
• Fitting Position: Rear Axle
• Thickness [mm]: 14.4
• Width [mm]: 87.4
• Height [mm]: 44.5
• Wear Warning Contact: not prepared for wear indicator
• Brake System: TRW
• Weight [kg]: 0.65
• Manufacturer: TOMEX BRAKES

• Construction Year to: 03.1995
• Filter type: Spin-on Filter
• Height [mm]: 135
• Outer Diameter [mm]: 58
• Thread Size Entry: M 14x1,5
• Thread Size Exit: M 12x1,5
• Weight [kg]: 0.18
• Manufacturer: VALEO

• Fitting Position: Rear Axle
• FMSI Code: D228-7309 D228-7498
• Test Mark: E1 90R-01878/541
• WVA Number: 21144
• Brake System: TRW
• Supplementary Article/Info 2: with anti-squeak plate
• Supplementary Article/Supplementary Info: with accessories
• Friction Lining Material: Low-Metallic
• Wear Warning Contact: not prepared for wear indicator
• Width 1 [mm]: 87.5
• Width 2 [mm]: 87
• Height 1 [mm]: 66.8
• Height 2 [mm]: 66.8
• Thickness 1 [mm]: 16
• Thickness 2 [mm]: 16
• Manufacturer: DELPHI LOCKHEED HAMULCE
• Name: DE LP451

• Filter type: Spin-on Filter
• Height [mm]: 135
• Outer Diameter [mm]: 58
• Thread Size Entry: M14x1.5
• Thread Size Exit: M 12 X 1.5
• SVHC: No SVHC present!
• Manufacturer: FILTRON

• Construction Year to: 03.1995
• Fitting Position: Rear Axle
• Brake System: TRW
• Width [mm]: 88
• Height [mm]: 44.5
• Thickness [mm]: 14.4
• WVA Number: 21103
• Wear Warning Contact: excl. wear warning contact
• Supplementary Article/Info 2: without anti-squeak plate
• Test Mark: ECE-R90
• Weight [kg]: 0.73
• Manufacturer: VALEO
• Name: VA 301142

• Fitting Position: Rear Axle
• Test Mark: E9 90R-01825/042
• WVA Number: 21103
• Brake System: TRW
• Supplementary Article/Info 2: with anti-squeak plate
• Supplementary Article/Supplementary Info: with accessories
• Friction Lining Material: Low-Metallic
• Wear Warning Contact: not prepared for wear indicator
• Width 1 [mm]: 87.6
• Width 2 [mm]: 87.5
• Height 1 [mm]: 44
• Height 2 [mm]: 44
• Thickness 1 [mm]: 14.5
• Thickness 2 [mm]: 14.5
• Name: DE LP522
• Manufacturer: DELPHI

• Braking System: for vehicles without Performance brakes
• Length [mm]: 87.1
• Width [mm]: 42.8
• Test Mark: ECE R90 Approved
• Fitting Position: Rear Axle
• Thickness 1 [mm]: 14.2
• Weight [kg]: 0.691
• Supplementary Article/Info 2: with screw set
• Manufacturer: FEBI HAMULCE

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Rear Axle
• Test Mark: R90 Homologated
• Length [mm]: 87
• Weight [kg]: 0.76
• Height 1 [mm]: 44.5
• Wear Warning Contact: not prepared for wear indicator
• Supplementary Article/Supplementary Info: with accessories
• Brake System: TRW
• Packing Type: Box
• Supplementary Article/Info 2: with brake caliper screws
• Thickness 1 [mm]: 14.3
• WVA Number: 23177
• Manufacturer: JAPKO

• Fitting Position: Rear Axle
• FMSI Code: D1478-8677
• Test Mark: E9 90R-01825/120
• WVA Number: 23177
• Brake System: TRW
• Supplementary Article/Info 2: with adhesive film
• Supplementary Article/Supplementary Info: with accessories
• Friction Lining Material: Low-Metallic
• Wear Warning Contact: not prepared for wear indicator
• Width 1 [mm]: 87.5
• Width 2 [mm]: 87.3
• Height 1 [mm]: 44
• Height 2 [mm]: 44
• Thickness 1 [mm]: 14
• Thickness 2 [mm]: 14
• Manufacturer: DELPHI LOCKHEED HAMULCE
• Name: DE LP1472

• Fitting Position: Rear Axle
• Thickness [mm]: 14.4
• Width [mm]: 87.4
• Height [mm]: 44.5
• Brake System: TRW
• Weight [kg]: 0.63
• Manufacturer: TOMEX BRAKES

• Fitting Position: Rear Axle
• Width [mm]: 87.2
• Height [mm]: 44.6
• Thickness [mm]: 14.4
• Wear Warning Contact: not prepared for wear indicator
• Supplementary Article/Info 2: with brake caliper screws
• WVA Number: 23177
• Brake System: Lucas
• Observe mounting information:
• Packaging length [cm]: 9.5
• Packaging width [cm]: 8.2
• Packaging height [cm]: 7.3
• Manufacturer: MINTEX

• Fitting Position: Rear Axle
• Width [mm]: 87
• Thickness [mm]: 14
• Height [mm]: 45
• Wear Warning Contact: excl. wear warning contact
• Supplementary Article/Supplementary Info: without accessories
• Brake System: Lucas
• Supplementary Article/Info 2: with brake caliper screws
• WVA Number: 23177
• Manufacturer: BREMBO
• Name: BR P 23 026

• Braking System: for vehicles without Performance brakes
• Length [mm]: 87.1
• Width [mm]: 42.8
• Test Mark: ECE R90 Approved
• Fitting Position: Rear Axle
• Thickness 1 [mm]: 14.2
• Weight [kg]: 0.691
• Supplementary Article/Info 2: with screw set
• Name: SW 70 91 6172
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Front Axle
• Construction Year from: 01.1995
• Drive Type: All-wheel Drive
• Test Mark: E1 90R-01881/1132
• WVA Number: 23289 21637
• Brake System: Continental
• Supplementary Article/Info 2: with anti-squeak plate
• Supplementary Article/Supplementary Info: without accessories
• Friction Lining Material: Low-Metallic
• Wear Warning Contact: incl. wear warning contact
• Width 1 [mm]: 155.1
• Width 2 [mm]: 156.3
• Height 1 [mm]: 61.7
• Height 2 [mm]: 58.9
• Thickness 1 [mm]: 18.5
• Thickness 2 [mm]: 18.5
• Manufacturer: DELPHI LOCKHEED HAMULCE
• Name: DE LP1587

• Construction Year to: 04.1996
• Fitting Position: Rear Axle
• Supplementary Article/Info 2: with bolts/screws, with mounting manual
• Material: Low-Metallic
• Test Mark: ECE-R90
• WVA Number: 21103
• Thickness [mm]: 14.4
• Width [mm]: 87.4
• Height [mm]: 44.5
• Number of bolts/screws: 4
• Number of springs: 4
• Brake System: Lucas-Girling
• Manufacturer: BOSCH UK£ADY HAMULCOWE

• Construction Year from: 01.1996
• Vehicle Equipment: for vehicles with sports package
• Length [mm]: 156.4, 155.2
• Width [mm]: 63.6, 59.1
• Test Mark: ECE R90 Approved
• Supplementary Article/Info 2: with piston clip
• Fitting Position: Front Axle
• Thickness 1 [mm]: 19.2
• Wear Warning Contact: incl. wear warning contact
• Weight [kg]: 1.82
• Manufacturer: FEBI HAMULCE

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Construction Year from: 01.1996
• Width [mm]: 15
• Number of Teeth: 130
• Belts: with trapezoidal tooth profile
• Weight [kg]: 0.065
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Construction Year from: 01.1996
• Width [mm]: 19.4
• Outer Diameter [mm]: 64
• Weight [kg]: 0.195
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Rear Axle
• Construction Year to: 03.1996
• Manufacturer Restriction: TRW
• Width [mm]: 87.4
• Height [mm]: 44.5
• Thickness [mm]: 14.4
• Wear Warning Contact: not prepared for wear indicator
• Supplementary Article/Supplementary Info: with accessories
• Supplementary Article/Info 2: with brake caliper screws
• Test Mark: E1 90R 01025/360
• Manufacturer: TRW

SVHC: No information available, please contact the manufacturer!

• Fitting Position: Rear Axle
• Brake System: LUCAS
• Width [mm]: 87
• Height [mm]: 44
• Thickness [mm]: 14
• Supplementary Article/Supplementary Info: Photo corresponds to scope of supply
• Brake Caliper Type: Aluminium Brake Caliper
• Test Mark: ECE R90 APPROVED
• Manufacturer: ZIMMERMANN

• Fitting Position: Front Axle
• Drive Type: All-wheel Drive
• Test Mark: E9 90R-02A0823/1520
• WVA Number: 21147 23168
• Brake System: TRW
• Supplementary Article/Info 2: with anti-squeak plate
• Supplementary Article/Supplementary Info: with accessories
• Friction Lining Material: Low-Metallic
• Wear Warning Contact: incl. wear warning contact
• Width 1 [mm]: 130.1
• Width 2 [mm]: 129.9
• Height 1 [mm]: 58.8
• Height 2 [mm]: 58.8
• Thickness 1 [mm]: 18.6
• Thickness 2 [mm]: 18.6
• Manufacturer: DELPHI LOCKHEED HAMULCE
• Name: DE LP875

• Construction Year from: 11.1992
• Brake Caliper Type: Aluminium Brake Caliper
• Fitting Position: Rear Axle
• Width [mm]: 87
• Height [mm]: 44.6
• Thickness [mm]: 14.2
• Wear Warning Contact: excl. wear warning contact
• Supplementary Article/Info 2: with brake caliper screws
• Number of bolts/screws: 2
• Brake System: Lucas / TRW
• Test Mark: E1 90R-01303/113
• MAPP code available:
• Manufacturer: ATE
• Quality class: Q
• Name: Brake pads

• Width [mm]: 15
• Number of Teeth: 97
• Belts: with trapezoidal tooth profile
• Weight [kg]: 0.07
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Driven Units: Balance shaft
• Trim Level: DDHSN
• Number of Teeth: 97
• Width [mm]: 15
• Manufacturer: DAYCO

• Fitting Position: Rear Axle
• Width [mm]: 87.2
• Height [mm]: 44
• Thickness [mm]: 14
• Wear Warning Contact: excl. wear warning contact
• Fulfils ECE norm: R90
• Supplementary Article/Info 2: with brake caliper screws
• Manufacturer: METZGER

• Fitting Position: Rear Axle
• Thickness [mm]: 14.7
• Test Mark: R90 Homologated
• Width [mm]: 87
• Height [mm]: 44.5
• Weight [kg]: 0.76
• Brake Caliper Type: Aluminium Brake Caliper
• Height 1 [mm]: 44.5
• Wear Warning Contact: not prepared for wear indicator
• Supplementary Article/Supplementary Info: with accessories
• Brake System: TRW
• Packing Type: Box
• Thickness 1 [mm]: 14.3
• WVA Number: 23177
• Packaging length [cm]: 15
• Packaging width [cm]: 10.5
• Packaging height [cm]: 4.3
• Manufacturer: JURID

• Fitting Position: Front Axle
• Construction Year from: 05.1996
• Width [mm]: 155
• Thickness [mm]: 19
• Height 1 [mm]: 59
• Height 2 [mm]: 62
• Wear Warning Contact: incl. wear warning contact
• Supplementary Article/Supplementary Info: without accessories
• Brake System: Teves
• Warning Contact Length [mm]: 211
• Supplementary Article/Info 2: with piston clip
• directional:
• Number of wear indicators [per axle]: 2
• WVA Number: 23289, 21637
• Manufacturer: BREMBO
• Name: BR P 23 077

• Fitting Position: Front Axle
• Construction Year to: 03.1996
• Manufacturer Restriction: TRW
• Width [mm]: 129.9
• Height [mm]: 58.9
• Thickness [mm]: 19
• Wear Warning Contact: incl. wear warning contact
• Supplementary Article/Supplementary Info: with accessories
• Supplementary Article/Info 2: with brake caliper screws
• Test Mark: E1 90R 01024/359
• Manufacturer: TRW

SVHC: No information available, please contact the manufacturer!

• Driven Units: Balance shaft
• Number of Teeth: 97
• Packaging length [cm]: 25.5
• Packaging width [cm]: 16
• Packaging height [cm]: 3
• Weight [kg]: 0.122
• Width [mm]: 15
• Tooth Pitch [mm]: 9.525
• Manufacturer: CONTITECH

• Construction Year from: 04.1995
• Fitting Position: Front Axle
• Brake System: ATE
• Width 1 [mm]: 155
• Height 1 [mm]: 62
• Width 2 [mm]: 156
• Height 2 [mm]: 59
• Thickness [mm]: 19
• Wear Warning Contact: incl. wear warning contact
• Number of wear indicators [per axle]: 2
• Supplementary Article/Supplementary Info: Photo corresponds to scope of supply
• Test Mark: ECE R90 APPROVED
• Manufacturer: ZIMMERMANN

• Construction Year to: 12.1997
• Driven Units: Balance shaft
• Tensile Cord Material: Fiberglass
• Belt Material: HNBR (hydrogenated nitrile butadiene rubber)
• Colour: black
• Number of Teeth: 97
• Width [mm]: 15
• Tooth Pitch [mm]: 9.525
• Length [mm]: 924
• Manufacturer: GATES

• Fitting Position: Front Axle
• Construction Year from: 05.1996
• Width [mm]: 155
• Thickness [mm]: 19
• Height 1 [mm]: 59
• Height 2 [mm]: 62
• Wear Warning Contact: incl. wear warning contact
• Supplementary Article/Supplementary Info: without accessories
• Brake System: Teves
• Warning Contact Length [mm]: 211
• directional:
• Number of wear indicators [per axle]: 2
• WVA Number: 21637, 23289
• Name: BR P 23 077X
• Manufacturer: BREMBO

General Information: Brembo Xtra: the perfect brake pad for Brembo Xtra and Brembo Max brake discs.