• Oxygen Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Oxygen Sensor: Regulating Probe
• Number of circuits: 4
• Manufacturer: KAMOKA

• Construction Year to: 02.2010
• Oxygen Sensor: Diagnostic Probe
• Fitting Position: Front
• Length [mm]: 400
• Number of connectors: 4
• Manufacturer: VERNET

• Construction Year to: 06.2010
• Oxygen Sensor: Heated
• Number of pins: 4
• Cable Length [mm]: 670
• for article number: 81029E
• Quality: OE EQUIVALENT
• for OE number: 466016355182
• Manufacturer: MEAT&DORIA

• Oxygen Sensor: Oxygen Sensor
• Voltage [V]: 12
• Guarantee: 3 years guarantee
• Number of circuits: 4
• Weight [kg]: 0.09
• Resistor [Ohm]: 9
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Conductor Number: 4
• Resistor [Ohm]: 6
• Length [mm]: 340
• Number of circuits: 4
• Cable Length [mm]: 340
• Oxygen Sensor: Heated
• Name: LAMBDA ANDUR
• Manufacturer: MAG

• Engine Code: SPJA, SPJC
• Construction Year to: 07.2009, 11.2012
• Oxygen Sensor: Diagnostic Probe, Regulating Probe, Finger probe
• Block Separation:
• Construction Year from: 04.2010
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Transmission Type: Manual Transmission
• Name: LAMBDA ANDUR
• Manufacturer: MAX

Fitting Position: before catalytic converter, after catalytic converter

• Construction Year to: 08.2009
• Transmission Type: Manual Transmission
• for OE number: 1746710
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 103
• Gross Weight [g]: 152
• Manufacturer: DENSO
• Name: DN DOX-0119
• Quality class: Q

Oxygen Sensor: Regulating Probe, Heated, Finger probe, Oxygen Sensor Additional information: "Tootja: DENSO
ESCORT VII SEDAN (GA
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
ESCORT VII SEDAN (GA
(kvaliteediklass: Q)"

• Oxygen Sensor: Diagnostic Probe, Oxygen Sensor
• Construction Year to: 02.2010
• Engine Code: SPJA, SPJC
• Voltage [V]: 12
• Length [mm]: 300
• Guarantee: 3 years guarantee
• Number of circuits: 4
• Weight [kg]: 0.1
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV002

• Engine Code: SPJA, SPJE, SPJC
• Oxygen Sensor: Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 400
• Weight [kg]: 0.094
• for OE number: CA09-18-861
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Oxygen Sensor: Oxygen Sensor
• Voltage [V]: 12
• Length [mm]: 393
• Guarantee: 3 years guarantee
• Number of circuits: 4
• Weight [kg]: 0.1
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV048

• Construction Year from: 08.2009
• Transmission Type: Manual Transmission
• for OE number: 1800955
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 95
• Gross Weight [g]: 139
• Manufacturer: DENSO
• Name: DN DOX-0121
• Quality class: Q

Oxygen Sensor: Regulating Probe, Heated, Finger probe, Oxygen Sensor Additional information: "Tootja: DENSO
MONDEO I SEDAN (GBP)
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
MONDEO I SEDAN (GBP)
(kvaliteediklass: Q)"

• Engine Code: SPJA
• Construction Year to: 02.2010
• Fitting Position: after catalytic converter
• Cable Length [mm]: 300
• Conductor Number: 4
• Available as universal article as well, see article no.: 10.7008
• Number of circuits: 4
• Manufacturer: FACET

Oxygen Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased

• Engine Code: SPJA
• Construction Year to: 02.2010
• Fitting Position: after catalytic converter
• Cable Length [mm]: 300
• Conductor Number: 4
• Available as universal article as well, see article no.: 1.997.008
• Number of circuits: 4
• Name: EP 1.997.687
• Manufacturer: EPS

Oxygen Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased

• Construction Year to: 02.2010
• Oxygen Sensor: Diagnostic Probe, Planar probe, Heated
• Fitting Position: after catalytic converter
• Cable Length [mm]: 350
• Name: DE ES21085-12B1
• Manufacturer: DELPHI

• Construction Year to: 06.2010
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 430
• Number of pins: 4
• Oxygen Sensor: Finger probe, Thread pre-greased
• Weight [kg]: 0.129
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: SPJA, SPJE, SPJC
• Oxygen Sensor: Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 400
• Weight [kg]: 0.094
• for OE number: CA09-18-861
• Name: SW 33 10 3762
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Construction Year from: 09.2009
• Oxygen Sensor: Regulating Probe, Planar probe, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 385
• Manufacturer: DELPHI ELEKTRONIKA

• Construction Year to: 02.2010
• Oxygen Sensor: Diagnostic Probe, Planar probe, Heated
• Fitting Position: after catalytic converter
• Cable Length [mm]: 295
• Name: DE ES21370-12B1
• Manufacturer: DELPHI

• Engine Code: SPJA, SPJC, RTJA, RTJB, SPJE
• Construction Year to: 03.2010
• Oxygen Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 500
• Available as universal article as well, see article no.: F00HL00351
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Fitting Position: after catalytic converter
• Cable Length [mm]: 339
• Oxygen Sensor: Planar probe, Heated
• Manufacturer: DELPHI
• Name: DE ES20318-12B1

• Construction Year to: 08.2009
• Oxygen Sensor: Diagnostic Probe
• Voltage [V]: 12
• Length [mm]: 400
• Guarantee: 3 years guarantee
• Number of circuits: 4
• Weight [kg]: 0.12
• Resistor [Ohm]: 6
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Oxygen Sensor: Oxygen Sensor
• Cable Length [mm]: 290
• Alternatively:
• Number of circuits: 4
• Alternative Repair Kit: 570112
• Manufacturer: ERA

• Engine Code: SPJA, SPJC, RTJA, RTJB, SPJE
• Construction Year to: 03.2010
• Oxygen Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Manufacturer: BOSCH

• Engine Code: SPJA
• Construction Year to: 08.2009
• Fitting Position: before catalytic converter
• Cable Length [mm]: 350
• Conductor Number: 4
• Available as universal article as well, see article no.: 10.7008
• Number of circuits: 4
• Manufacturer: FACET

Oxygen Sensor: Regulating Probe, Heated, Planar probe, Thread pre-greased

• Engine Code: SPJA
• Construction Year to: 08.2009
• Fitting Position: before catalytic converter
• Cable Length [mm]: 350
• Conductor Number: 4
• Available as universal article as well, see article no.: 1.997.008
• Number of circuits: 4
• Name: LAMBDA ANDUR
• Manufacturer: EPS

Oxygen Sensor: Regulating Probe, Heated, Planar probe, Thread pre-greased

• Line insulation design: with silicone-coated woven-fibre insulation
• Oxygen Sensor: Planar probe, Heated, Thread pre-greased
• Supplementary Article/Info 2: without plug
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Manufacturer: VEMO GERMANY

Fitting Position: before catalytic converter, after catalytic converter General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: SPJA, SPJE, SPJC
• Oxygen Sensor: Heated, Diagnostic Probe
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Fitting Position: after catalytic converter
• Cable Length [mm]: 390
• Weight [kg]: 0.112
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Construction Year from: 08.2009
• Transmission Type: Manual Transmission
• for OE number: 1800955, 1113382
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 480
• Number of pins: 4
• Weight [g]: 96
• Gross Weight [g]: 126
• Manufacturer: DENSO

Oxygen Sensor: Regulating Probe, Heated, Finger probe, Oxygen Sensor Additional information: "Tootja: DENSO
MONDEO I SEDAN (GBP)
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
MONDEO I SEDAN (GBP)
(kvaliteediklass: Q)"

• Engine Code: SPJA, SPJC, RTJA, RTJB, SPJE
• Construction Year to: 07.2009, 11.2012
• Oxygen Sensor: Diagnostic Probe, Regulating Probe
• Transmission Type: Manual Transmission
• Block Separation:
• Construction Year from: 04.2010
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

Fitting Position: after catalytic converter, before catalytic converter

• Construction Year to: 06.2010
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 750
• Number of pins: 4
• Oxygen Sensor: Planar probe, Thread pre-greased
• Weight [kg]: 0.151
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year from: 03.2010
• Oxygen Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Length [mm]: 400
• Technical Information Number: Universal 77015
• Manufacturer: FAE

• Oxygen Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Construction Year to: 02.2010
• Length [mm]: 350
• Number of pins: 4
• Technical Information Number: Universal 77004
• Manufacturer: FAE

• Construction Year to: 08.2009
• Oxygen Sensor: Regulating Probe, Finger probe, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 370
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Construction Year from: 09.2009
• Oxygen Sensor: Regulating Probe, Heated
• Fitting Position: Exhaust Manifold
• Emission Standard: Euro 5
• Number of pins: 4
• Cable Length [mm]: 280
• for article number: 81676E
• Quality: OE EQUIVALENT
• for OE number: 1619640
• Name: Lambda andur
• Manufacturer: MD

• Construction Year from: 08.2009
• Transmission Type: Manual Transmission
• for OE number: 1743702
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 350
• Number of pins: 4
• Weight [g]: 89
• Gross Weight [g]: 119
• Manufacturer: DENSO
• Name: DN DOX-1726

Oxygen Sensor: Diagnostic Probe, Heated, Finger probe, Oxygen Sensor

• Construction Year to: 08.2009
• Transmission Type: Manual Transmission
• for OE number: 1746710
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 350
• Number of pins: 4
• Weight [g]: 96
• Gross Weight [g]: 126
• Manufacturer: DENSO
• Name: DN DOX-1720

Oxygen Sensor: Regulating Probe, Heated, Finger probe, Oxygen Sensor

• Construction Year from: 03.2010
• Oxygen Sensor: Diagnostic Probe
• Fitting Position: Front
• Quantity: 1
• Length [mm]: 400
• Number of connectors: 4
• Manufacturer: VERNET

• Construction Year to: 08.2009
• Engine Code: SPJA/SPJC
• Fitting Position: before catalytic converter
• Oxygen Sensor: Planar probe, Thread pre-greased, Heated
• Number of pins: 4
• Cable Length [mm]: 300
• Thread Size: M18x1,5
• Switch Pressure [bar]: 4
• Manufacturer: VALEO

• Construction Year to: 02.2010
• Oxygen Sensor: Diagnostic Probe
• Engine Code: RTJA, SPJA, SPJC
• Cable Length [mm]: 250
• Fitting Position: after catalytic converter
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PA358066981

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Construction Year to: 08.2009
• Oxygen Sensor: Regulating Probe, Heated
• Engine Code: RTJA, SPJA, SPJC
• Fitting Position: before catalytic converter
• Cable Length [mm]: 30
• Number of pins: 4
• Supplementary Article/Info 2: with heat shield
• Assy./disassy. by qualified personnel required!:
• Name: Lambda andur
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Construction Year from: 09.2009
• Oxygen Sensor: Regulating Probe, Heated
• Fitting Position: before catalytic converter
• Engine Code: RTJA, SPJA, SPJC
• Cable Length [mm]: 350
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PA358103381

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Oxygen Sensor: Regulating Probe, Diagnostic Probe
• Number of pins: 4
• Cable Length [mm]: 270
• for OE number: 466016355037
• Name: Lambda andur
• Manufacturer: MD