• Construction Year to: 07.1992
• Fitting Position: Left
• Vehicle Identification Number (VIN) to: N-300 000
• Exhaust System: for pre-catalytic converter
• for OE number: 048906265
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 521
• Number of pins: 3
• Weight [g]: 100
• Gross Weight [g]: 130
• Manufacturer: DENSO

Oxygen Sensor: Regulating Probe, Heated, Finger probe, Oxygen Sensor Additional information: "Tootja: DENSO
100 (4A, C4), 12.90-
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
100 (4A, C4), 12.90-
(kvaliteediklass: Q)"

Manufacturer: MAGNETI MARELLI

• Thread Size: M 10x1
• Number of pins: 2
• Housing Colour: white
• Manufacturer: FAE

• Number of pins: 3
• Socket colour: blue
• Fabrication Number: ESS-AU-001
• Manufacturer: NTY

• General Information: temperature sensor
• Manufacturer: VIKA

• Cable Length [mm]: 730
• Manufacturer: KAMOKA

• Number of pins: 3
• Socket colour: green
• Fabrication Number: ESS-AU-000
• Manufacturer: NTY

• Engine Code: AAH
• Length [mm]: 37
• Weight [kg]: 0.02
• Supplementary Article/Info 2: with seal ring
• for OE number: 025 906 041 A
• Supplementary Article/Supplementary Info: with gasket/seal
• Colour Coding: blue
• Number of pins: 2
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 3
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Engine Code: AAH
• Number of pins: 2
• Colour: white
• Thread Size: M10x1
• Spanner Size: 19
• Manufacturer: FACET

• Cable Length [mm]: 520
• Number of pins: 3
• Colour: blue, black
• Manufacturer: DELLO AUTOMEGA

• Engine Code: AAH
• Number of pins: 2
• Colour: white
• Thread Size: M10x1
• Spanner Size: 19
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• General Information: temperature sensor
• Manufacturer: VIKA

• Number of pins: 3
• Supplementary Article/Info 2: with cable
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Engine Code: AAH
• Sensor Type: Active sensor
• Manufacturer: KAMOKA

• Housing Colour: white
• Thread Size: M10 x 1,0
• Number of pins: 2
• Supplementary Article/Supplementary Info: with gasket/seal
• Temperature range [°C]: 25, 80
• Power [W]: 0.06
• Manufacturer: METZGER

• Height [mm]: 37
• Diameter [mm]: 90
• Length [mm]: 835
• General Information: knock sensor
• Manufacturer: VIKA

• Engine Code: AAH
• Colour: green
• Cable Length [mm]: 800
• Name: DETONATSIOONIANDUR
• Manufacturer: MAX

Manufacturer: MAGNETI MARELLI

• Number of pins: 3
• Connector Shape: rectangular
• Cable Length [mm]: 550
• for OE number: 054905377
• Manufacturer: MEAT&DORIA

Manufacturer: MAGNETI MARELLI

• Cable Length [mm]: 520
• Number of pins: 3
• Weight [kg]: 0.08
• Manufacturer: ERA

• Opening Temperature [°C]: 120
• Number of pins: 3
• Weight [kg]: 0.03
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: AAH
• Sensor Type: Hall Sensor
• Supplementary Article/Supplementary Info: with holder
• Number of pins: 3
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: MEY

• Number of pins: 3
• Colour: black
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Cable Length [mm]: 535
• Number of pins: 3
• Housing Colour: blue
• Lisainfo: Knock sensor
• Additional information: Knock sensor

• Sensor Type: Hall Sensor
• Connector Shape: rectangular
• Number of pins: 3
• Supplementary Article/Info 2: without cable
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Engine Code: AAH
• Number of pins: 3
• Connector Shape: rectangular
• Cable Length [mm]: 800
• for OE number: 054905377A
• Manufacturer: MEAT & DORIA

• Engine Code: AAH
• Number of pins: 3
• Weight [kg]: 0.065
• Manufacturer: ERA

• Oxygen Sensor: Regulating Probe
• Number of circuits: 4
• Manufacturer: KAMOKA

• Oxygen Sensor: Regulating Probe
• Number of circuits: 3
• Manufacturer: KAMOKA

• Oxygen Sensor: Regulating Probe, Oxygen Sensor
• Construction Year to: 07.1992
• Voltage [V]: 12
• Number of circuits: 3
• Weight [kg]: 0.08
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: ENERGY

• Engine Code: AAH
• Observe dimensions:
• Manufacturer: BOSCH

• for OE number: 054 905 377 G
• Width [mm]: 91
• Height [mm]: 37
• Length [mm]: 834
• Weight [kg]: 0.075
• Guarantee: 3 years guarantee
• Housing material: Plastic
• Socket colour: blue
• Operating Mode: Electric
• Voltage [V]: 12
• Supplementary Article/Info 2: with cable
• Number of pins: 3
• Connector Shape: rectangular
• Cable Length [mm]: 535
• Sensor Type: Piezoelectric Sensor
• Manufacturer: AT AUTOTEILE GERMANY

General Information: Products and spare parts supplied by us are only intended for the designated use. Installation may only be carried out by trained specialist personnel. Our products are not always supplied with installation instructions. Improper installation or inappropriate use may lead to the exclusion of warranty.

• Plug housing design: Plug sleeve housing
• Manufacturer Restriction: Alfa Romeo, Fiat, VAG
• Number of pins: 2
• Cable Length [mm]: 250
• Cable Cross Section [mm²]: 1
• Supplementary Article/Supplementary Info: with socket housing, with gaskets/seals
• Supplementary Article/Info 2: with pipe
• Temperature range from [°C]: -25
• Temperature range to [°C]: +140
• Cable insulation material: Silicone
• SVHC: No SVHC present!
• Manufacturer: HBE

Name: Kaabli remondikomplekt, jahutusvedeliku temperatuuri andur

• Engine Code: AAH
• Colour: green
• Name: DETONATSIOONIANDUR
• Manufacturer: BOS

• Cable Length [mm]: 550
• Number of pins: 3
• Housing Colour: blue
• Manufacturer: FAE

• Technical Information Number: Universal
• Overall Length [mm]: 315
• Number of pins: 3
• Oxygen Sensor: Regulating Probe
• Manufacturer: JAPKO

• Technical Information Number: Universal
• Overall Length [mm]: 315
• Number of pins: 3
• Oxygen Sensor: Regulating Probe
• Manufacturer: ASHIKA

• Sensor Type: Piezoelectric Sensor
• Cable Length [mm]: 540
• Number of pins: 3
• Name: Detonatsiooniandur
• Manufacturer: MEY

• Oxygen Sensor: Regulating Probe, Oxygen Sensor
• Construction Year to: 07.1992
• Voltage [V]: 12
• Guarantee: 3 years guarantee
• Number of circuits: 3
• Weight [kg]: 0.08
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Engine Code: AAH
• Colour: blue
• Name: DETONATSIOONIANDUR
• Manufacturer: BOS

• for OE number: 078 906 265
• Oxygen Sensor: Heated
• Name: Lambda andur
• Manufacturer: TRU

• Diameter [mm]: 90
• Length [mm]: 570
• Height [mm]: 37
• Cable Length [mm]: 535
• Weight [kg]: 0.07
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: AAH
• Construction Year to: 07.1992
• Oxygen Sensor: Regulating Probe, Heated
• Vehicle Identification Number (VIN) to: 8C..N..300000
• Number of circuits: 3
• Overall Length [mm]: 506
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Oxygen Sensor: Regulating Probe, Oxygen Sensor
• Construction Year to: 07.1992
• Voltage [V]: 12
• Length [mm]: 670
• Number of circuits: 3
• Weight [kg]: 0.11
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: ENERGY

• Cable Length [mm]: 800
• Number of pins: 3
• Housing Colour: green
• Manufacturer: FAE

• Plug housing design: Plug sleeve housing
• Manufacturer Restriction: BMW, Volvo, VAG
• Number of pins: 3
• Cable Length [mm]: 250
• Cable Cross Section [mm²]: 1
• Supplementary Article/Supplementary Info: with socket housing, with gaskets/seals
• Supplementary Article/Info 2: with pipe
• Temperature range from [°C]: -25
• Temperature range to [°C]: +140
• Cable insulation material: Silicone
• SVHC: No SVHC present!
• Manufacturer: HBE

Name: Kaabliparanduskomplekt, seadeelement- tulede ulatuse regul

• Oxygen Sensor: Regulating Probe, Oxygen Sensor
• Construction Year to: 07.1992
• Exhaust System: for pre-catalytic converter
• Voltage [V]: 12
• Guarantee: 3 years guarantee
• Number of circuits: 4
• Weight [kg]: 0.09
• Resistor [Ohm]: 13
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV913
• Manufacturer: ESEN SKV

• Oxygen Sensor: Regulating Probe
• Construction Year from: 08.1992
• Voltage [V]: 12
• Length [mm]: 710
• Guarantee: 3 years guarantee
• Number of circuits: 3
• Weight [kg]: 0.11
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV021

• Construction Year to: 07.1992
• Oxygen Sensor: Regulating Probe, Finger probe, Heated
• Vehicle Identification Number (VIN) to: 8C-N-300 000
• Cable Length [mm]: 490
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Construction Year to: 07.1992
• Fitting Position: Left
• Vehicle Identification Number (VIN) to: N-300 000
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 3
• Weight [g]: 95
• Gross Weight [g]: 144
• Manufacturer: DENSO
• Name: DN DOX-0116
• Lisainfo: DOX-0116 DENSO
• Additional information: DOX-0116 DENSO

Oxygen Sensor: Regulating Probe, Heated, Finger probe, Oxygen Sensor

• Construction Year from: 08.1992
• Fitting Position: Left
• Vehicle Identification Number (VIN) from: P-000 001
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 3
• Weight [g]: 95
• Gross Weight [g]: 144
• Manufacturer: DENSO
• Name: Lambda sensor
• Quality class: Q

Oxygen Sensor: Regulating Probe, Heated, Finger probe, Oxygen Sensor Additional information: "Tootja: DENSO
ESCORT IV KOMBI (AWF
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
ESCORT IV KOMBI (AWF
(kvaliteediklass: Q)"

• Oxygen Sensor: Regulating Probe, Oxygen Sensor
• Construction Year to: 07.1992
• Voltage [V]: 12
• Length [mm]: 670
• Guarantee: 3 years guarantee
• Number of circuits: 3
• Weight [kg]: 0.11
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV063
• Manufacturer: ESEN SKV

• Oxygen Sensor: Regulating Probe
• Voltage [V]: 12
• Length [mm]: 710
• Guarantee: 3 years guarantee
• Number of circuits: 3
• Weight [kg]: 0.16
• Resistor [Ohm]: 4.5
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV547
• Manufacturer: ESEN SKV

• Engine Code: AAH
• Vehicle Identification Number (VIN) to: ******8C*N*300000
• Oxygen Sensor: Heated, Regulating Probe
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 3
• Cable Length [mm]: 500
• Weight [kg]: 0.098
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Construction Year from: 07.1993
• Vehicle Identification Number (VIN) to: 8C-N-300000
• Oxygen Sensor: Heated
• Length [mm]: 500
• Number of pins: 3
• Technical Information Number: Universal 77003
• Manufacturer: FAE

• Engine Code: AAH
• Manufacturer: EPS

• Oxygen Sensor: Diagnostic Probe
• General Information: lambda probe; 4 wire
• Manufacturer: VIKA

• Engine Code: AAH, AFC
• Vehicle Identification Number (VIN) from: 8C-P-000001
• Line insulation design: with silicone-coated woven-fibre insulation
• Supplementary Article/Info 2: without plug
• Number of pins: 4
• for OE number: V99760001
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Length [mm]: 350
• Fitting Position: after catalytic converter
• Manufacturer: VEMO GERMANY

Oxygen Sensor: Regulating Probe, Finger probe, Heated, Thread pre-greased General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Vehicle Identification Number (VIN) from: 8C-P-191968
• Number of pins: 3
• Housing Type: with housing
• Manufacturer: JP GROUP
• Lisainfo: Air Mass Sensor
• Additional information: Air Mass Sensor

• Engine Code: AAH
• Construction Year to: 07.1992
• Oxygen Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Vehicle Identification Number (VIN) to: 8C..N..300 000
• Block Separation:
• Construction Year from: 08.1992
• Vehicle Identification Number (VIN) from: 8C..P..000 001
• Number of circuits: 3
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Engine Code: AAH
• Construction Year from: 08.1992
• Oxygen Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Vehicle Identification Number (VIN) from: 8C..P..000 001
• Number of circuits: 3
• Overall Length [mm]: 726
• Available as universal article as well, see article no.: 0258986502
• Recommended change interval [km]: 160,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Engine Code: AAH
• Construction Year to: 07.1992
• Oxygen Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Vehicle Identification Number (VIN) to: 8C..N..300 000
• Number of circuits: 3
• Overall Length [mm]: 506
• Available as universal article as well, see article no.: 0258986502
• Recommended change interval [km]: 160,000
• Manufacturer: BOSCH

• Name: OHUMASSIMOOTJA
• Manufacturer: MAG

• Vehicle Identification Number (VIN) from: 8C Z-N-000 001, 8C-P-190 001
• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 3
• Manufacturer: BREMI