• Fitting Position: Rear Axle, Left, Right, Wheel Side
• Number of Teeth: 48
• Width [mm]: 10
• Inner Diameter [mm]: 69
• Outer Diameter [mm]: 97
• Supplementary Article/Info 2: with integrated magnetic sensor ring
• Fabrication Number: NZA-ME-000
• Manufacturer: NTY
• Name: NTY NZA-ME-000

• Fitting Position: Front Axle Left, Front Axle Right
• Sensor Type: Hall Sensor
• Manufacturer: JP GROUP
• Lisainfo: Sensor, wheel speed
• Additional information: Sensor, wheel speed

• Fitting Position: Front Axle both sides
• Inner Diameter [mm]: 46.5
• Outer Diameter [mm]: 68.1
• Thickness [mm]: 9.5
• Supplementary Article/Info 2: Magnetic
• Number of Teeth: 96
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Fitting Position: Front Axle Left, Front Axle Right
• Fabrication Number: HCA-ME-002

• Fitting Position: Front Axle
• Sensor Type: Hall Sensor
• Number of pins: 2
• Cable Length [mm]: 565
• Manufacturer: ABAKUS DEPO/LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis.

• Fitting Position: Rear Axle Right
• Sensor Type: Hall Sensor
• Number of pins: 2
• Cable Length [mm]: 1,040
• Manufacturer: ABAKUS DEPO/LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis.

• Fitting Position: Rear Axle Left
• Sensor Type: Hall Sensor
• Number of pins: 2
• Cable Length [mm]: 1,125
• Manufacturer: JP GROUP
• Lisainfo: Sensor, wheel speed
• Additional information: Sensor, wheel speed

• Fitting Position: Rear Axle Right
• Sensor Type: Hall Sensor
• Number of pins: 2
• Cable Length [mm]: 970
• Manufacturer: JP GROUP
• Lisainfo: Sensor, wheel speed
• Additional information: Sensor, wheel speed

• Fitting Position: Rear Axle Left
• Fabrication Number: HCA-ME-000
• paired article number: HCA-ME-001
• Manufacturer: NTY

• Fitting Position: Rear Axle Right
• Fabrication Number: HCA-ME-001
• paired article number: HCA-ME-000
• Manufacturer: NTY

• Sensor Type: Active sensor
• Required quantity: 1
• Cable Length [mm]: 970
• Number of pins: 2
• Fitting Position: Rear Axle Right
• paired article number: 20-0366
• Name: Andur, rattap””rete arv
• Manufacturer: MAX

• Sensor Type: Active sensor
• Required quantity: 1
• Cable Length [mm]: 1,125
• Number of pins: 2
• Fitting Position: Rear Axle Left
• paired article number: 20-0367
• Name: Andur, rattap””rete arv
• Manufacturer: MAX

• Fitting Position: Front Axle both sides, Front Axle
• Manufacturer Restriction: ABS-Ring magnetisch
• Outer Diameter [mm]: 68
• Inner Diameter [mm]: 47
• Width [mm]: 9.5
• Manufacturer: METZGER

• Sensor Type: Active sensor
• Required quantity: 2
• Cable Length [mm]: 565
• Number of pins: 2
• Fitting Position: Front Axle
• Name: ANDUR, RATTAP™™RETE ARV
• Manufacturer: MAX

• Fitting Position: Rear Axle Left
• for OE number: A2035401317
• Number of mounting bores: 1
• Manufacturer: MAGNETI MARELLI
• Name: MM MWSS071

• Fitting Position: Rear Axle Right
• Cable Length [mm]: 948
• for OE number: A2035401417
• Number of mounting bores: 1
• Manufacturer: MAGNETI MARELLI
• Name: MM MWSS070

• Fitting Position: Front Axle
• Cable Length [mm]: 565
• for OE number: A2035400417
• Number of pins: 2
• Number of mounting bores: 1
• Manufacturer: MAGNETI MARELLI
• Name: MM MWSS069

• Fitting Position: Rear Axle Right
• Length [mm]: 948
• Manufacturer: DENCKERMANN FILTRY

• Sensor Type: Active sensor
• Number of pins: 2
• Cable Length [mm]: 1,115
• Fitting Position: Rear Axle Left
• Manufacturer: AUTOFREN SEINSA
• Name: SE DS0110

• Fitting Position: Rear Axle Left
• Length [mm]: 1,102
• Manufacturer: DENCKERMANN FILTRY

• Fitting Position: Front Axle
• Required quantity: 2
• Length [mm]: 565
• Manufacturer: DENCKERMANN FILTRY

• Fitting Position: Front, Left, Right
• Plug housing design: Plug sleeve housing
• Cable insulation material: Silicone
• Cable Length [mm]: 500
• Manufacturer Restriction: BMW, Mercedes-Benz
• Socket Width [mm]: 2.8
• Number of pins: 2
• Cable Cross Section [mm²]: 1
• Contact surface: Silver-plated
• Supplementary Article/Supplementary Info: with socket housing, with gaskets/seals
• Supplementary Article/Info 2: with pipe
• Temperature range from [°C]: -25
• Temperature range to [°C]: +125
• SVHC: No SVHC present!
• Manufacturer: HBE

Name: Kaabli paranduskomplekt, v„ntvolli positsiooniandur

• Sensor Type: Active sensor
• Cable Length [mm]: 580
• Number of pins: 2
• Fitting Position: Front Axle Right, Front Axle Left
• Manufacturer: AUTOFREN SEINSA
• Name: SE DS0095

• Fitting Position: Rear Axle, Right, Rear Axle Right
• Braking/Drive Dynamics: for vehicles with ABS
• Rated Voltage [V]: 12
• Weight [kg]: 0.052
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Left Rear, Rear Axle Left
• Braking/Drive Dynamics: for vehicles with ABS
• Rated Voltage [V]: 12
• Weight [kg]: 0.058
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Front Axle
• Inner Diameter [mm]: 46.5
• Width [mm]: 9.5
• Outer Diameter [mm]: 68.1
• Supplementary Article/Info 2: with integrated magnetic sensor ring
• Number of pins: 96
• Name: ANDUR,ABS
• Manufacturer: TRI

• Construction Year from: 03.2003
• Fitting Position: Rear
• Length [mm]: 990
• Number of pins: 2
• Plug Type: Male
• Connector Shape: oval
• Voltage [V]: 12
• Weight [kg]: 0.09
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 06SKV134
• Manufacturer: ESEN SKV

• Fitting Position: Rear
• Length [mm]: 1,130
• Number of pins: 2
• Plug Type: Male
• Connector Shape: oval
• Voltage [V]: 12
• Weight [kg]: 0.08
• Colour: black
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 06SKV061
• Manufacturer: ESEN SKV

• Fitting Position: Front
• Length [mm]: 600
• Number of pins: 2
• Plug Type: Male
• Connector Shape: oval
• Voltage [V]: 12
• Weight [kg]: 0.04
• Colour: black
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 06SKV151
• Manufacturer: ESEN SKV

• Fitting Position: Rear Axle Left
• Overall Length [mm]: 1,180
• Length [mm]: 31
• Sensor Type: Active sensor
• Socket colour: black
• Cable Length [mm]: 1,110
• paired article number: 30239
• Weight [kg]: 0.06
• Manufacturer: A.B.S.

• Fitting Position: Rear Axle Right
• Overall Length [mm]: 1,040
• Length [mm]: 31
• Sensor Type: Active sensor
• Socket colour: black
• Cable Length [mm]: 970
• paired article number: 30238
• Weight [kg]: 0.06
• Manufacturer: A.B.S.

• Fitting Position: Front Axle
• Alternatively:
• Sensor Type: Active sensor
• Number of occupied pins: 2
• Cable Length [mm]: 650
• Name: ANDUR, RATTAP™™RETE ARV
• Manufacturer: DLP
• Quality class: PJ

• Required quantity: 1
• Fitting Position: Rear Axle Right
• Supplementary Article/Info 2: with cable
• Manufacturer: BREMI

• Required quantity: 2
• Fitting Position: Front Axle
• Supplementary Article/Info 2: with cable
• Manufacturer: BREMI

• Fitting Position: Brake Booster
• Brake System: ATE
• Manufacturer: ATE

• Fitting Position: Front Axle
• Overall Length [mm]: 690
• Length [mm]: 31
• Sensor Type: Active sensor
• Socket colour: black
• Cable Length [mm]: 610
• paired article number: 30193
• Weight [kg]: 0.09
• Manufacturer: A.B.S.

• Required quantity: 1
• Fitting Position: Rear Axle Left
• Supplementary Article/Info 2: with cable
• Manufacturer: BREMI

• Sensor Type: Active sensor
• Cable Length [mm]: 1,125
• Number of pins: 2
• Fitting Position: Rear Axle Left
• paired article number: 014 899 0057
• Name: ANDUR, RATTAP™™RETE ARV
• Manufacturer: MEY

• Sensor Type: Active sensor
• Cable Length [mm]: 970
• Number of pins: 2
• Fitting Position: Rear Axle Right
• paired article number: 014 899 0056
• Name: ANDUR, RATTAP™™RETE ARV
• Manufacturer: MEY

• Fitting Position: Rear Axle Right
• Required quantity: 1
• Cable Length [mm]: 1,000
• Fitting Depth [mm]: 31.2
• Number of pins: 2
• Name: ANDUR, RATTAP™™RETE ARV
• Manufacturer: TRI

• Fitting Position: Rear Axle Left
• Required quantity: 1
• Cable Length [mm]: 1,155
• Fitting Depth [mm]: 31.2
• Number of pins: 2
• Name: ANDUR, RATTAP™™RETE ARV
• Manufacturer: TRI

• Cable Length [mm]: 1,000
• Fitting Position: Rear Axle Right
• Sensor Type: Active sensor
• Number of pins: 2
• Manufacturer: FAE

• Fitting Position: Rear Axle Left
• Sensor Type: Active sensor
• Number of occupied pins: 2
• Cable Length [mm]: 1,181
• Name: ANDUR, RATTAP™™RETE ARV
• Manufacturer: DLP

• Fitting Position: Right, Left, Front Axle
• Cable Length [mm]: 608
• Name: SN ASB151.28
• Manufacturer: NTN-SNR

• Number of pins: 2
• Sensor Type: Active sensor
• Cable Length [mm]: 960
• Fitting Position: Rear Axle Right
• Manufacturer: AUTOFREN SEINSA
• Name: SE DS0111

• Fitting Position: Rear Axle Right
• Sensor Type: Active sensor
• Number of occupied pins: 2
• Cable Length [mm]: 1,030
• Name: ANDUR, RATTAP™™RETE ARV
• Manufacturer: DLP

• Fitting Position: Left, Rear Axle, Front Axle
• Cable Length [mm]: 1,154
• Manufacturer: SNR /NTN-SNR/

• Fitting Position: Right, Rear Axle, Front Axle
• Cable Length [mm]: 1,000
• Manufacturer: SNR /NTN-SNR/

• paired article number: 10 93 0033
• Number of connectors: 2
• Outer Length [mm]: 1,192
• Fitting Position: Rear Axle Left
• Weight [kg]: 0.058
• Name: SW 10 93 0032
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: OM 611.962
• Fitting Position: Front Axle
• Warranty: 5 years warranty
• Manufacturer: HUCO

• Fitting Position: Front Axle
• Required quantity: 2
• Length [mm]: 565
• MAPP code available:
• Manufacturer: ATE

• Fitting Position: Front Axle
• Required quantity: 2
• Cable Length [mm]: 580
• Fitting Depth [mm]: 31
• Name: ANDUR, RATTAP™™RETE ARV
• Manufacturer: TRI

• Sensor Type: Active sensor
• Cable Length [mm]: 590
• Number of pins: 2
• Fitting Position: Front Axle
• Name: ANDUR, RATTAP™™RETE ARV
• Manufacturer: MEY

• Fitting Position: Front Axle
• Sensor Type: Active sensor
• Length [mm]: 565
• Manufacturer: TRW

SVHC: No information available, please contact the manufacturer!

• Fitting Position: Rear Axle Right
• Sensor Type: Active sensor
• Length [mm]: 1,040
• paired article number: GBS1910
• Manufacturer: TRW

SVHC: No information available, please contact the manufacturer!

• Fitting Position: Rear Axle Left
• Sensor Type: Active sensor
• Length [mm]: 1,190
• paired article number: GBS1909
• Manufacturer: TRW

SVHC: No information available, please contact the manufacturer!

• Fitting Position: Front Axle
• Sensor Type: Active sensor
• Supplementary Article/Info 2: with cable
• Overall Length [mm]: 650
• Temperature range from [°C]: -40
• Temperature range to [°C]: 150
• Manufacturer: BOSCH

• Required quantity: 2
• Voltage [V]: 12
• Manufacturer Restriction: Teves
• Cable Length [mm]: 565
• Sensor Type: Hall Sensor
• Fitting Position: Front Axle
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Fitting Position: Rear Axle Left
• Sensor Type: Active sensor
• Supplementary Article/Info 2: with cable
• Overall Length [mm]: 1,190
• Temperature range from [°C]: -40
• Temperature range to [°C]: 150
• Manufacturer: BOSCH

• Fitting Position: Rear Axle Right
• Length [mm]: 948
• MAPP code available:
• Manufacturer: ATE

• Fitting Position: Rear Axle Left
• Length [mm]: 1,102
• MAPP code available:
• Manufacturer: ATE

• Fitting Position: Rear Axle Right
• Sensor Type: Active sensor
• Supplementary Article/Info 2: with cable
• Overall Length [mm]: 1,040
• Temperature range from [°C]: -40
• Temperature range to [°C]: 150
• Manufacturer: BOSCH

• Fitting Position: Brake Booster
• Connector Shape: D Shape
• Number of pins: 3
• for OE number: 163 540 12 17
• Brake System: ATE
• Weight [kg]: 0.064
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.