• Fitting Position: Left
• for OE number: 0015408917, 15407517
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 98
• Gross Weight [g]: 131
• Manufacturer: DENSO

Lambda Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
KLASA C KOMBI (S202)
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
KLASA C KOMBI (S202)
(kvaliteediklass: Q)"

• Number of pins: 2
• Connector Shape: oval
• Socket colour: black
• Sensor Type: NTC Sensor
• Fitting Depth [mm]: 23
• for OE number: A 000 905 07 00
• Manufacturer: MEAT&DORIA

Manufacturer: MAGNETI MARELLI

• for OE number: 005 153 50 28, 2E0 906 051 A
• Number of pins: 3
• Pressure from [kPA]: 10
• Pressure to [kPA]: 127
• Fabrication Number: ECM-ME-000
• Manufacturer: NTY

• Engine Code: M 112.916
• Name: EP 1.830.300
• Manufacturer: EPS

for article number: 1.880.588, 1.880.589, 1.880.590, 1.880.591, 1.880.592, 1.880.593, 1.880.594, 1.880.595, 1.880.596, 1.880.597, 1.880.598, 1.880.784, 1.880.847, 1.880.935

• Sensor Type: Hall Sensor
• Number of pins: 3
• Fitting Depth [mm]: 24.3
• Supplementary Article/Info 2: without cable
• Connector Shape: oval
• Fabrication Number: ECP-ME-000
• Manufacturer: NTY

• Fabrication Number: ESS-ME-000
• Manufacturer: NTY

• Height [mm]: 18.2
• Supplementary Article/Supplementary Info: with seal
• Number of pins: 2
• Weight [kg]: 0.021
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 3
• Colour: black
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Sensor Type: Active sensor
• for OE number: 05080346AA
• Manufacturer: KAMOKA

• Fabrication Number: ECP-ME-006
• Number of pins: 3
• Manufacturer: NTY

• for OE number: 003 153 8628
• Manufacturer: TRUCKTEC

Fabrication Number: ECP-ME-003

Manufacturer: MAGNETI MARELLI

• Thickness [mm]: 21, 18
• Inner Diameter [mm]: 8.3
• Outer Diameter [mm]: 45
• Number of connectors: 2
• Weight [kg]: 0.045
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Voltage [V]: 12
• Number of pins: 2
• Tightening Torque [Nm]: 20
• Supplementary Article/Info 2: without cable
• Corresponds to the original part in colour: black
• Plug Type: Blade Terminal
• Connector Shape: rectangular
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PG013114371
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Thickness [mm]: 21, 18
• Inner Diameter [mm]: 8.3
• Outer Diameter [mm]: 45
• Number of connectors: 2
• Weight [kg]: 0.045
• Name: SW 10 93 7269
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of pins: 3
• Pressure from [kPA]: 10
• Manufacturer: DELPHI
• Name: DE PS10140

• Construction Year to: 06.2005
• Manufacturer: BOSCH

• Number of pins: 3
• Pressure from [kPA]: 10
• Pressure to [kPA]: 127
• for OE number: 005 153 50 28, 2E0 906 051 A
• Quality: OE EQUIVALENT
• Manufacturer: MEAT&DORIA

• Number of pins: 3
• for OE number: 005 153 50 28
• Manufacturer: TOPRAN HANS PRIES

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Alternatively:
• Number of pins: 3
• Fitting Depth [mm]: 24
• Supplementary Article/Info 2: without cable
• Alternative Repair Kit: 550328
• Manufacturer: ERA

Manufacturer: FAST

• Housing Type: with housing
• Fabrication Number: EPP-CH-006
• Manufacturer: NTY

• Measuring Range from [kPa]: 15
• Measuring Range to [kPa]: 260
• Measuring Range from [V]: 0.4
• Measuring Range to [V]: 4.65
• Number of connectors: 3
• Manufacturer: VERNET

• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Quantity: 1
• Number of pins: 3
• Pressure from [kPA]: 21
• Manufacturer: DELPHI
• Name: DE PS10136

• Engine Code: M 112.916
• Required quantity: 1
• Switch Pressure [bar]: 2.5
• Pressure from [kPA]: 10
• Pressure to [kPA]: 265
• Output Voltage, from [V]: 0.314
• Output Voltage, up to [V]: 4.75
• Name: EP 1.993.102
• Manufacturer: EPS

• Number of pins: 5
• Housing Type: without housing
• Connector Shape: D Shape
• Manufacturer: ABAKUS DEPO/LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis.

• Engine Code: M 112.916
• alternative OE number: 0041536928
• Required quantity: 1
• Name: EP 1.953.387
• Manufacturer: EPS

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Fitting Position: after catalytic converter
• Fabrication Number: ESL-BM-009

• Construction Year to: 06.2005
• Sensor Type: Hall Sensor
• Alternatively:
• Number of pins: 3
• Fitting Depth [mm]: 24
• Manufacturer: ERA

• for OE number: 004 153 3028
• Manufacturer: TRUCKTEC

• Alternatively:
• Number of pins: 3
• Manufacturer: DELPHI
• Name: DE SS11033

• Height [mm]: 24.2
• Sensor Type: Hall Sensor
• Number of connectors: 3
• Manufacturer: VERNET

• Lambda Sensor: Regulating Probe, Diagnostic Probe
• Length [mm]: 330
• Fabrication Number: ESL-ME-001
• Manufacturer: NTY

• Number of pins: 2
• Manufacturer: DELPHI
• Name: DE AS10218

• Length [mm]: 35
• Width [mm]: 48.5
• Thickness [mm]: 43
• Number of connectors: 3
• Weight [kg]: 0.015
• for OE number: 005 153 50 28
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of pins: 3
• Pressure from [kPA]: 15
• Pressure to [kPA]: 260
• Manufacturer: FAE

• Quantity: 1
• Number of pins: 3
• Manufacturer: DELPHI
• Name: DE SS11151

• Lambda Sensor: Diagnostic Probe, Regulating Probe
• Length [mm]: 900
• Fabrication Number: ESL-ME-000
• Manufacturer: NTY

• Required quantity: 1
• alternative OE number: 0041536928
• Sensor Type: Hall Sensor
• Number of pins: 3
• Fitting Depth [mm]: 24.2
• Supplementary Article/Info 2: with seal ring, without cable
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead, 872-50-4; 1-Methyl-2-pyrrolidone
• Name: HE 6PU009168001
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Construction Year to: 06.2005
• Manufacturer: BOSCH

• Required quantity: 1
• Mounting Type: Bolted
• Number of pins: 3
• Supplementary Article/Supplementary Info: with seal
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Required quantity: 1
• Mounting Type: Bolted
• Number of pins: 3
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PP358152061
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Required quantity: 1
• Version: 2
• Height [mm]: 24
• Sensor Type: Hall Sensor
• Number of connectors: 3
• Manufacturer: VERNET

• Construction Year from: 09.2002
• Construction Year to: 12.2006
• Transmission Type: Automatic Transmission
• Fitting Position: Left, before catalytic converter
• Lambda Sensor: Regulating Probe, Thread pre-greased
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 650
• Connector Shape: round
• Conductor Number: 4
• Thread Size: M18 x 1,5
• Cable Length [mm]: 650
• Number of circuits: 4
• Weight [kg]: 0.11
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: M 112.916
• alternative OE number: 2729050043
• Required quantity: 1
• Name: EP 1.953.438
• Manufacturer: EPS

• Engine Code: M 112.916
• Left-/right-hand drive vehicles: for right-hand drive vehicles
• Lambda Sensor: Regulating Probe
• Fitting Position: Left
• Number of circuits: 4
• Supplementary Article/Info 2: without plug
• Manufacturer: ENERGY

• Construction Year to: 06.2005
• Quality class: PJ
• Name: Air flow sensor

• Construction Year from: 09.2002
• Construction Year to: 06.2005
• Voltage [V]: 12
• Housing Type: with housing
• Number of pins: 5
• Weight [kg]: 0.35
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 07SKV026

• Construction Year to: 12.2005
• Supplementary Article/Supplementary Info: with suction pipe
• Housing Type: with housing
• Number of pins: 5

• Construction Year from: 09.2002
• Construction Year to: 06.2005
• Number of pins: 5
• Housing Type: with housing
• Lisainfo: Air meter
• Additional information: Air meter

• Lambda Sensor: Regulating Probe, Lambda Sensor
• Construction Year to: 06.2005
• Exhaust System: before catalytic converter
• Voltage [V]: 12
• Length [mm]: 830
• Number of circuits: 4
• Weight [kg]: 0.11
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Construction Year from: 09.2002
• Construction Year to: 12.2006
• Transmission Type: Automatic Transmission
• Fitting Position: Left, before catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Conductor Number: 4
• Connector Shape: round
• Thread Size: M18 x 1,5
• Length [mm]: 550
• Cable Length [mm]: 570
• Left-/right-hand drive vehicles: for right-hand drive vehicles
• Lambda Sensor: Regulating Probe, Thread pre-greased
• Number of circuits: 4
• Weight [kg]: 0.15
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Right, after catalytic converter
• Lambda Sensor: Heated, Diagnostic Probe
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 460
• Weight [kg]: 0.086
• Name: SW 33 10 3200
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Construction Year from: 09.2002
• Construction Year to: 12.2006
• Transmission Type: Automatic Transmission
• Fitting Position: Left, before catalytic converter
• Lambda Sensor: Regulating Probe, Heated, Thread pre-greased
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 720
• Connector Shape: round
• Number of pins: 4
• Weight [kg]: 0.117
• for OE number: 002 540 08 17
• Socket colour: black
• Thread Size: M18 x 1,5
• Cable Length [mm]: 720
• Number of circuits: 4
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 12.2005
• for OE number: 003 153 97 28
• Sensor Type: Hall Sensor, Active sensor
• Supplementary Article/Info 2: for camshaft, without cable
• Required quantity: 1
• Operating Mode: Electric
• Supplementary Article/Supplementary Info: with seal
• Number of pins: 3
• Number of connectors: 3
• Rated Voltage [V]: 12
• Fitting Depth [mm]: 24
• Connector Shape: oval
• Colour Coding: grey
• Resistor [kOhm]: 145
• Temperature range from [°C]: -40
• Temperature range to [°C]: 150
• Weight [kg]: 0.027
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Resistor [Ohm]: 9
• Length [mm]: 900
• Conductor Number: 4
• Number of circuits: 4
• Cable Length [mm]: 900
• Lambda Sensor: Heated
• Manufacturer: MAGNETI MARELLI
• Name: MM OSM126

• Construction Year from: 09.2002
• Construction Year to: 06.2005
• Lambda Sensor: Regulating Probe, Planar probe
• Fitting Position: Exhaust Manifold
• Required quantity: 2
• Number of pins: 4
• Cable Length [mm]: 800
• Manufacturer: MEAT&DORIA

• Number of pins: 3
• Housing Colour: black
• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: without cable
• Manufacturer: FAE

• Construction Year to: 06.2005
• Lambda Sensor: Lambda Sensor
• Voltage [V]: 12
• Length [mm]: 660
• Number of circuits: 4
• Weight [kg]: 0.14
• Resistor [Ohm]: 9
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV643

• Construction Year from: 09.2002
• Construction Year to: 12.2006
• Transmission Type: Automatic Transmission
• Fitting Position: Left, before catalytic converter
• Lambda Sensor: Regulating Probe, Thread pre-greased
• Line insulation design: with silicone-coated woven-fibre insulation
• Thread Size: M18 x 1,5
• Conductor Number: 4
• Connector Shape: round
• Length [mm]: 880
• Cable Length [mm]: 870
• Number of circuits: 4
• Weight [kg]: 0.15
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Required quantity: 1
• alternative OE number: 0041536928
• Voltage [V]: 12
• Sensor Type: Hall Sensor
• Supplementary Article/Supplementary Info: with seal
• Number of pins: 3
• Number of mounting bores: 1
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

SVHC: 1317-36-8; Lead monoxide (lead oxide), 12060-00-3; Lead titanium trioxide, 7439-92-1; Lead Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Engine Code: M 112.916
• Left-/right-hand drive vehicles: for right-hand drive vehicles
• Fitting Position: Left
• Line insulation design: with silicone-coated woven-fibre insulation
• Number of pins: 4
• for OE number: V99760001
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Length [mm]: 350
• Exhaust System: after catalytic converter
• Manufacturer: VEMO GERMANY

Lambda Sensor: Regulating Probe, Finger probe, Heated, Thread pre-greased Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

Manufacturer: FAST

• Lambda Sensor: Regulating Probe, Planar probe, Heated
• Block Separation:
• Cable Length [mm]: 919
• Manufacturer: DELPHI
• Name: DE ES20174-12B1

Fitting Position: Left Front, before catalytic converter, Right Front Left-/right-hand drive vehicles: for left-hand drive vehicles, for right-hand drive vehicles

• Line insulation design: with silicone-coated woven-fibre insulation
• Lambda Sensor: Planar probe, Heated, Thread pre-greased
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Manufacturer: VEMO GERMANY

Fitting Position: both sides, before catalytic converter, after catalytic converter Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 06.2005
• Lambda Sensor: Regulating Probe, Diagnostic Probe
• Block Separation:
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Manufacturer: BOSCH

Fitting Position: before catalytic converter, Left, after catalytic converter, Right Left-/right-hand drive vehicles: for left-hand drive vehicles, for right-hand drive vehicles

• Fitting Position: Left
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 93
• Gross Weight [g]: 140
• Manufacturer: DENSO
• Name: DN DOX-0150
• Quality class: Q

Lambda Sensor: Regulating Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
(kvaliteediklass: Q)"

• Lambda Sensor: Regulating Probe
• Length [mm]: 650
• Technical Information Number: Universal 77015
• Manufacturer: FAE

Fitting Position: after catalytic converter, before catalytic converter

• Construction Year to: 12.2005
• Weight [kg]: 0.02
• for OE number: A 004 153 32 28
• Supplementary Article/Supplementary Info: with seal
• Number of pins: 3
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• for manufacturer exhaust norm: Standard EU4
• Lambda Sensor: Diagnostic Probe, Regulating Probe
• Length [mm]: 300
• Technical Information Number: Universal 77015
• Manufacturer: FAE

Fitting Position: after catalytic converter, before catalytic converter