• for OE number: MD348431
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 420
• Number of pins: 4
• Weight [g]: 88
• Gross Weight [g]: 121
• Manufacturer: DENSO

Lambda Sensor: Diagnostic Probe, Heated, Finger probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
SPACE GEAR (PA/B/D/V
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
SPACE GEAR (PA/B/D/V
(kvaliteediklass: Q)"

• for OE number: MD 091056
• Number of pins: 1
• Weight [kg]: 0.02
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

Manufacturer: MAGNETI MARELLI

• Engine Code: 4G13 (16V)
• Thread Size: 1/8 GAS
• Spanner Size: 13
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Fitting Position: Exhaust Side
• Transmission Type: 5-Speed Manual Transmission
• Fabrication Number: ECR-MS-001
• Manufacturer: NTY

• Thread Size: 3/8 x 19 BSP
• Colour: black
• Spanner Size: 19
• Number of pins: 2
• Weight [kg]: 0.042
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fabrication Number: ECP-HY-005
• Manufacturer: NTY

• Voltage [V]: 12
• Supplementary Article/Supplementary Info: without cable pull
• Number of pins: 3
• Weight [kg]: 0.03
• Operating Mode: Electric
• Warranty: 3 years warranty
• Name: CE 17SKV243
• Manufacturer: ESEN SKV

• Number of pins: 2
• Housing Colour: black
• Thread Size: 3/8x19 BSP
• Manufacturer: FAE

• Engine Code: 4G13 (16V)
• Thread Size: 3/8-GAS
• Spanner Size: 19
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 3
• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: without cable
• Housing Colour: black
• Name: CZUJNIK POO½ENIA WAKA ROZRZ. VOLVO S40 1,8 98-
• Manufacturer: BRM

• Supplementary Article/Info 2: without cable
• Sensor Type: Hall Sensor
• Number of pins: 3
• Name: Andur,Nukkvollipositsioon
• Manufacturer: MD

• Length [mm]: 58
• Number of connectors: 3
• Weight [kg]: 0.03
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: BLP
• Additional information: ADC47204
• Lisainfo: ADC47204

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Length [mm]: 57.5
• Number of connectors: 3
• Weight [kg]: 0.03
• Name: SW 90 93 2575
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

Manufacturer: MAGNETI MARELLI

• Engine Code: 4G13 (16V)
• Alternatively:
• Rotation Direction: Clockwise rotation
• Number of pins: 3
• Alternative Repair Kit: 550439
• Manufacturer: ERA

• Engine Code: 4G13 (16V)
• Sensor Type: Hall Sensor
• Number of pins: 3
• Voltage [V]: 12
• Name: Andur,Nukkvollipositsioon
• Manufacturer: MAX

• Lambda Sensor: Lambda Sensor, Thread pre-greased
• Fabrication Number: ESL-UV-001
• Manufacturer: NTY
• Name: NTY ESL-UV-001

• Check OE number:
• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: with seal ring
• Number of pins: 3
• Manufacturer: MEYLE

• Fitting Position: Front, after catalytic converter
• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-MS-010
• Manufacturer: NTY

• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Fabrication Number: ESL-MS-003
• Manufacturer: NTY

Fitting Position: Front, before catalytic converter, after catalytic converter Lambda Sensor: Regulating Probe, Diagnostic Probe, Thread pre-greased

• Engine Code: 4G13 (16V)
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: EPS

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Engine Code: 4G13 (16V)
• Number of pins: 4
• Manufacturer: ERA

• Number of pins: 3
• Supplementary Article/Info 2: for camshaft, without cable
• Required quantity: 1
• Sensor Type: Hall Sensor
• Supplementary Article/Supplementary Info: with seal
• Number of connectors: 3
• Rated Voltage [V]: 12
• Fitting Depth [mm]: 27
• Housing Colour: black
• Connector Shape: oval
• Number of mounting bores: 1
• Weight [kg]: 0.02
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Lambda Sensor
• Weight [kg]: 0.12
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY
• Name: CE 09SKV121

• Construction Year to: 06.2003
• Lambda Sensor: Regulating Probe, Lambda Sensor
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Lambda Sensor: Regulating Probe
• Number of pins: 4
• Cable Length [mm]: 630
• Manufacturer: MEAT&DORIA

• Lambda Sensor: Diagnostic Probe
• Engine Code: 4G13 (16V)
• Voltage [V]: 12
• Length [mm]: 420
• Number of circuits: 4
• Weight [kg]: 0.9
• Operating Mode: Electric
• Warranty: 3 years warranty
• Name: CE 09SKV024
• Manufacturer: ESEN SKV

• Lambda Sensor: Regulating Probe, Finger probe, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 340
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Exhaust System: for pre-catalytic converter
• Quality: OE
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 95
• Gross Weight [g]: 144
• Manufacturer: DENSO

Lambda Sensor: Regulating Probe, Heated, Finger probe, Lambda Sensor Additional information: "Tootja: DENSO
SPACE WAGON (N5/W),
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
SPACE WAGON (N5/W),
(kvaliteediklass: Q)"

• Number of pins: 3
• Sensor Type: Hall Sensor
• Fitting Depth [mm]: 27
• Quality: OE
• Manufacturer: METZGER

• Engine Code: 4G13 (16V)
• Line insulation design: with silicone-coated woven-fibre insulation
• Number of pins: 4
• for OE number: V99760001
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Length [mm]: 350
• Exhaust System: after catalytic converter
• Manufacturer: VEMO GERMANY

Lambda Sensor: Regulating Probe, Finger probe, Heated, Thread pre-greased Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 06.2003
• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Fitting Position: Front, Upper, after catalytic converter
• Lambda Sensor: Diagnostic Probe, Heated
• Required quantity: 1
• Cable Length [mm]: 410
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Name: Lambda andur
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Construction Year to: 06.2003
• Fitting Position: before catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Lambda Sensor: Planar probe, Heated, Thread pre-greased
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Manufacturer: VEMO GERMANY

Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Line insulation design: with silicone-coated woven-fibre insulation
• Number of pins: 4
• Connector Shape: angular
• Socket colour: black
• Number of circuits: 4
• Thread Size: M18 x 1,5
• Weight [kg]: 0.131
• for OE number: MD 351752
• Cable Length [mm]: 290
• Length [mm]: 400
• Number of connectors: 4
• Lambda Sensor: Heated, Thread pre-greased
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Line insulation design: with silicone-coated woven-fibre insulation
• Socket colour: black
• Number of circuits: 4
• Number of pins: 4
• Connector Shape: angular
• Thread Size: M18 x 1,5
• Weight [kg]: 0.115
• for OE number: MD 177969
• Cable Length [mm]: 350
• Length [mm]: 470
• Number of connectors: 4
• Lambda Sensor: Heated, Thread pre-greased
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Exhaust System: for pre-catalytic converter
• for OE number: 1588A020
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 390
• Number of pins: 4
• Weight [g]: 93
• Gross Weight [g]: 126
• Manufacturer: DENSO
• Name: DN DOX-0313

Lambda Sensor: Regulating Probe, Heated, Finger probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
COLT V (CJ/A), 09.95
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
COLT V (CJ/A), 09.95
(kvaliteediklass: Q)"

• Height [mm]: 27
• Sensor Type: Hall Sensor
• Number of connectors: 3
• Manufacturer: VERNET