• Number of pins: 2
• Manufacturer: JP GROUP
• Lisainfo: Sender Unit, coolant temperature
• Additional information: Sender Unit, coolant temperature

• Exhaust System: for pre-catalytic converter
• for OE number: MD183145
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 320
• Number of pins: 4
• Weight [g]: 93
• Gross Weight [g]: 123
• Manufacturer: DENSO

Lambda Sensor: Regulating Probe, Heated, Finger probe, Lambda Sensor Additional information: "Tootja: DENSO
GALANT V SEDAN (E5/A
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
GALANT V SEDAN (E5/A
(kvaliteediklass: Q)"

• Spanner Size: 13
• for OE number: 8342087703
• Manufacturer: KAMOKA

• Length [mm]: 59
• Housing Colour: black
• Spanner Size: 19
• Manufacturer: KAMOKA

• Spanner Size: 13
• Material: Brass
• Number of pins: 1
• Thread Size: 1/8" - 28
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX

• Fabrication Number: ECT-HY-000
• Manufacturer: NTY
• Name: NTY ECT-HY-000

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Number of pins: 1
• Spanner Size: 12
• Thread Size: 1/8
• for OE number: 4671065
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Fabrication Number: ECT-MS-000
• Name: NTY ECT-MS-000
• Manufacturer: NTY

• for OE number: MD 091056
• Number of pins: 1
• Weight [kg]: 0.02
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• External Thread Size: 1/8" - 28
• Spanner Size: 13
• Number of connectors: 1
• Material: Brass
• Weight [kg]: 0.01
• Manufacturer: SWAG
• Name: SW 81 92 8265

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thread Size: 3/8x19 BSP
• Manufacturer: VERNET

• External Thread Size: 1/8" - 28
• Spanner Size: 13
• Number of connectors: 1
• Material: Brass
• Weight [kg]: 0.01
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thread Size: 1/8 GAS
• Spanner Size: 13
• Number of pins: 1
• Manufacturer: ERA

Manufacturer: MAGNETI MARELLI

• Engine Code: 4G93 (DOHC 16V)
• Thread Size: 1/8 GAS
• Spanner Size: 13
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: rectangular
• Number of pins: 2
• Socket colour: black
• Spanner Size: 19
• Thread Size: 3/8
• for OE number: MD177572
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Thread Size: 1/8x28 BSPT
• Manufacturer: VERNET

• for OE number: MD149338, 39220 35520, MD-149338, 97036606
• Number of pins: 2
• Connector Shape: rectangular
• Socket colour: blue
• Thread Size: 3/8"-19BSP
• Sensor Type: NTC Sensor
• Spanner Size: 19 mm
• Manufacturer: MEAT&DORIA

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: rectangular
• Number of pins: 2
• Socket colour: white
• Spanner Size: 19
• Thread Size: 3/8
• for OE number: MD149338
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Thread Size: 3/8 x 19 BSP
• Colour: black
• Spanner Size: 19
• Number of pins: 2
• Weight [kg]: 0.042
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Mounting Type: Flat Plug-in Connector, Bolted
• Voltage [V]: 12
• Resistor [Ohm]: 628, 70
• Temperature range from [°C]: 25
• Temperature range to [°C]: 80
• Thread Size: 1/8 GAS
• Spanner Size: 13
• Sensor Type: NTC Sensor
• Number of pins: 1
• Housing Colour: black
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PT009107651
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Thread Size: 3/8 GAS
• Spanner Size: 19
• Number of pins: 2
• Manufacturer: ERA

• Number of connectors: 2
• Colour: black
• Weight [kg]: 0.066
• Manufacturer: BLUE PRINT

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Length [mm]: 59.7
• Spanner Size: 19
• Number of connectors: 2
• Colour: black
• Weight [kg]: 0.04
• Name: SW 80 93 2375
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Voltage [V]: 12
• Supplementary Article/Supplementary Info: without cable pull
• Number of pins: 3
• Weight [kg]: 0.03
• Operating Mode: Electric
• Warranty: 3 years warranty
• Name: CE 17SKV243
• Manufacturer: ESEN SKV

• Length [mm]: 59.7
• Spanner Size: 19
• Number of connectors: 2
• Colour: black
• Weight [kg]: 0.04
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: 4G93 (DOHC 16V)
• Thread Size: 3/8-GAS
• Spanner Size: 19
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Number of pins: 2
• Housing Colour: black
• Thread Size: 3/8x19 BSP
• Manufacturer: FAE

• Voltage [V]: 12
• Resistor [Ohm]: 2,080, 294
• Temperature range from [°C]: 25
• Temperature range to [°C]: 80
• Thread Size: 3/8 GAS
• Colour: black
• Spanner Size: 19
• Sensor Type: NTC Sensor
• Number of pins: 2
• Corresponds to the original part in colour: black
• Mounting Type: Vertical Screw Fitting
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PT009107121

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Fabrication Number: ECP-MS-017
• Manufacturer: NTY

• Lambda Sensor: Lambda Sensor, Thread pre-greased
• Fabrication Number: ESL-UV-001
• Manufacturer: NTY

• Lambda Sensor: Unheated
• Lisainfo: Lambda sensor
• Additional information: Lambda sensor

• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

Number of pins: 3

• Engine Code: 4G93 (DOHC 16V)
• Number of pins: 3
• Supplementary Article/Info 2: for camshaft, without cable
• Required quantity: 1
• Sensor Type: Hall Sensor
• Supplementary Article/Supplementary Info: with seal
• Number of connectors: 3
• Rated Voltage [V]: 12
• Fitting Depth [mm]: 27
• Housing Colour: black
• Connector Shape: oval
• Number of mounting bores: 1
• Weight [kg]: 0.02
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Regulating Probe, Lambda Sensor
• Construction Year to: 08.1995
• Exhaust System: before catalytic converter
• Voltage [V]: 12
• Number of circuits: 4
• Weight [kg]: 0.09
• Resistor [Ohm]: 13
• Operating Mode: Electric
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY
• Name: CE 09SKV913

• Engine Code: 4G93 (DOHC 16V)
• Construction Year to: 11.1995
• Lambda Sensor: Regulating Probe, Lambda Sensor
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Engine Code: 4G93 (DOHC 16V)
• Cable Length [mm]: 350
• Alternatively:
• Number of pins: 2
• Fitting Depth [mm]: 12
• Alternative Repair Kit: 550334
• Manufacturer: ERA

• Lambda Sensor: Lambda Sensor
• Weight [kg]: 0.12
• Warranty: 3 years warranty
• Name: CE 09SKV121
• Manufacturer: ESEN SKV

• Lambda Sensor: Regulating Probe
• Engine Code: 4G93
• Voltage [V]: 12
• Length [mm]: 320
• Number of circuits: 4
• Weight [kg]: 0.09
• Operating Mode: Electric
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY

• Exhaust System: for pre-catalytic converter
• Quality: OE
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 103
• Gross Weight [g]: 147
• Manufacturer: DENSO
• Lisainfo: DOX-0109 DENSO
• Additional information: DOX-0109 DENSO

Lambda Sensor: Regulating Probe, Heated, Finger probe, Lambda Sensor

• Engine Code: 4G93 Kat.
• Construction Year to: 11.1995
• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Engine Code: 4G93 (DOHC 16V)
• Line insulation design: with silicone-coated woven-fibre insulation
• Number of pins: 4
• for OE number: V99760001
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Length [mm]: 350
• Exhaust System: after catalytic converter
• Manufacturer: VEMO GERMANY

Lambda Sensor: Regulating Probe, Finger probe, Heated, Thread pre-greased Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.