• Vehicle type: I.O, Montero I.O, Pajero Pinin, Shogun Pinin
• Block Separation:
• Number of pins: 2
• Lisainfo: Sender Unit, coolant temperature
• Additional information: Sender Unit, coolant temperature

• Construction Year to: 06.2000
• for OE number: MR420649, MD348431
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 420
• Number of pins: 4
• Weight [g]: 88
• Gross Weight [g]: 121
• Manufacturer: DENSO

Lambda Sensor: Regulating Probe, Heated, Finger probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
SPACE GEAR (PA/B/D/V
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
SPACE GEAR (PA/B/D/V
(kvaliteediklass: Q)"

• Spanner Size: 13
• for OE number: 8342087703
• Manufacturer: KAMOKA

• Length [mm]: 59
• Housing Colour: black
• Spanner Size: 19
• Manufacturer: KAMOKA

• Switch Pressure [bar]: 0.3
• Thread Size: 1/8x28 BSPT
• Sensor Type: Closed-type Sensor
• Name: OLISURVELšLITUS
• Manufacturer: VER

• Spanner Size: 13
• Material: Brass
• Number of pins: 1
• Thread Size: 1/8" - 28
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX

• Thread Size: 1/8x28 BSP
• Pressure [bar]: 0.35
• Manufacturer: FAE

• Fabrication Number: ECT-MS-000
• Name: NTY ECT-MS-000
• Manufacturer: NTY

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Number of pins: 1
• Spanner Size: 12
• Thread Size: 1/8
• for OE number: 4671065
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• for OE number: MD 091056
• Number of pins: 1
• Weight [kg]: 0.02
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Pressure [bar]: 0.3
• Housing Colour: black
• Thread Size: 1/8
• Spanner Size: 24
• Number of pins: 1
• Name: OLISURVELšLITUS
• Manufacturer: DLP
• Quality class: PJ

Additional information: "Tootja: DELPHI
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
(kvaliteediklass: PJ)"

• Engine Code: 4G93 (GDI)
• Pressure [bar]: 0
• Thread Size: 1/8 GAS
• Spanner Size: 24
• Name: OLISURVELšLITUS
• Manufacturer: EPS

• External Thread Size: 1/8" - 28
• Spanner Size: 13
• Number of connectors: 1
• Material: Brass
• Weight [kg]: 0.01
• Manufacturer: SWAG
• Name: SW 81 92 8265

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• External Thread Size: 1/8" - 28
• Spanner Size: 13
• Number of connectors: 1
• Material: Brass
• Weight [kg]: 0.01
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thread Size: 3/8x19 BSP
• Manufacturer: VERNET

• Thread Size: 1/8 GAS
• Spanner Size: 13
• Number of pins: 1
• Manufacturer: ERA

• Engine Code: 4G93 (GDI)
• Thread Size: 1/8 GAS
• Spanner Size: 13
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Mounting Type: Bolted
• Voltage [V]: 12
• Pressure [bar]: 0.4
• Combi Switch Function: Normally Closed Contact
• Thread Size: 1/8 GAS
• Colour: red
• Spanner Size: 24
• Number of pins: 1
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6ZF007392001

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: rectangular
• Number of pins: 2
• Socket colour: black
• Spanner Size: 19
• Thread Size: 3/8
• for OE number: MD177572
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Thread Size: 1/8x28 BSPT
• Manufacturer: VERNET

• Connector Shape: oval
• Material: Plastic
• Number of pins: 2
• Plug Type: Female
• Sensor Type: NTC Sensor
• Spanner Size: S19
• Thread Size: PT3/8
• Name: NI 207007
• Manufacturer: NISSENS

Technical Information: FIRST FIT - a time-saving installation! Find all additional parts such as O-rings, clip, washer in the box.

• Thread Size: 3/8 x 19 BSP
• Colour: black
• Spanner Size: 19
• Number of pins: 2
• Weight [kg]: 0.042
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 3
• Supplementary Article/Info 2: without cable
• Connector Shape: oval
• Fabrication Number: ECP-MS-004
• Manufacturer: NTY

• Colour: black
• Number of pins: 2
• Weight [kg]: 0.3
• Packaging length [cm]: 12
• Packaging width [cm]: 8
• Packaging height [cm]: 6

• Housing Colour: black
• Number of pins: 2
• Thread Size: PT3/8
• Spanner Size: 19
• Manufacturer: DELPHI
• Name: DE TS10327

• Number of connectors: 2
• Colour: black
• Weight [kg]: 0.066
• Manufacturer: BLUE PRINT

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Length [mm]: 59.7
• Spanner Size: 19
• Number of connectors: 2
• Colour: black
• Weight [kg]: 0.04
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Length [mm]: 59.7
• Spanner Size: 19
• Number of connectors: 2
• Colour: black
• Weight [kg]: 0.04
• Name: SW 80 93 2375
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: 4G93 (GDI)
• Thread Size: 3/8-GAS
• Spanner Size: 19
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Voltage [V]: 12
• Resistor [Ohm]: 2,080, 294
• Temperature range from [°C]: 25
• Temperature range to [°C]: 80
• Thread Size: 3/8 GAS
• Colour: black
• Spanner Size: 19
• Sensor Type: NTC Sensor
• Number of pins: 2
• Corresponds to the original part in colour: black
• Mounting Type: Vertical Screw Fitting
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Alternatively:
• Number of pins: 3
• Alternative Repair Kit: 550346
• Fitting Depth [mm]: 11
• Manufacturer: ERA

Manufacturer: MAGNETI MARELLI

• Engine Code: 4G93 (GDI)
• Alternatively:
• Rotation Direction: Clockwise rotation
• Number of pins: 4
• Alternative Repair Kit: 550512
• Manufacturer: ERA

• Construction Year from: 06.2000
• Construction Year to: 08.2001
• Number of pins: 3
• Connector Shape: oval
• Supplementary Article/Info 2: without cable
• Manufacturer: MEAT&DORIA

• Lambda Sensor: Lambda Sensor, Thread pre-greased
• Fabrication Number: ESL-UV-001
• Manufacturer: NTY
• Name: NTY ESL-UV-001

• Lambda Sensor: Regulating Probe, Thread pre-greased
• Fabrication Number: ESL-MS-012
• Manufacturer: NTY

Fitting Position: Right Front, Left Front, before catalytic converter

• Construction Year from: 06.2000
• Construction Year to: 08.2001
• Voltage [V]: 12
• Supplementary Article/Supplementary Info: without cable pull
• Number of pins: 3
• Weight [kg]: 0.03
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: ESEN SKV

• Construction Year from: 06.2000
• Number of pins: 3

• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Number of pins: 3
• for OE number: MD355407

• Engine Code: 4G93 (GDI)
• Number of pins: 3
• Supplementary Article/Info 2: for camshaft, without cable
• Required quantity: 1
• Sensor Type: Hall Sensor
• Supplementary Article/Supplementary Info: with seal
• Number of connectors: 3
• Rated Voltage [V]: 12
• Fitting Depth [mm]: 27
• Housing Colour: black
• Connector Shape: oval
• Number of mounting bores: 1
• Weight [kg]: 0.02
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Lambda Sensor
• Weight [kg]: 0.12
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV121
• Manufacturer: ESEN SKV

• Engine Code: 4G93 (GDI)
• Cable Length [mm]: 350
• Alternatively:
• Number of pins: 2
• Fitting Depth [mm]: 12
• Alternative Repair Kit: 550334
• Manufacturer: ERA

• Construction Year to: 06.2000
• Lambda Sensor: Regulating Probe, Finger probe
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Transmission Type: Manual Transmission
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Construction Year to: 06.2000
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 103
• Gross Weight [g]: 147
• Manufacturer: DENSO
• Lisainfo: DOX-0109 DENSO
• Additional information: DOX-0109 DENSO

Lambda Sensor: Regulating Probe, Heated, Finger probe, Lambda Sensor

• Engine Code: 4G93-H
• Number of pins: 3
• Voltage [V]: 12
• Connector Shape: oval
• Supplementary Article/Info 2: without cable
• Weight [kg]: 0.03
• Name: ANDUR, VŽNTVOLL
• Manufacturer: VAL

• Housing Type: with housing
• Fabrication Number: EPP-MS-000
• Name: NTY EPP-MS-000
• Manufacturer: NTY

• Construction Year to: 06.2000
• Engine Code: 4G93 (DOHC)
• Fitting Position: before catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Lambda Sensor: Planar probe, Heated, Thread pre-greased
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Manufacturer: VEMO GERMANY

Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 07SKV191
• Manufacturer: ESEN SKV

• Construction Year to: 06.2000
• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Engine Code: 4G93 (GDI)
• Construction Year from: 09.2001
• Fitting Position: Front
• Block Separation:
• Lambda Sensor: Heated
• External Thread Size: M18 x 1,5
• Number of circuits: 4
• Number of connectors: 4
• Cable Length [mm]: 640
• Weight [kg]: 0.132
• Name: LAMBDA ANDUR
• Manufacturer: BLP

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

Manufacturer: ASHIKA

• Vehicle type: I.O
• Mounting Type: Flange mounting
• Number of bolts/screws: 4
• Number of pins: 7
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 8ET358095561

Brief Information: *** HELLA Electronics OE competence for over 60 years.