• for OE number: 4571477
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 1,640
• Number of pins: 4
• Weight [g]: 110
• Gross Weight [g]: 143
• Manufacturer: DENSO

Lambda Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
406 (8B), 10.95-05.0
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
406 (8B), 10.95-05.0
(kvaliteediklass: Q)"

• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Lambda Sensor: Diagnostic Probe
• Length [mm]: 1,500
• Fabrication Number: ESL-CT-018
• Manufacturer: NTY

• Cable Length [mm]: 1,235
• Lambda Sensor: Diagnostic Probe
• Number of circuits: 4
• Manufacturer: DELLO AUTOMEGA

• Construction Year to: 06.2004
• Lambda Sensor: Regulating Probe, Heated
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 1,220
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• for RPO number from: 08687
• Emission Standard: L3, D3, FL5/L5, US 83, US 94, L4
• Block Separation:
• for facelift:
• for RPO number up to: 08686
• Vehicle Equipment: for vehicles with self-diagnosis system
• Lambda Sensor: Regulating Probe, Planar probe
• Exhaust System: before catalytic converter
• Number of pins: 4
• Length [mm]: 610
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Engine Code: RFN (EW10J4)
• not for emission standard: Euro 3, Euro 4 (D4)
• Lambda Sensor: Regulating Probe, Heated
• Number of circuits: 4
• Length [mm]: 1,230
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Engine Code: RFN (EW10J4)
• Lambda Sensor: Regulating Probe
• Number of circuits: 4
• Supplementary Article/Info 2: without plug
• Manufacturer: ENERGY

• Fitting Position: before catalytic converter
• Lambda Sensor: Regulating Probe, Planar probe
• for RPO number from: 08687
• Emission Standard: L3, D3, FL5/L5, US 83, US 94, L4
• Block Separation:
• Vehicle Equipment: for vehicles with self-diagnosis system
• Number of pins: 4
• Length [mm]: 1,275
• Manufacturer: TOPRAN HANS PRIES

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Construction Year to: 06.2004
• Lambda Sensor: Regulating Probe, Diagnostic Probe, Heated
• Block Separation:
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: MAX
• Lisainfo: MGS-615
• Additional information: MGS-615

Fitting Position: before catalytic converter, after catalytic converter

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Line insulation design: with silicone-coated woven-fibre insulation
• Cable Length [mm]: 1,250
• Number of circuits: 4
• Version: ZR PLANAR
• Weight [kg]: 0.181
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Regulating Probe, Planar probe, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 525
• Name: LAMBDA ANDUR
• Manufacturer: DLP
• Quality class: PJ

Additional information: "Tootja: DELPHI
406 (8B), 10.95-05.0
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
406 (8B), 10.95-05.0
(kvaliteediklass: PJ)"

• Lambda Sensor: Lambda Sensor
• Cable Length [mm]: 1,320
• Number of circuits: 4
• Manufacturer: ERA

• Lambda Sensor: Regulating Probe, Planar probe, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 380
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Fitting Position: Front, after catalytic converter
• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Line insulation design: with silicone-coated woven-fibre insulation
• Weight [kg]: 0.187
• Socket colour: blue
• Connector Shape: rectangular
• Number of pins: 4
• Thread Size: M18 x 1,5
• for OE number: 1628 HV
• Cable Length [mm]: 1,320
• Length [mm]: 1,490
• Number of circuits: 4
• Version: ZR PLANAR
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• for OE number: 000 540 3917
• Cable Length [mm]: 750
• Number of pins: 4
• Lambda Sensor: Heated
• Manufacturer: TRUCKTEC AUTOMOTIVE

• Lambda Sensor: Regulating Probe
• Construction Year to: 06.2004
• Engine Code: EW10J4
• Voltage [V]: 12
• Length [mm]: 1,230
• Number of circuits: 4
• Weight [kg]: 0.11
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV037

• Lambda Sensor: Regulating Probe, Planar probe, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 530
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Fitting Position: before catalytic converter
• Lambda Sensor: Regulating Probe, Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 570
• Weight [kg]: 0.092
• for OE number: 1618.Z6
• Name: SW 33 10 3089
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Conductor Number: 4
• Resistor [Ohm]: 9
• Length [mm]: 1,520
• Number of circuits: 4
• Cable Length [mm]: 1,520
• Lambda Sensor: Heated
• Name: LAMBDA ANDUR
• Manufacturer: MAG

• Line insulation design: with silicone-coated woven-fibre insulation
• Connector Shape: round
• Conductor Number: 4
• Cable Length [mm]: 450
• Thread Size: M18 x 1,5
• Length [mm]: 570
• Version: ZR-PLANAR
• Weight [kg]: 0.143
• Lambda Sensor: Thread pre-greased
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• for RPO number from: 08687
• Fitting Position: before catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 1,300
• Number of connectors: 4
• Weight [kg]: 0.199
• Lambda Sensor: Thread pre-greased
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 06.2004
• Fitting Position: after catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Lambda Sensor: Planar probe, Heated, Thread pre-greased
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Manufacturer: VEMO GERMANY

Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 06.2004
• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 1,260
• Available as universal article as well, see article no.: 0258986615
• Recommended change interval [km]: 160,000
• Manufacturer: BOSCH
• Name: BS 0258006026

• Lambda Sensor: Regulating Probe
• Construction Year to: 06.2004
• Exhaust System: before catalytic converter
• Voltage [V]: 12
• Length [mm]: 1,260
• Number of circuits: 4
• Weight [kg]: 0.17
• Resistor [Ohm]: 9
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV711
• Manufacturer: ESEN SKV

• Lambda Sensor: Regulating Probe, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 470
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Name: Lambda andur
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Lambda Sensor: Planar probe
• Number of pins: 4
• Cable Length [mm]: 1,370
• Quality: OE EQUIVALENT
• Manufacturer: MEAT&DORIA

• Construction Year to: 06.2004
• Lambda Sensor: Regulating Probe, Diagnostic Probe
• Block Separation:
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

Fitting Position: before catalytic converter, after catalytic converter

• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 93
• Gross Weight [g]: 140
• Manufacturer: DENSO
• Name: DN DOX-0150
• Quality class: Q

Lambda Sensor: Regulating Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
(kvaliteediklass: Q)"

• Lambda Sensor: Regulating Probe, Planar probe, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 540
• Manufacturer: DELPHI
• Name: DE ES20258-12B1

• Construction Year to: 06.2004
• Lambda Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 1,510
• Available as universal article as well, see article no.: 0258986615
• Recommended change interval [km]: 160,000
• Manufacturer: BOSCH
• Name: BS 0258006029

• Construction Year to: 04.2004
• Lambda Sensor: Regulating Probe, Thread pre-greased
• Fitting Position: before catalytic converter
• Line insulation design: with thermal protection flexible insulating tubing
• Connector Shape: angular
• Thread Size: M18x1,5
• Length [mm]: 1,250
• Number of circuits: 4
• Weight [kg]: 0.19
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Regulating Probe, Planar probe, Heated
• Fitting Position: before catalytic converter
• Block Separation:
• Construction Year to: 05.2004
• Engine Code: RFN (EW10J4)
• Cable Length [mm]: 1
• Manufacturer: DELPHI
• Name: DE ES20309-12B1

• Exhaust System: for pre-catalytic converter
• for OE number: 8677894
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 1,250
• Number of pins: 4
• Weight [g]: 102
• Gross Weight [g]: 135
• Manufacturer: DENSO
• Name: DN DOX-2045
• Lisainfo: DOX-2045 DENSO
• Additional information: DOX-2045 DENSO

Lambda Sensor: Regulating Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor

• Fitting Position: after catalytic converter
• Cable Length [mm]: 1
• Lambda Sensor: Planar probe, Heated
• Manufacturer: DELPHI

• Engine Code: RFN (EW10J4)
• Fitting Position: after catalytic converter
• Length [mm]: 1,500
• Cable Length [mm]: 1,500
• Conductor Number: 4
• Available as universal article as well, see article no.: 1.998.240
• Number of circuits: 4
• Name: EP 1.998.301
• Manufacturer: EPS

Lambda Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased

• Lambda Sensor: Diagnostic Probe, Heated
• Fitting Position: after catalytic converter
• Number of pins: 4
• Length [mm]: 1,520
• Socket colour: blue
• Technical Information Number: Universal 77015
• Manufacturer: FAE

• Lambda Sensor: Diagnostic Probe, Planar probe
• Number of pins: 4
• Cable Length [mm]: 1,370
• for OE number: 9622997780
• Manufacturer: MEAT&DORIA