• Construction Year from: 08.2004
• Transmission Type: Manual Transmission
• Exhaust System: for pre-catalytic converter
• for OE number: MHK100840
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 620
• Number of pins: 4
• Weight [g]: 105
• Gross Weight [g]: 138
• Manufacturer: DENSO
• Name: DN DOX-2017

Lambda Sensor: Regulating Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
FREELANDER (LN), 02.
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
FREELANDER (LN), 02.
(kvaliteediklass: Q)"

• Transmission Type: Manual Transmission
• for OE number: MHK101086
• Quality: OE
• Manufacturer Restriction: DENSO
• Connector type: with rubber grommet
• Thread Size: M18x1.5
• Cable Length [mm]: 770
• Number of pins: 4
• Weight [g]: 116
• Gross Weight [g]: 149
• Manufacturer: DENSO

Lambda Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
25 (RF), 09.99-05.05
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
25 (RF), 09.99-05.05
(kvaliteediklass: Q)"

• Engine Code: 11 K4F
• Housing Colour: white
• Thread Size: M12x1,5
• Spanner Size: 22
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Engine Code: 11 K4F
• Housing Colour: brown
• Thread Size: M12x1,5
• Spanner Size: 19
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Number of pins: 2
• for OE number: MEK100060
• Weight [kg]: 0.033
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 2
• Housing Colour: brown
• Thread Size: M 12x1,5
• Manufacturer: FAE

• Number of pins: 2
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: DLP

• Fabrication Number: ECM-LR-000
• Manufacturer: NTY

• Lambda Sensor: Regulating Probe, Thread pre-greased
• Connector/Clamp: Connector may need adjustment
• Number of circuits: 4
• Fitting Position: before catalytic converter
• Fabrication Number: ESL-UV-000
• Manufacturer: NTY

• Number of pins: 4
• Connector Shape: oval
• Number of mounting bores: 2
• Supplementary Article/Info 2: with integrated air temperature sensor
• Pressure from [kPA]: 14
• Pressure to [kPA]: 104
• for OE number: 12 14 0 872 648, MHK100820
• Manufacturer: MEAT&DORIA

• Required quantity: 1
• Name: CZUJNIK CI—N. POWIETRZA
• Manufacturer: BRM

• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Vehicle Identification Number (VIN) from: YD471565
• Number of pins: 4
• Pressure from [kPA]: 15
• Name: ANDUR,OHUVOTU ROHK
• Manufacturer: DLP

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Number of pins: 3
• Connector Shape: oval
• Supplementary Article/Info 2: without cable
• Number of mounting bores: 1
• Sensor Type: Hall Sensor
• Fitting Depth [mm]: 28
• for OE number: NSC100932
• Manufacturer: MEAT&DORIA

• Alternatively:
• Number of pins: 4
• Alternative Repair Kit: 551396
• Manufacturer: ERA

• Fuel Type: Petrol
• Weight [kg]: 0.039
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Regulating Probe, Heated
• Vehicle Identification Number (VIN) to: YD471564
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Number of pins: 3
• Fitting Depth [mm]: 27.5
• Manufacturer: ERA

• Number of connectors: 4
• Colour: black
• Weight [kg]: 0.02
• Name: ANDUR,OHUVOTU ROHK
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: 11 K4F
• Pressure from [kPA]: 10
• Pressure to [kPA]: 118
• Output Voltage, from [V]: 0.31
• Output Voltage, up to [V]: 4.75
• Name: ANDUR,OHUVOTU ROHK
• Manufacturer: EPS

• Lambda Sensor: Regulating Probe, Diagnostic Probe, Heated
• Vehicle Identification Number (VIN) from: YD471565
• Block Separation:
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: MAX
• Lisainfo: MGS-615
• Additional information: MGS-615

Fitting Position: before catalytic converter, after catalytic converter

Manufacturer: MAGNETI MARELLI

• Lambda Sensor: Lambda Sensor
• Length [mm]: 972
• Number of circuits: 4
• Manufacturer: FAST

• Length [mm]: 568
• Conductor Number: 4
• Number of circuits: 4
• Resistor [Ohm]: 9
• Cable Length [mm]: 568
• Lambda Sensor: Heated
• Name: LAMBDA ANDUR
• Manufacturer: MAG

• Lambda Sensor: Lambda Sensor
• Voltage [V]: 12
• Length [mm]: 605
• Number of circuits: 4
• Weight [kg]: 0.13
• Resistor [Ohm]: 6
• Operating Mode: Electric
• Warranty: 3 years warranty
• Name: CE 09SKV578
• Manufacturer: ESEN SKV

• Lambda Sensor: Regulating Probe, Lambda Sensor
• Exhaust System: before catalytic converter
• Voltage [V]: 12
• Length [mm]: 568
• Number of circuits: 4
• Weight [kg]: 0.14
• Resistor [Ohm]: 9
• Operating Mode: Electric
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY
• Name: CE 09SKV730

• Lambda Sensor: Regulating Probe, Planar probe, Heated
• Fitting Position: before catalytic converter
• Vehicle Identification Number (VIN) to: 471564
• Cable Length [mm]: 605
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Lambda Sensor: Regulating Probe, Planar probe, Heated
• Fitting Position: before catalytic converter
• Vehicle Identification Number (VIN) from: 471565
• Cable Length [mm]: 540
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Number of mounting bores: 2
• Pressure [Pa] from: 10,000
• Pressure [Pa] to: 117,000
• Voltage from [V]: 0.3
• Voltage to [V]: 4.65
• Number of pins: 4
• Manufacturer: METZGER

• Engine Code: 11 K4F
• Line insulation design: with silicone-coated woven-fibre insulation
• Number of pins: 4
• for OE number: V99760001
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Length [mm]: 350
• Exhaust System: after catalytic converter
• Manufacturer: VEMO GERMANY

Lambda Sensor: Regulating Probe, Finger probe, Heated, Thread pre-greased Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Regulating Probe, Diagnostic Probe
• Vehicle Identification Number (VIN) from: YD 471565
• Block Separation:
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

Fitting Position: before catalytic converter, after catalytic converter

• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Vehicle Identification Number (VIN) to: YD 471564
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Construction Year from: 08.2004
• Transmission Type: Manual Transmission
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 93
• Gross Weight [g]: 140
• Manufacturer: DENSO
• Name: DN DOX-0150
• Quality class: Q

Lambda Sensor: Regulating Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
(kvaliteediklass: Q)"

• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Vehicle Identification Number (VIN) to: YD 471564
• Number of circuits: 4
• Overall Length [mm]: 623
• Available as universal article as well, see article no.: 0258986506
• Recommended change interval [km]: 100,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Lambda Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 773
• Available as universal article as well, see article no.: 0258986615
• Recommended change interval [km]: 160,000
• Manufacturer: BOSCH

• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Vehicle Identification Number (VIN) from: YD 471565
• Number of circuits: 4
• Overall Length [mm]: 568
• Available as universal article as well, see article no.: 0258986615
• Recommended change interval [km]: 160,000
• Manufacturer: BOSCH

• Version: AM
• Number of pins: 3
• Rotation Direction: Anticlockwise rotation
• Manufacturer: METZGER