Tootekategooriad
Filtrid Pidurid vedrustus/alusvanker Roolisüsteem Jahutus/kliima Elektrisüsteem Veokonks/lisad Jõuülekanne Väljalaskesüsteem Kere Süüte-/eelsüütesüsteem Mootor Klaasid/klaasipuhastus Valgustus Kütus Kabiinivarustus HooldusToode
Kirjeldus
Laoseis
Hind
(km-ga)
- Fitting Position: Front and Rear
- Length [mm]: 48
-
External Thread [mm]: M14 x 1,
5 - Thread Length [mm]: 27
- Spanner Size: 17
- Lisainfo: PAKENDIS 20 tk
- Kogus pakendis: 20
- Length [mm]: 48
- Weight [kg]: 0.065
-
Thread Size: M 14 x 1,
5 mm -
External Thread [mm]: M14x1,
5 - Spanner Size: 17
- Outer Diameter [mm]: 48
- Bolt Head-/Nut Design: Male Hex
-
Quality/ Grade: 8,
8 -
Wheel Fastening: Ball seat A/
G - Thread Length [mm]: 27
- Voltage division in 2 channel mode [mV]: 48
- Tootja: VAICO
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
-
Rims: for light alloy rims,
for steel rims - Length [mm]: 48
- Outer Diameter [mm]: 23
-
External Thread Size: M14 x 1,
5 - Thread Length [mm]: 27
- Quality/ Grade: 8.8
- Spanner Size: 17
- Bolt Head-/Nut Design: Male Hex
-
Wheel Fastening: Ball seat A/
G - Colour: silver
- Material: Steel
-
Surface: Zinc-
coated - Screw length below head [mm]: 27
-
Fitting Position: Front Axle,
Rear Axle - Weight [kg]: 0.062
- Observe service information:
- Tootja: FEBI BILSTEIN
General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.
- Weight [kg]: 0.23
- Packaging length [cm]: 2.5
- Packaging width [cm]: 2.5
- Packaging height [cm]: 1.6
- Tootja: FEBEST
- Height [mm]: 18
- Spanner Size: 17
- Colour: grey
- Weight [kg]: 0.15
- Supplementary Article/Supplementary Info: with puller
- Tootja: FEBI
General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.
- Height [mm]: 18
- Spanner Size: 17
- Colour: black
- Weight [kg]: 0.15
- Supplementary Article/Supplementary Info: with puller
- Tootja: FEBI
General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.
- Length [mm]: 48
- Weight [kg]: 1.4
-
Thread Size: M 14 x 1,
5 mm -
External Thread [mm]: M14x1,
5 - Spanner Size: 17
- Outer Diameter [mm]: 48
- Bolt Head-/Nut Design: Male Hex
-
Quality/ Grade: 8,
8 -
Wheel Fastening: Ball seat A/
G - Thread Length [mm]: 27
- Quantity: 20
- Tootja: VAICO
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
Laki Auto universaaltooted
TecDoc sõidukite kataloog
TecDoc veokite kataloog