Tootekategooriad
Filter Pidurid Šassii Roolimine Jahutus/kliima Elektrisüsteem Jõuülekanne Väljalaskesüsteem Kere Süüte-/eelsüütesüsteem Mootor Klaasid/klaasipuhastus Valgustus Kütusesüsteemi seadmed Kabiinivarustus HooldusToode
Kirjeldus
Laoseis
Hind
(km-ga)
- DOT specification: DOT 4
- Chemical Properties: Synthetic
- Capacity [litre]: 1
- Dry Boiling Point [°C]: 245
- Packing Type: Bottle
- Nimetus: PIDURIVEDELIK
- Tootja: MAX
-
Lisainfo: 36-
0048
- DOT specification: DOT 4
- Chemical Properties: Synthetic
- Capacity [litre]: 3
- Dry Boiling Point [°C]: 245
- Packing Type: Canister
- Nimetus: PIDURIVEDELIK
- Tootja: MAX
-
Lisainfo: 36-
0049
3 Liitrit
- DOT specification: DOT 4
- Chemical Properties: Synthetic
- Capacity [litre]: 0.5
- Dry Boiling Point [°C]: 245
- Packing Type: Bottle
- Nimetus: PIDURIVEDELIK
- Tootja: MAX
- DOT specification: DOT 4
- Chemical Properties: Synthetic
- Capacity [litre]: 0.5
- Dry Boiling Point [°C]: 245
- Packing Type: Bottle
- Weight [kg]: 0.59
- Nimetus: PIDURIVEDELIK
- Tootja: VAL
- Ehitusaasta alates: 01.1984
- DOT specification: DOT 4
- Dry Boiling Point [°C]: 260
- Wet Boiling Point [°C]: 180
- Chemical Properties: Synthetic
- Recommended change interval [years]: 2
- Packing Type: Bottle
- Capacity [litre]: 0.25
- Observe system fill quantity:
- Observe the vehicle manufacturer specifications:
- Weight [kg]: 0.28
- Height [mm]: 50
- Width [mm]: 45
- Length [mm]: 70
-
Recommended change interval [km]: 40,
000 - Tootja: VAICO
Specification: FMVSS 116 DOT 4, SAE J 1703 / J 1704, FMVSS 116 DOT 3, ISO 4925 Class 4 General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- DOT specification: DOT 4
- Chemical Properties: Synthetic
- Capacity [litre]: 1
- Dry Boiling Point [°C]: 245
- Packing Type: Bottle
- Weight [kg]: 1.15
- Tootja: VALEO
- Nimetus: VA 402403
- Lisainfo: 402403 VAL
- Ehitusaasta alates: 01.1984
- Wet Boiling Point [°C]: 155
- DOT specification: DOT 4
- Dry Boiling Point [°C]: 260
- Chemical Properties: Synthetic
- Capacity [litre]: 0.5
- Recommended change interval [years]: 2
- Observe system fill quantity:
- Observe the vehicle manufacturer specifications:
- Height [mm]: 174
- Packing Type: Bottle
-
DIN/ISO: ISO 4925 Class 4,
ISO 4925 - Width [mm]: 58
-
Weight [kg]: 0.6,
0.858 -
Specification: FMVSS 116 DOT 4,
SAE J 1703 F - Length [mm]: 95
-
Recommended change interval [km]: 40,
000 - Tootja: VAICO
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- DOT specification: DOT 4+
- Chemical Properties: Synthetic
- Capacity [litre]: 1
- Dry Boiling Point [°C]: 265
- Packing Type: Bottle
- Weight [kg]: 1.13
- Tootja: VALEO
- Nimetus: VA 402406
- Ehitusaasta alates: 01.1984
- Dry Boiling Point [°C]: 260
- DOT specification: DOT 4
- Wet Boiling Point [°C]: 180
- Chemical Properties: Synthetic
- Recommended change interval [years]: 2
- Capacity [litre]: 1
- Observe the vehicle manufacturer specifications:
- Observe system fill quantity:
- Packing Type: Bottle
-
Recommended change interval [km]: 40,
000 - Length [mm]: 60
-
Weight [kg]: 1.15,
1.4 - Height [mm]: 225
- Width [mm]: 115
- Tootja: VAICO
Specification: FMVSS 116 DOT 4, ISO 4925 Class 4, FMVSS 116 DOT 3, SAE J 1703 / J 1704 General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Ehitusaasta alates: 01.1984
- Dry Boiling Point [°C]: 260
- Wet Boiling Point [°C]: 155
- DOT specification: DOT 4
- Chemical Properties: Synthetic
- Recommended change interval [years]: 2
- Capacity [litre]: 1
- Observe system fill quantity:
- Observe the vehicle manufacturer specifications:
-
Specification: SAE J 1703 F,
FMVSS 116 DOT 4 - Width [mm]: 115
-
Weight [kg]: 1.15,
1.4 - Length [mm]: 60
- Packing Type: Bottle
- DIN/ISO: ISO 4925
-
Recommended change interval [km]: 40,
000 - Height [mm]: 225
- Tootja: VAICO
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- DOT specification: DOT 4
- Chemical Properties: Synthetic
- Capacity [litre]: 5
- Dry Boiling Point [°C]: 245
- Packing Type: Canister
- Weight [kg]: 0.55
- Tootja: VALEO
- Nimetus: VA 402404
- Ehitusaasta alates: 01.1984
- Dry Boiling Point [°C]: 260
- Wet Boiling Point [°C]: 180
- DOT specification: DOT 4
- Chemical Properties: Synthetic
- Capacity [litre]: 5
- Recommended change interval [years]: 2
-
Recommended change interval [km]: 40,
000 - Observe the vehicle manufacturer specifications:
- Observe system fill quantity:
- Width [mm]: 115
- Length [mm]: 300
- Height [mm]: 230
- Weight [kg]: 4.72
- Packing Type: Canister
- Tootja: VAICO
Specification: ISO 4925 Class 4, FMVSS 116 DOT 4, SAE J 1703 / J 1704, FMVSS 116 DOT 3 General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Ehitusaasta alates: 01.1984
- Wet Boiling Point [°C]: 155
- DOT specification: DOT 4
- Dry Boiling Point [°C]: 260
- Chemical Properties: Synthetic
- Capacity [litre]: 5
- Recommended change interval [years]: 2
- Observe the vehicle manufacturer specifications:
- Observe system fill quantity:
-
Specification: SAE J 1703 F,
FMVSS 116 DOT 4 - Height [mm]: 230
- Packing Type: Canister
- Length [mm]: 300
- DIN/ISO: ISO 4925
- Width [mm]: 115
- Weight [kg]: 4.72
-
Recommended change interval [km]: 40,
000 - Tootja: VAICO
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
Laki Auto universaaltooted
TecDoc sõidukite kataloog
TecDoc veokite kataloog