• Installatsiooni pool: sees, silla taga, esisild vasakul, all
• Control/Trailing Arm Type: Control Arm
• Mounting Type: Rubber-Metal Mount
• Lisainfo: MITSUBISHI, VOLVO

• Fitting Position: outer, Front Axle Right
• Axle alignment required after fitting:
• paired article number: V95-0140
• Weight [kg]: 0.222
• Tootja: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fabrication Number: ZTT-MS-007A
• Tootja: NTY

Fitting Position: Rear Axle, inner, outer, Left, Right, Lower, Rear, behind the axle, Centre

• Material: Rubber/Metal
• Thickness [mm]: 106
• Outer Diameter [mm]: 36
• Tootja: MERTZ

Fitting Position: Rear Axle Left, Rear Axle Right, Upper, Front, outer, inner

• Fitting Position: Rear Axle, inner, outer, Left, Right, Lower, Rear
• Fabrication Number: ZTT-MS-000C
• Tootja: NTY

• Fitting Position: Front, Lower Front Axle
• Fabrication Number: ZTP-MS-006A

• Fitting Position: Rear Axle
• Control/Trailing Arm Type: for control arm
• Fabrication Number: ZTT-MS-000B
• Tootja: NTY

• for OE number: 30 818 467
• Fitting Position: Lower Front Axle, Lower
• Tootja: GSP

• Installatsiooni pool: all, esisild vasakul, esisild paremal
• Kõrgus (mm): 60
• Siseläbimõõt [mm]: 12
• Välisläbimõõt [mm]: 37
• Roolimisliik: Õõtshoob
• Laagritüüp: Kummi-metalllaager
• Nimetus: Control arm bush left=right
• Kvaliteediklass: PJ

Lisainfo: "Tootja: SRL
VOLVO S/V40
(kvaliteediklass: PJ)"

• for OE number: MR102012
• Fitting Position: Rear Axle Left, Lower, outer, Rear Axle Right
• Tootja: GSP

• Fitting Position: outer, Rear Axle Lower
• Control/Trailing Arm Type: for semi-trailing arm
• Fabrication Number: ZTT-MS-000A
• Tootja: NTY

• Fitting Position: Rear Axle Lower
• Fabrication Number: ZTT-MS-007B

• Fitting Position: Front Axle, inner, behind the axle, Left, Lower
• Fabrication Number: ZTP-MS-006B
• paired article number: ZTP-MS-006C

• Fitting Position: Front Axle, inner, behind the axle, Right, Lower
• Fabrication Number: ZTP-MS-006C
• paired article number: ZTP-MS-006B

• Fitting Position: Rear Axle, outer, inner
• Control/Trailing Arm Type: for semi-trailing arm
• Fabrication Number: ZTT-CH-006A
• Tootja: NTY

• Installatsiooni pool: Tagasild vasakul, Tagasild paremal, üleval
• Tootja: GSP

• Control/Trailing Arm Type: for control arm
• Fitting Position: inner, outer, Rear Axle, Upper, Front
• Nimetus: Puks - K„„ndmik MITSUBISHI T. COLT/LANCER/CARISMA
• Tootja: MAX

• Fitting Position: inner, Front Axle
• Required quantity: 2
• Material: Rubber/Metal
• Weight [g]: 144
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 36
• Length [mm]: 60
• Nimetus: IM 32503
• Tootja: ORIGINAL IMPERIUM

• Control/Trailing Arm Type: for control arm
• Fitting Position: Rear Axle, Lower, Front
• Mounting Type: Rubber-Metal Mount
• Thickness [mm]: 50
• Outer Diameter [mm]: 36
• Inner Diameter [mm]: 13
• Tootja: MAX

Nimetus: Puks - K„„ndmik MITSUBISHI T. COLT/ LANCER/ CARISMA

• Length [mm]: 60
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 37
• Fitting Position: Front Axle both sides, Front
• Tootja: ASHIKA

• Control/Trailing Arm Type: for control arm
• Fitting Position: both sides, Rear Axle, Lower, Rear
• Inner Diameter [mm]: 12
• Required quantity: 4
• Nimetus: Puks - K„„ndmik VOLVO T. V40 WEW.
• Tootja: TED

• Outer Diameter [mm]: 36
• Fitting Position: Upper, Front, inner, outer, Rear Axle
• Control/Trailing Arm Type: for control arm
• Required quantity: 2
• Nimetus: Puks - K„„ndmik VOLVO T. V40
• Tootja: TED

• Fitting Position: Rear Axle, Left, Right
• Weight [g]: 143
• Tootja: IMPERGOM

• Fitting Position: Rear Axle, Left, Right, Front
• Weight [g]: 380
• Nimetus: IM 1570
• Tootja: ORIGINAL IMPERIUM

• Fitting Position: Rear Axle, both sides
• Height [mm]: 49.5
• Inner Diameter [mm]: 12
• Control/Trailing Arm Type: for control arm
• Mounting Type: Rubber-Metal Mount
• Outer Diameter 1 [mm]: 36
• Outer Diameter 2 [mm]: 35
• Tootja: OPTIMAL ZAWIESZENIE

• tootmise kuupäev kuni: 200306
• Fitting Position: inner, Rear Axle Lower
• Weight [kg]: 0.15
• Outer Diameter [mm]: 36
• Packaging length [cm]: 4.5
• Packaging width [cm]: 3.7
• Packaging height [cm]: 3.7
• Tootja: FEBEST

• for OE number: 4113A041
• Fitting Position: Rear Axle Left, Rear Axle Right, Lower
• Tootja: GSP

• for OE number: 30 620 785
• Fitting Position: Rear Axle, Lower
• Tootja: GSP

• Käigukasti liik: Käigukast, Automaatkäigukast
• tootmise kuupäev kuni: 200205
• Fitting Position: outer, Rear Axle Lower
• Nimetus: Puks
• Tootja: MAX

OE-numbri jaoks: MR491346, MR491348, MR130480, MW30620785, MR491345, MB809222, MB809220, MR491347, MR915104, MR130479, MR915105, MW30620786, MB809223

• Installatsiooni pool: all, ees, Tagasild vasakul, Tagasild paremal
• Jämedus/Tugevus (mm): 50
• Siseläbimõõt [mm]: 13
• Välisläbimõõt [mm]: 36
• Roolimisliik: Õõtshoob
• Laagritüüp: Kummi-metalllaager
• Nimetus: Control arm bush left=right
• Kvaliteediklass: PJ

Lisainfo: "Tootja: SRL
MITSUB. GALANT, 93-
(kvaliteediklass: PJ)"

• Tootmise kuupäev alates: 200105
• tootmise kuupäev kuni: 200306
• Fitting Position: Rear, inner
• Length [mm]: 79
• Weight [kg]: 0.185
• Quantity: 2
• Packaging length [cm]: 9.1
• Packaging width [cm]: 2.4
• Packaging height [cm]: 2.4
• Tootja: FEBEST

• Fabrication Number: ZTT-MS-000D
• Tootja: NTY

Fitting Position: Rear Axle, outer, in front of axle, Left, Right, Lower

• Installatsiooni pool: Tagasild mõlemapoolselt
• Siseläbimõõt [mm]: 12
• Välisläbimõõt [mm]: 36
• Kõrgus (mm): 45
• Nimetus: ALT 91659AL
• Tootja: ALTE AUTOMOTIVE

• tootmise kuupäev kuni: 200306
• Fitting Position: Lower Front Axle, Front
• Weight [kg]: 0.149
• Packaging length [cm]: 6
• Packaging width [cm]: 4
• Packaging height [cm]: 4
• Tootja: FEBEST

• Width [mm]: 53
• Inner Diameter [mm]: 21
• Outer Diameter [mm]: 64
• Fitting Position: Front Axle Left, Rear
• Nimetus: Puks - K„„ndmik MITSUBISHI P.
• Tootja: JPA

• Width [mm]: 53
• Inner Diameter [mm]: 21
• Outer Diameter [mm]: 64
• Fitting Position: Front Axle Right, Rear
• Nimetus: Puks - K„„ndmik MITSUBISHI P.
• Tootja: JPA

• Control/Trailing Arm Type: for control arm
• Fitting Position: inner, outer, Rear Axle, Upper, Front
• Required quantity: 2
• Nimetus: Puks - K„„ndmik MITSUBISHI T. COLT/LANCER/CARISMA
• Tootja: TED

• Width [mm]: 53
• Inner Diameter [mm]: 21
• Outer Diameter [mm]: 64
• Fitting Position: Front Axle Right, Rear
• Tootja: ASHIKA

• Laius (mm): 53
• Siseläbimõõt [mm]: 21
• Välisläbimõõt [mm]: 64
• Installatsiooni pool: esisild paremal, taga
• Tootja: JAPKO

• Fitting Position: Front Axle, Lower, Rear, Right
• Required quantity: 1
• paired article number: 00441663
• Nimetus: Puks - K„„ndmik MITSUBISHI P.
• Tootja: TED

• Laius (mm): 53
• Siseläbimõõt [mm]: 21
• Välisläbimõõt [mm]: 64
• Installatsiooni pool: esisild vasakul, taga
• Tootja: JAPKO

• Fitting Position: Lower, Front Axle Right
• paired article number: 511844
• Tootja: GSP

• Control/Trailing Arm Type: for control arm
• Mounting Type: Rubber-Metal Mount
• Fitting Position: Rear Axle, Lower
• Axle alignment required after fitting:
• Weight [kg]: 0.151
• Tootja: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Rear Axle, Front
• Mounting Type: Rubber-Metal Mount

• tootmise kuupäev kuni: 200306
• Fitting Position: Rear Axle Lower
• Weight [kg]: 0.228
• Outer Diameter [mm]: 36
• Packaging length [cm]: 10.7
• Packaging width [cm]: 3.6
• Packaging height [cm]: 3.6
• Tootja: FEBEST

OE-numbri jaoks: MB809220, MB809221, MB809222, MB809223, MR130479, MR130480, MR491345, MR491346, MR491347, MR491348, MR915104, MR915105, MW30620785, MW30620786

• tootmise kuupäev kuni: 200306
• Fitting Position: Lower Front Axle, Left
• Weight [kg]: 0.307
• Packaging length [cm]: 9
• Packaging width [cm]: 8
• Packaging height [cm]: 5.5
• Tootja: FEBEST

• tootmise kuupäev kuni: 200306
• Fitting Position: Lower Front Axle, Right
• Weight [kg]: 0.301
• Packaging length [cm]: 8.2
• Packaging width [cm]: 7.5
• Packaging height [cm]: 5.7
• Tootja: FEBEST

• Fitting Position: Front Axle, Lower, Rear, Left
• Required quantity: 1
• paired article number: 00441664
• Nimetus: Puks - K„„ndmik MITSUBISHI P.
• Tootja: TED

• Fitting Position: Rear Axle, Front
• Mounting Type: Rubber-Metal Mount
• Thickness [mm]: 75
• Outer Diameter [mm]: 70
• Inner Diameter [mm]: 12
• Nimetus: Laagripuks, ootshoob
• Tootja: MAX

• Thickness [mm]: 50
• Inner Diameter [mm]: 13
• Outer Diameter [mm]: 36
• Control/Trailing Arm Type: for control arm
• Fitting Position: Rear Axle Left, Lower, Front, Rear Axle Right
• Mounting Type: Rubber-Metal Mount
• Weight [kg]: 0.15
• Nimetus: Puks - K„„ndmik MITSUBISHI T. COLT/LANCER/CARISMA
• Tootja: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Installatsiooni pool: Tagasild, väljas, silla ees, all
• Inner Diameter 1 [mm]: 12
• Outer Diameter 1 [mm]: 77
• Thickness 1 [mm]: 75
• Tootja: DELPHI
• Nimetus: DE TD1075W

• Thickness [mm]: 50
• Inner Diameter [mm]: 13
• Outer Diameter [mm]: 36
• Control/Trailing Arm Type: for control arm
• Fitting Position: Rear Axle Left, Lower, Front, Rear Axle Right
• Mounting Type: Rubber-Metal Mount
• Weight [kg]: 0.15
• Nimetus: Puks - K„„ndmik MITSUBISHI T. COLT/LANCER/CARISMA
• Tootja: BLP

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• tootmise kuupäev kuni: 200205
• Fitting Position: outer, inner, Rear Axle
• Weight [kg]: 0.171
• Packaging length [cm]: 5
• Packaging width [cm]: 3.6
• Packaging height [cm]: 3.6
• Tootja: FEBEST

• Thickness [mm]: 50
• Inner Diameter [mm]: 13
• Outer Diameter [mm]: 36
• Control/Trailing Arm Type: for control arm
• Fitting Position: Rear Axle Left, Lower, Front, Rear Axle Right
• Mounting Type: Rubber-Metal Mount
• Weight [kg]: 0.15
• Tootja: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thickness [mm]: 75
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 70
• Fitting Position: Rear Axle Left, Front, Rear Axle Right
• Mounting Type: Rubber-Metal Mount
• Weight [kg]: 0.5
• Tootja: BLP

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. Nimetus: Puks - K„„ndmik VOLVO T. S40/V40 /CARISMA/COLT/SPACE STAR DO 02/2002

• Installatsiooni pool: taga, esisild paremal
• Siseläbimõõt [mm]: 21
• Roolimisliik: Õõtshoob
• Laagritüüp: Kummi-metalllaager
• Kvaliteediklass: PJ
• Nimetus: Control arm bush right

• Installatsiooni pool: taga, esisild vasakul
• Siseläbimõõt [mm]: 21
• Roolimisliik: Õõtshoob
• Laagritüüp: Kummi-metalllaager
• Kvaliteediklass: PJ
• Nimetus: Control arm bush left

• Laagritüüp: Kummi-metalllaager
• Installatsiooni pool: Pealis
• Nimetus: Control arm bush left
• Kvaliteediklass: PJ

Lisainfo: "Tootja: TEKNOROT
VOLVO S/V40
(kvaliteediklass: PJ)"

• Installatsiooni pool: Tagasild mõlemapoolselt, ees
• vajaminev tükihulk: 2
• paired article number: VKDS 436004
• Height [mm]: 75
• Inner Diameter [mm]: 12.2
• Outer Diameter [mm]: 77.2
• Nimetus: SK VKDS436004
• Tootja: SKF

• tootmise kuupäev kuni: 200306
• Fitting Position: Rear Axle Lower
• Weight [kg]: 0.365
• Packaging length [cm]: 11.5
• Packaging width [cm]: 8
• Packaging height [cm]: 4.5
• Tootja: FEBEST

OE-numbri jaoks: MB809220, MB809221, MB809222, MB809223, MR130479, MR130480, MR491345, MR491346, MR491347, MR491348, MR915104, MR915105, MW30620785, MW30620786

• Thickness [mm]: 75
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 70
• Fitting Position: Rear Axle Left, Front, Rear Axle Right
• Mounting Type: Rubber-Metal Mount
• Weight [kg]: 0.5
• Tootja: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. Nimetus: Puks - K„„ndmik VOLVO T. S40/V40 /CARISMA/COLT/SPACE STAR PO 02/2002

• Installatsiooni pool: Tagasild mõlemapoolselt
• Välisläbimõõt [mm]: 36
• Kõrgus (mm): 106
• Nimetus: ALT 91658AL
• Tootja: ALTE AUTOMOTIVE

• Thickness [mm]: 75
• Inner Diameter [mm]: 12.3
• Outer Diameter [mm]: 70
• Fitting Position: Rear Axle Left, Front, Rear Axle Right
• Mounting Type: Rubber-Metal Mount
• Weight [kg]: 0.458
• Tootja: SWAG
• Nimetus: SW 80 94 1112

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Laagritüüp: Kummi-metalllaager
• Installatsiooni pool: Pealis
• Nimetus: Control arm bush right
• Kvaliteediklass: PJ

Lisainfo: "Tootja: TEKNOROT
VOLVO S/V40
(kvaliteediklass: PJ)"

• Fitting Position: Right, Front Axle
• Weight [g]: 403
• Nimetus: IM 7039
• Tootja: ORIGINAL IMPERIUM

• Installatsiooni pool: Tagasild, all, ees
• Siseläbimõõt [mm]: 13
• Välisläbimõõt [mm]: 40
• Kõrgus (mm): 45
• Nimetus: ALT 91672AL
• Tootja: ALTE AUTOMOTIVE

• Installatsiooni pool: Tagasild vasakul, Tagasild paremal
• Jämedus/Tugevus (mm): 75
• Siseläbimõõt [mm]: 12
• Välisläbimõõt [mm]: 70
• Roolimisliik: Längslenker
• Laagritüüp: Kummi-metalllaager
• Nimetus: Control arm bush left=right
• Kvaliteediklass: PJ

Lisainfo: "Tootja: SRL
M. COLT/LANCER, 92-
(kvaliteediklass: PJ)"

• Installatsiooni pool: esisild paremal, sees, silla taga, all
• paired article number: TD388W
• Tootja: DELPHI
• Nimetus: DE TD389W

• Installatsiooni pool: esisild vasakul, sees, silla taga, all
• paired article number: TD389W
• Tootja: DELPHI
• Nimetus: DE TD388W

• Outer Diameter [mm]: 36
• Material: Rubber/Metal
• Outer Length [mm]: 106
• Fitting Position: Rear Axle Left, Rear Axle Right
• Hole Spacing [mm]: 83.5
• Weight [kg]: 0.237
• Nimetus: Puks - K„„ndmik MITUBISHI T. COLT
• Tootja: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Installatsiooni pool: Tagasild, ees
• Roolimisliik: für Längslenker
• Mounting Type: Rubber-Metal Mount
• Inner Diameter [mm]: 12.1
• Outer Diameter [mm]: 70.1
• Width [mm]: 75
• SVHC: No SVHC present!
• Tootja: FAG

• Outer Diameter [mm]: 36
• Material: Rubber/Metal
• Outer Length [mm]: 106
• Fitting Position: Rear Axle Left, Rear Axle Right
• Hole Spacing [mm]: 83.5
• Weight [kg]: 0.22
• Tootja: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.