• Operating voltage [V]: 12
• Rated Power [W]: 480
• Rated current [A]: 40
• Combi Switch Function: Normally Open Contact
• Number of pins: 4
• Manufacturer: JP GROUP
• Lisainfo: Relay, 12 Volt, 40 Amp
• Additional information: Relay, 12 Volt, 40 Amp

Relay function: Terminal 75, Interior Blower, Suction pipe pre-heating, Sunroof, Pump, fuel pre-supply, Start-stop system, Magnetic clutch, Surge protection, Battery main switch, Engine control unit, Normally open contact, X contact relief, Fan, engine cooling, Electric booster heater, Secondary Air System, Water pump after-run, Rear window wiper, heater/air conditioning, Clamp 15, Fuel Pump, Window Regulator, Heated windscreen, Heated rear window, Parking Heater

• Operating voltage [V]: 12
• Number of connectors: 3

Lisainfo: Relay for turn signal and emergency light, 12 Volt, 4x21 W Additional information: Relay for turn signal and emergency light, 12 Volt, 4x21 W

• Number of connectors: 4
• Manufacturer: JP GROUP

Lisainfo: Relay for fuel pump and intake manifold heating, 12 Volt, 40 Amp Additional information: Relay for fuel pump and intake manifold heating, 12 Volt, 40 Amp

• Operating voltage [V]: 12
• Rated Power [W]: 120
• Rated current [A]: 10
• Combi Switch Function: Normally Open Contact
• Length [mm]: 30
• Width [mm]: 30
• Height [mm]: 42
• Connector type: 1x 2,8 mm, 5x 6,3 mm
• Number of pins: 6
• Manufacturer: JP GROUP
• Lisainfo: Relay for wiper/washer
• Additional information: Relay for wiper/washer

• Operating voltage [V]: 12
• Rated Power [W]: 2x21; 5
• Rated current [A]: 2
• Combi Switch Function: Normally Open Contact
• Length [mm]: 30
• Width [mm]: 30
• Height [mm]: 30
• Connector type: 3x 6,3 mm
• Vehicle Equipment: for vehicles without trailer hitch
• Number of pins: 3
• Name: OHUTULEDE RELEE
• Manufacturer: MAX
• Lisainfo: 103131DE5
• Additional information: 103131DE5

• Number of connectors: 4
• Rated Voltage [V]: 12
• Rated current [A]: 40
• Temperature range from [°C]: -40
• Temperature range to [°C]: 85
• General Information: relay
• Manufacturer: VIKA

• for relay slot number: 6
• Vehicle Identification Number (VIN) to: 6N-WW001001, 6N-WY000158
• Block Separation:
• Relay Number: 21
• Vehicle Identification Number (VIN) from: 6N-WW001002, 6N-WY000159
• Rated Voltage [V]: 12
• Rated Power [W]: 4 x 21
• Relay function: Indicator, Trailer indicator control
• Vehicle Equipment: for vehicles without trailer hitch
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Name: RELEE, KšTUSEPUMP
• Manufacturer: MAX

• Relay Number: 167
• Rated Voltage [V]: 12
• Current Strength [A]: 40
• Number of pins: 5
• Name: RELEE, KšTUSEPUMP
• Manufacturer: HAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Vehicle Identification Number (VIN) to: 6N-WW001 001, 6N-WY000 158, 6N-YY050 000
• Relay Number: 8
• Vehicle Identification Number (VIN) from: 6N-WW001 002, 6N-WY000 159
• Voltage [V]: 12
• Rated current [A]: 5
• Number of pins: 6
• Manufacturer: DELLO AUTOMEGA

• Relay function: Sunroof
• Combi Switch Function: Normally Open Contact
• Voltage [V]: 12
• Name: Mitme funktsiooniga relee
• Manufacturer: MAX

• Current Strength [A]: 10
• Fitting Position: Vehicle Windscreen
• Voltage [V]: 12
• Manufacturer: JP GROUP
• Lisainfo: Relay for wiper and washer, front, 12 Volt, 10 Amp
• Additional information: Relay for wiper and washer, front, 12 Volt, 10 Amp

Vehicle Equipment: for vehicles without controllable wiper intervals, for vehicles without rain sensor

• Voltage [V]: 12
• Number of pins: 4
• Capacity at 12V: 40A
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Quantity: 1
• Vehicle Identification Number (VIN) to: 6N-WW001 001, 6N-WY000 158
• Vehicle Identification Number (VIN) from: 6N-WW001 002, 6N-WY000 159
• Weight [kg]: 0.035
• Required quantity: 1
• Number of connectors: 4
• General Information: fuel pump relay
• Manufacturer: VIKA

• Vehicle Equipment: for vehicles without controllable wiper intervals
• Rated Voltage [V]: 12
• Supplementary Article/Info 2: for windscreen cleaning
• Name: RELEE,KOJAMEHED-PESU-INTERVALL
• Manufacturer: HAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Number of pins: 4
• Voltage [V]: 12
• Current Strength [A]: 70
• Relay function: Normally open contact
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Operating voltage [V]: 12
• Rated Power [W]: 480
• Rated current [A]: 40
• Combi Switch Function: Normally Open Contact
• Length [mm]: 28
• Width [mm]: 28
• Height [mm]: 25
• Connector type: 2x 6,3 mm, 2x 9,5 mm
• Number of pins: 4
• Name: MITME FUNKTSIOONIGA RELEE
• Manufacturer: MEY

Relay function: Fuel Pump, Engine control unit, Surge protection, Suction pipe pre-heating, Interior Blower, Heated rear window, Battery main switch, Heated windscreen, Fan, heater/air conditioning, Rear window wiper, Water pump after-run, Secondary Air System, Electric booster heater, engine cooling, Normally open contact, Clamp 15, Parking Heater, X contact relief, Window Regulator, Terminal 75, Sunroof, Pump, fuel pre-supply, Start-stop system, Magnetic clutch

• Voltage [V]: 12
• Current Strength [A]: 30
• Weight [kg]: 0.025
• Number of connectors: 4
• Supplementary Article/Supplementary Info: with holder
• General Information: relay
• Manufacturer: BORSEHUNG

• Relay Number: 67, 80, 167
• Number of connectors: 4
• Weight [kg]: 0.035
• Name: RELEE, KšTUSEPUMP
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• General Information: fuel pump relay
• Manufacturer: VIKA

• General Information: relay
• Manufacturer: BORSEHUNG

• for OE number: 191 906 383 C
• Number of connectors: 4
• Relay function: Normally open contact
• Rated current [A]: 40
• Voltage [V]: 12
• Manufacturer: TRUCKTEC

• Vehicle Equipment: for vehicles without trailer hitch
• Relay Number: 21, 191
• Voltage [V]: 12
• Rated Power [W]: 21
• Number of connectors: 3
• Colour: black
• Material: Plastic
• Operating Mode: Electronic
• Weight [kg]: 0.032
• Name: SUUNATULEDE LšLITI
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Operating voltage [V]: 12
• Rated current [A]: 40
• Combi Switch Function: Normally Open Contact
• Length [mm]: 28
• Width [mm]: 28
• Height [mm]: 24.5
• Connector type: 1x 6,3 mm, 2x 9,5 mm, 1x 2,8 mm
• Number of pins: 4
• Name: MITME FUNKTSIOONIGA RELEE
• Manufacturer: MEY

Relay function: Fuel Pump, Exterior Rearview Mirror Adjustment, Normally open contact, Fan, engine cooling, Suction pipe pre-heating

• Voltage [V]: 12
• Number of pins: 6
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Current Strength [A]: 40
• Relay function: Terminal 30, Clamp 87
• Rated current [A]: 40
• Weight [kg]: 0.04
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Voltage [V]: 12
• Switching Capacity [W]: 21
• Mounting Type: Flat Plug-in Connector
• Operating Mode: Electric
• Number of pins: 3
• Plug Type: Blade Terminal
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Operating voltage [V]: 12
• Switching Capacity [W]: 4x21

• for OE number: 111 963 141 C
• Combi Switch Function: Normally Open Contact
• Current Strength [A]: 30
• Voltage [V]: 12
• Number of pins: 5
• Relay function: Normally open contact
• Housing Type: Synthetic Material Housing
• Temperature range from [°C]: -40
• Temperature range to [°C]: 100
• Housing Colour: black
• Supplementary Article/Supplementary Info: with holder
• Resistor [Ohm]: 90
• Manufacturer: BOSCH

• Quantity: 1
• Vehicle Identification Number (VIN) to: 6N-WW001 001, 6N-WY000 158
• Vehicle Identification Number (VIN) from: 6N-WW001 002, 6N-WY000 159
• General Information: control unit for radiator fan
• Manufacturer: VIKA

• General Information: relay
• Manufacturer: BORSEHUNG

• Operating voltage [V]: 12
• Rated Power [W]: 120
• Rated current [A]: 10
• Combi Switch Function: Normally Open Contact
• Length [mm]: 30
• Width [mm]: 30
• Height [mm]: 42
• Connector type: 1x 2,8 mm, 5x 6,3 mm
• Number of pins: 6
• Name: RELEE,KOJAMEHED-PESU-INTERVALL
• Manufacturer: MEY

• Voltage [V]: 12
• Operating Mode: Electric
• Vehicle Equipment: for vehicles with factory mounted tow bar
• Number of pins: 4
• Weight [kg]: 0.023
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Vehicle Identification Number (VIN) to: 6N-WY000 158, 6N-WW001 001
• Voltage [V]: 12
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 4RP008189151

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Mounting Type: Plugged
• Operating Mode: Electronic
• Switching Capacity [W]: 2(4)x21W+0...5
• Number of pins: 3
• Voltage [V]: 12
• Registration Type: ECE approved
• Temperature range from [°C]: -40
• Temperature range to [°C]: 70
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 4DB003750711

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Voltage [V]: 12
• Number of pins: 6
• Weight [kg]: 0.04
• Fitting Position: Engine Compartment
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 10, 4
• Rated Voltage [V]: 12
• Housing material: Polyamid 6.6, GRP (Glass fibre Reinforced Plastic)
• Fabrication Number: CSW-VW-006
• Manufacturer: NTY
• Name: NTY CSW-VW-006

• Length [mm]: 30.5
• Width [mm]: 30.5
• Height [mm]: 57
• Operating Mode: Electric
• Vehicle Equipment: for vehicles without trailer hitch
• Manufacturer: BOSCH

• Mounting Type: mounting
• Operating Mode: Electronic
• Switching Capacity [W]: 2+1(6)x21W+5 EP
• Number of pins: 4
• Voltage [V]: 12
• Supplementary Article/Info 2: for trailer
• Supplementary Article/Supplementary Info: with holder
• Registration Type: ECE approved
• Temperature range from [°C]: -40
• Temperature range to [°C]: 85
• Assy./disassy. by qualified personnel required!:
• Name: Suunatulede lliti
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Vehicle Identification Number (VIN) from: F6N-WW001001, F6N-WY000158
• Voltage [V]: 12
• Weight [kg]: 0.038
• Fitting Position: Engine Compartment
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Supplementary Article/Supplementary Info: without holder
• Voltage [V]: 12
• Temperature range from [°C]: -30
• Temperature range to [°C]: +85
• Number of pins: 6
• Assy./disassy. by qualified personnel required!:
• Name: HE 5WG003620097
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Voltage [V]: 12
• Current Strength [A]: 5
• Number of connectors: 6
• Manufacturer: ERA

• Supplementary Article/Supplementary Info: without holder
• Voltage [V]: 12
• Temperature range from [°C]: -30
• Temperature range to [°C]: +85
• Number of pins: 6
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 5WG003620091

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Vehicle Identification Number (VIN) from: 6N-WW001002, 6N-WY000159
• Rated Voltage [V]: 12
• Number of pins: 10, 4
• Housing material: Polyamid 6.6, GRP (Glass fibre Reinforced Plastic)
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Weight [kg]: 0.23
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY
• Name: CE 96SKV206

• Vehicle Equipment: for vehicles with air conditioning
• Vehicle Identification Number (VIN) to: 6N-WW001001, 6N-WY000158
• Rated Voltage [V]: 12
• Relay function: Radiator Fan Overrun, Fan, engine cooling
• Manufacturer: HAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty. Name: PRZEKANIK WENTYLATORA FORD GALAXY I SEAT ALHAMBRA, CORDOBA, IBIZA II, INCA VW CADDY II, GOLF III, PASSAT B3/B4, POLO III

• Mounting Type: Plugged
• Operating Mode: Electronic
• Switching Capacity [W]: 2+1(6)x21W EP
• Number of pins: 5
• Voltage [V]: 12
• Supplementary Article/Info 2: for trailer
• Observe illustration:
• Registration Type: ECE approved
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead
• Name: SUUNATULEDE LšLITI
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Rated Voltage [V]: 12
• Number of pins: 14
• Protection Type (IP Code): IP 54K
• Name: Juhtseade,elektrovent.(mootorijahut.)
• Manufacturer: MAX

• Number of pins: 13
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Vehicle Identification Number (VIN) from: 6N-WW001002, 6N-WY000159
• Voltage [V]: 12
• Number of connectors: 13
• Weight [kg]: 0.178
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 18
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.