• Engine Code: 1H
• Transmission Type: Manual Transmission
• Catalytic Converter Type: for vehicles with catalytic converter
• Exhaust System: for pre-catalytic converter
• for OE number: 030906265
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 986
• Number of pins: 3
• Weight [g]: 113
• Gross Weight [g]: 143
• Manufacturer: DENSO

Lambda Sensor: Regulating Probe, Heated, Finger probe, Lambda Sensor Additional information: "Tootja: DENSO
POLO (86C, 80), 10.8
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
POLO (86C, 80), 10.8
(kvaliteediklass: Q)"

• Thread Size: M10x1,0
• Colour: black
• Number of connectors: 1
• Weight [kg]: 0.019
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 2
• Connector Shape: rectangular
• Socket colour: blue
• Diameter [mm]: 25.5
• Fitted Diameter [mm]: 20
• for OE number: 025 906 041 A, 95VW-12A648-BA, A 002 542 07 18
• Manufacturer: MEAT&DORIA

• Number of pins: 2
• Connector Shape: rectangular
• Socket colour: black
• Sensor Type: NTC Sensor
• Diameter [mm]: 25.5
• Fitted Diameter [mm]: 20
• for OE number: 251 919 501 D
• Voltage [V]: 12
• Manufacturer: MEAT&DORIA

• Engine Code: 1H
• Number of pins: 1
• Colour: black
• Thread Size: M10x1
• Spanner Size: 13
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• General Information: temperature sensor
• Manufacturer: VIKA

• Engine Code: 1H
• Diameter [mm]: 26
• Length [mm]: 35
• Weight [kg]: 0.02
• Supplementary Article/Info 2: with seal ring
• for OE number: 251 919 501 D
• Housing Colour: black
• Supplementary Article/Supplementary Info: with seal
• Number of pins: 2
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 2
• Connector Shape: rectangular
• Socket colour: white
• Thread Size: M 10x1
• Spanner Size: 19 mm
• for OE number: 026 906 161
• Manufacturer: MEAT&DORIA

• Number of pins: 3
• Socket colour: blue
• Fabrication Number: ESS-AU-001
• Manufacturer: NTY

• Number of pins: 3
• Socket colour: green
• Fabrication Number: ESS-AU-000
• Manufacturer: NTY

• Engine Code: 1H
• Number of pins: 2
• Colour: blue
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Engine Code: PG
• Thread Size: M14x1,5
• Colour: white
• Spanner Size: 19
• Supplementary Article/Supplementary Info: with seal
• Number of pins: 2
• Weight [kg]: 0.034
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Catalytic Converter Type: for vehicles with catalytic converter
• Length [mm]: 37
• Weight [kg]: 0.02
• Supplementary Article/Info 2: with seal ring
• for OE number: 025 906 041 A
• Supplementary Article/Supplementary Info: with seal
• Colour Coding: blue
• Number of pins: 2
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: PG
• Thread Size: M10x1,0
• Colour: white
• Spanner Size: 19
• Supplementary Article/Supplementary Info: with seal
• Number of pins: 2
• Weight [kg]: 0.029
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Cable Length [mm]: 730
• Manufacturer: KAMOKA

• Engine Code: 1H
• Number of pins: 2
• Colour: black
• Manufacturer: EPS

• Engine Code: 1H
• Number of pins: 2
• Colour: white
• Thread Size: M10x1
• Spanner Size: 19
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Construction Year from: 01.1990
• Construction Year to: 07.1991
• Cable Length [mm]: 520
• Number of pins: 3
• Colour: blue, black
• Manufacturer: DELLO AUTOMEGA

• Number of pins: 2
• Housing Colour: blue
• Fitted Diameter [mm]: 20
• Manufacturer: FAE

• Construction Year from: 01.1989
• Engine Code: PG
• Mounting Type: Plugged
• Voltage [V]: 12
• Resistor [Ohm]: 2,080, 322
• Supplementary Article/Supplementary Info: with seal
• Temperature range from [°C]: 25
• Temperature range to [°C]: 80
• Colour: blue
• Sensor Type: NTC Sensor
• Number of pins: 2
• Supplementary Article/Info 2: with retaining ring
• Corresponds to the original part in colour: blue
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PT009107551

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Engine Code: 1H
• Colour: green, black
• Manufacturer: DELLO AUTOMEGA

• Construction Year from: 04.1989
• Housing Colour: white
• Thread Size: M10 x 1,0
• Number of pins: 2
• Supplementary Article/Supplementary Info: with seal
• Temperature range [°C]: 25, 80
• Power [W]: 0.06
• Manufacturer: METZGER

• Engine Code: 1H
• Cable Length [mm]: 800
• Name: DETONATSIOONIANDUR
• Manufacturer: MAX

• Number of pins: 3
• Connector Shape: rectangular
• Cable Length [mm]: 550
• for OE number: 054 905 377 G, 480EE-1002060
• Manufacturer: MEAT&DORIA

• Diameter [mm]: 90
• Length [mm]: 835
• Height [mm]: 37
• General Information: knock sensor
• Manufacturer: VIKA

• Cable Length [mm]: 520
• Number of pins: 3
• Weight [kg]: 0.08
• Manufacturer: ERA

• Cable Length [mm]: 535
• Number of pins: 3
• Housing Colour: blue
• Lisainfo: Knock sensor
• Additional information: Knock sensor

• Number of pins: 3
• Colour: black
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Cable insulation material: Silicone
• Cable Length [mm]: 500
• Manufacturer Restriction: VAG
• Number of pins: 2
• Cable Cross Section [mm²]: 1
• Contact surface: Tin-plated
• Socket Width [mm]: 2.8
• Supplementary Article/Supplementary Info: with socket housing, with seal
• Supplementary Article/Info 2: with pipe
• Temperature range from [°C]: -25
• Temperature range to [°C]: +140
• SVHC: No SVHC present!
• Name: Kaabli remondikomplekt, numbrivalgustus
• Manufacturer: HBE

• Plug housing design: Plug sleeve housing
• Manufacturer Restriction: BMW, Volvo, VAG
• Number of pins: 3
• Cable Length [mm]: 250
• Cable Cross Section [mm²]: 1
• Supplementary Article/Supplementary Info: with socket housing, with gaskets/seals
• Supplementary Article/Info 2: with pipe
• Temperature range from [°C]: -25
• Temperature range to [°C]: +140
• Cable insulation material: Silicone
• SVHC: No SVHC present!
• Manufacturer: HBE

Name: Kaabliparanduskomplekt, seadeelement- tulede ulatuse regul

• Engine Code: PG
• Vehicle Identification Number (VIN) to: 1G-N-300 000
• for OE number: 035906265B
• Alternatively:
• Lambda Sensor: Planar probe
• Manufacturer: DELLO AUTOMEGA

• Number of circuits: 3
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Engine Code: 1H, PG
• Construction Year from: 04.1989, 01.1990
• Construction Year to: 12.1989, 07.1991
• Colour: white
• Block Separation:
• Manufacturer: BOSCH

• Engine Code: 1H
• Construction Year from: 04.1989
• Construction Year to: 07.1989
• Colour: green
• Manufacturer: BOSCH

• Engine Code: PG
• Construction Year from: 01.1990
• Construction Year to: 07.1991
• Colour: blue
• Name: DETONATSIOONIANDUR
• Manufacturer: BOS

• Lambda Sensor: Regulating Probe, Lambda Sensor
• Engine Code: 1H, PG
• Voltage [V]: 12
• Number of circuits: 3
• Weight [kg]: 0.08
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV903

• Engine Code: PG
• Colour: blue
• Length [mm]: 570
• Manufacturer: EPS

• Cable Length [mm]: 550
• Number of pins: 3
• Housing Colour: blue
• Manufacturer: FAE

• Lambda Sensor: Regulating Probe, Heated
• Fitting Position: Exhaust Manifold
• Number of pins: 3
• Cable Length [mm]: 230
• for article number: 81014E
• Quality: OE EQUIVALENT
• Manufacturer: MEAT&DORIA

• Diameter [mm]: 90
• Length [mm]: 570
• Height [mm]: 37
• Cable Length [mm]: 535
• Weight [kg]: 0.07
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Cable Length [mm]: 800
• Number of pins: 3
• Housing Colour: green
• Manufacturer: FAE

• Engine Code: PG
• Construction Year from: 01.1990
• Construction Year to: 07.1991
• Lambda Sensor: Regulating Probe, Planar probe
• Fitting Position: before catalytic converter
• Number of circuits: 3
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Lambda Sensor: Regulating Probe, Lambda Sensor
• Engine Code: 1H, PG
• Exhaust System: for pre-catalytic converter
• Voltage [V]: 12
• Number of circuits: 4
• Weight [kg]: 0.09
• Resistor [Ohm]: 13
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV913
• Manufacturer: ESEN SKV

• Engine Code: PG
• Construction Year from: 04.1990
• Lambda Sensor: Regulating Probe
• Number of circuits: 4
• Supplementary Article/Info 2: without plug
• Manufacturer: ENERGY

• Engine Code: 1H
• Transmission Type: Manual Transmission
• Catalytic Converter Type: for vehicles with catalytic converter
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 3
• Weight [g]: 95
• Gross Weight [g]: 144
• Manufacturer: DENSO
• Name: DN DOX-0116
• Lisainfo: DOX-0116 DENSO
• Additional information: DOX-0116 DENSO

Lambda Sensor: Regulating Probe, Heated, Finger probe, Lambda Sensor

• Construction Year from: 04.1990
• Lambda Sensor: Regulating Probe
• Voltage [V]: 12
• Length [mm]: 583
• Number of circuits: 4
• Weight [kg]: 0.15
• Resistor [Ohm]: 4.5
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Engine Code: PG
• Transmission Type: Manual Transmission
• Catalytic Converter Type: for vehicles without catalytic convertor
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 3
• Weight [g]: 95
• Gross Weight [g]: 144
• Manufacturer: DENSO
• Name: Lambda sensor
• Quality class: Q

Lambda Sensor: Regulating Probe, Heated, Finger probe, Lambda Sensor Additional information: "Tootja: DENSO
ESCORT IV KOMBI (AWF
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
ESCORT IV KOMBI (AWF
(kvaliteediklass: Q)"

• Construction Year from: 04.1990
• Lambda Sensor: Regulating Probe, Finger probe, Heated
• Engine Code: PG
• Cable Length [mm]: 985
• Manufacturer: DELPHI

• Engine Code: 1H
• Construction Year to: 12.1989
• Transmission Type: Manual Transmission
• Line insulation design: with silicone-coated woven-fibre insulation
• Cable Length [mm]: 1,255
• Socket colour: black
• Connector Shape: rectangular
• Thread Size: M18 x 1,5
• Weight [kg]: 0.152
• for OE number: 030 906 265 C
• Length [mm]: 1,020
• Number of pins: 3
• Lambda Sensor: Regulating Probe, Thread pre-greased
• Number of circuits: 3
• Exhaust System: before catalytic converter
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year from: 04.1989
• Construction Year to: 12.1989
• Lambda Sensor: Regulating Probe, Finger probe, Heated
• Engine Code: 1H
• Cable Length [mm]: 985
• Manufacturer: DELPHI

• Engine Code: 1H
• Construction Year from: 04.1989
• Construction Year to: 12.1989
• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 3
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Engine Code: PG
• Construction Year from: 01.1990
• Construction Year to: 07.1991
• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 3
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS