Assembly categories
Filter Brakes Suspension Steering Cooling/Air Conditioning Electrics Accessories Drive Train Exhaust System Body Spark/Glow Ignition Engine Windows/Window Cleaning Lights Fuel Mixture Formation Interior Equipment ServiceProduct
Description
In stock
Price
(incl. VAT)
- Inner Diameter [mm]: 50
- Thickness [mm]: 4
-
Material: NBR
(nitrile butadiene rubber) - Manufacturer: METZGER
- Thickness [mm]: 3.65
- Weight [kg]: 0.001
- Inner Diameter [mm]: 19.6
- Manufacturer: METALCAUCHO
- Material: Paper
- Fitting Position: engine sided
- Manufacturer: TOPRAN
General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.
- Engine Code: 2G
- Forward- /Backflow: for backflow
Lisainfo: Radiator hose, thermostat housing to intake manifold Additional information: Radiator hose, thermostat housing to intake manifold
-
Vehicle Identification Number (VIN) from: 1G-
NW300 001, 1G- NB050 001, 1G- NP060 000 -
Engine Code: 2G,
NZ - Cooling Hose: Piping to heat exchanger
- Forward- /Backflow: for backflow
- Manufacturer: DELLO AUTOMEGA
-
Engine Code: 2G,
NZ -
Vehicle Identification Number (VIN) from: 1G-
N- 060001, 1G- NW300001 - Material: Rubber with fabric lining
- Cooling Hose: from expansion tank to water pipe
- Fitting Position: Lower
- Observe system fill quantity:
- Hose Type: Moulded Hose
- Name: JAHUTUSVOOLIK
- Manufacturer: HAN
General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.
-
Vehicle Identification Number (VIN) to: 1G-
L- 990 000 - Forward- /Backflow: for foreflow
- Manufacturer: DELLO AUTOMEGA
- Material: Rubber with fabric lining
- Cooling Hose: from coolant regulator housing to intake manifold
- Forward- /Backflow: for backflow
- Observe system fill quantity:
- Hose Type: Moulded Hose
- Name: JAHUTUSVOOLIK
- Manufacturer: HAN
General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.
-
Engine Code: 2G,
NZ - Construction Year to: 10.1991
- Material: Rubber with fabric lining
- Cooling Hose: from heat exchanger to water pipe
- Forward- /Backflow: for backflow
- Hose Type: Moulded Hose
- Name: JAHUTUSVOOLIK
- Manufacturer: HAN
General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.
-
Vehicle Identification Number (VIN) from: 1G-
N- 060001, 1G- NW300001 - Cooling Hose: from expansion tank to water pipe
-
Lisainfo: Radiator hose,
expansion tank to water pipe -
Additional information: Radiator hose,
expansion tank to water pipe
-
Engine Code: 2G,
NZ -
Vehicle Identification Number (VIN) from: 1G-
NP060001, 1G- NW300001, 1G- NB050001 - Cooling Hose: from heat exchanger to water pipe
- Forward- /Backflow: for backflow
- Hose Type: Moulded Hose
- Name: JAHUTUSVOOLIK
- Manufacturer: HAN
Material: EPDM (ethylene propylene diene Monomer (M-class) rubber) General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.
-
Vehicle Identification Number (VIN) from: 1G-
NG050 001, 1G- NP060 001, 1G- NW300 001 - Length [mm]: 315
- Cooling Hose: from expansion tank to water pipe
- Weight [kg]: 0.085
- Name: JAHUTUSVOOLIK
- Manufacturer: FEB
General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.
- Weight [kg]: 0.28
- Warranty: 3 years warranty
- Always compare old and new part (in particular OE No.):
- Name: CE 24SKV393
- Manufacturer: ESEN SKV
-
Engine Code: 2G,
NZ -
Vehicle Identification Number (VIN) to: 1G-
L- 990000 - Material: Rubber with fabric lining
- Cooling Hose: from coolant regulator housing to engine cooler
- Fitting Position: Upper
- Observe system fill quantity:
- Hose Type: Moulded Hose
- Name: JAHUTUSVOOLIK
- Manufacturer: HAN
General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.
- Construction Year to: 10.1991
- Cooling Hose: from connecting pipe to engine cooler
- Name: Jahutusvoolik
- Manufacturer: MAX
-
Vehicle Identification Number (VIN) to: 1G-
L- 990000 - Cooling Hose: from coolant regulator housing to engine cooler
Lisainfo: Radiator hose, upper, radiator to coolant regulator housing Additional information: Radiator hose, upper, radiator to coolant regulator housing
- Fitting Position: Lower
-
Country Specific Design: Sweden,
Switzerland - Colour: black
- Hose Length [mm]: 385
- Inner Diameter 1 [mm]: 30.5
- Inner Diameter 2 [mm]: 30.5
- Observe broschure:
- Name: Jahutusvoolik
- Manufacturer: GAT
Material: EPDM (ethylene propylene diene Monomer (M-class) rubber)
- Vehicle Identification Number (VIN) to: 1GL990 000
-
not for country specific design: Sweden,
Switzerland -
Cut-off Marking:
(1) - Fitting Position: Upper
- Cooling Hose: from thermostat to radiator
- Weight [kg]: 0.231
- Manufacturer: VAICO
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Material: Rubber with fabric lining
- Cooling Hose: from coolant regulator housing to engine cooler
- Fitting Position: Lower
- Observe system fill quantity:
- Hose Type: Moulded Hose
- Manufacturer: TOPRAN HANS PRIES
General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.
- Fitting Position: Upper
- Vehicle Identification Number (VIN) to: 1GL990 000
-
not for country specific design: Sweden,
Switzerland -
Cut-off Marking:
(1) - Colour: black
- Hose Length [mm]: 435
- Inner Diameter 1 [mm]: 31
- Inner Diameter 2 [mm]: 31
- Observe broschure:
- Manufacturer: GATES PASKI PRZEWODY
Material: EPDM (ethylene propylene diene Monomer (M-class) rubber)
-
not for country specific design: Sweden,
Switzerland -
Fitting Position: Exhaust Side,
Lower - Material: Rubber with fabric lining
- Cooling Hose: from engine cooler to water pump
- Weight [kg]: 0.26
- Manufacturer: VAICO
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Construction Year to: 10.1991
- Cooling Hose: from connecting pipe to engine cooler
- Supplementary Article/Info 2: without clamps
- Name: JAHUTUSVOOLIK
- Manufacturer: MEY
Material: EPDM (ethylene propylene diene Monomer (M-class) rubber)
- for OE number: 3293561
- Fitting Position: Upper Right
- Weight [g]: 270
- Length [mm]: 366
- Name: Jahutusvoolik
- Manufacturer: IMP
- Cooling Hose: from connecting pipe to engine cooler
- Fitting Position: Upper Right
- for OE number: 191121101S
- Manufacturer: SASIC
- Lisainfo: Water pipe
- Additional information: Water pipe
- Weight [kg]: 0.21
- Weight [g]: 210
- Manufacturer: METALCAUCHO
-
Engine Code: 2G,
MH -
Vehicle Identification Number (VIN) to: 1G-
N- 300 000 - Weight [kg]: 0.174
- Manufacturer: VAICO
Cooling Hose: Intake Manifold to Thermostat, from engine to thermostat, from thermostat to carburettor General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- for OE number: 030121054
- Weight [g]: 234
- Number of circuits: 3
- Length [mm]: 466
- Inner Diameter 1 [mm]: 18
- Inner Diameter 2 [mm]: 18
- Inner Diameter 3 [mm]: 10
- Name: IM 220731
- Manufacturer: ORIGINAL IMPERIUM
- General Information: coolant pipe; iron
- Manufacturer: VIKA
- Material: Rubber
- Specification: flexibel
- Inner Diameter 1 [mm]: 32
- Inner Diameter 2 [mm]: 32
- Length [mm]: 508