• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Length [mm]: 373
• Number of pins: 4
• Lambda Sensor: Thread pre-greased
• Fabrication Number: ESL-FR-008

Lisainfo: ENG. 1,4,1.6,1.8,2.0 FORD FOCUS 04-, C-MAX 07-, MONDEO IV 07-15, GALAXY II 06-15, S-MAX 06-14, VOLVO C30 06-12, S40 II 04-12, S60 II 10-14, S80 II 08-16, XC60 09-17 /REGULACYJNA, Dœ.CAœK. 373MM Additional information: ENG. 1,4,1.6,1.8,2.0 FORD FOCUS 04-, C-MAX 07-, MONDEO IV 07-15, GALAXY II 06-15, S-MAX 06-14, VOLVO C30 06-12, S40 II 04-12, S60 II 10-14, S80 II 08-16, XC60 09-17 /REGULACYJNA, Dœ.CAœK. 373MM

• Lambda Sensor: Lambda Sensor
• Length [mm]: 373
• Number of pins: 4
• Warranty: 3 years warranty
• Name: CE 09SKV135
• Manufacturer: ESEN SKV

• Lambda Sensor: Diagnostic Probe, Planar probe
• Fitting Position: after catalytic converter
• Number of pins: 4
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Lambda Sensor: Lambda Sensor
• Voltage [V]: 12
• Number of circuits: 4
• Weight [kg]: 0.09
• Resistor [Ohm]: 9
• Operating Mode: Electric
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY
• Name: CE 09SKV909

• Lambda Sensor: Diagnostic Probe, Planar probe, Heated
• Fitting Position: after catalytic converter
• Cable Length [mm]: 375
• Manufacturer: DELPHI
• Name: DE ES20025-12B1
• Additional information: ES20025-12B1 DELPHI
• Lisainfo: ES20025-12B1 DELPHI

• Lambda Sensor: Lambda Sensor
• Voltage [V]: 12
• Length [mm]: 393
• Number of circuits: 4
• Weight [kg]: 0.1
• Operating Mode: Electric
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY
• Name: CE 09SKV048

• Exhaust System: after catalytic converter
• Lambda Sensor: Diagnostic Probe, Regulating Probe
• Length [mm]: 525
• Number of connectors: 4
• Manufacturer: VERNET

• Lambda Sensor: Diagnostic Probe, Lambda Sensor
• Engine Code: IQDA, IQDB
• Voltage [V]: 12
• Length [mm]: 770
• Number of circuits: 4
• Weight [kg]: 0.12
• Operating Mode: Electric
• Warranty: 3 years warranty
• Name: CE 09SKV003
• Manufacturer: ESEN SKV

• Lambda Sensor: Regulating Probe, Unheated
• Number of pins: 4
• Connector Shape: round
• Cable Length [mm]: 330
• for OE number: 3M51 9F472 DC
• Manufacturer: MEAT&DORIA

• Lambda Sensor: Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 400
• Weight [kg]: 0.085
• for OE number: 1 300 544
• Name: SW 33 10 3139
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Lambda Sensor: Heated, Regulating Probe
• Cable Length [mm]: 400
• Thread Size: M18 x 1,5
• Number of pins: 4
• Connector Shape: rectangular
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Conductor Number: 4
• Resistor [Ohm]: 9
• Length [mm]: 478
• Number of circuits: 4
• Cable Length [mm]: 478
• Lambda Sensor: Heated
• Manufacturer: MAGNETI MARELLI
• Name: MM OSM125

• Lambda Sensor: Lambda Sensor
• Cable Length [mm]: 290
• Alternatively:
• Number of circuits: 4
• Alternative Repair Kit: 570112
• Manufacturer: ERA

• Length [mm]: 345
• Conductor Number: 4
• Resistor [Ohm]: 9
• Number of circuits: 4
• Cable Length [mm]: 345
• Lambda Sensor: Heated
• Manufacturer: MAGNETI MARELLI
• Name: MM OSM070

• Lambda Sensor: Lambda Sensor
• Cable Length [mm]: 390
• Number of circuits: 4
• Manufacturer: ERA

• Engine Code: IQDA
• Fitting Position: after catalytic converter
• Required quantity: 1
• Cable Length [mm]: 500
• Conductor Number: 4
• Available as universal article as well, see article no.: 1.998.235
• Number of circuits: 4
• Name: EP 1.998.296
• Manufacturer: EPS

Lambda Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased

• Lambda Sensor: Diagnostic Probe, Heated
• Number of pins: 4
• Cable Length [mm]: 600
• Quality: OE EQUIVALENT
• Manufacturer: MEAT&DORIA

• Lambda Sensor: Regulating Probe, Thread pre-greased
• Line insulation design: with silicone-coated woven-fibre insulation
• Thread Size: M18 x 1,5
• Connector Shape: round
• Length [mm]: 400
• Cable Length [mm]: 400
• Conductor Number: 4
• Weight [kg]: 0.129
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Diagnostic Probe
• Voltage [V]: 12
• Length [mm]: 720
• Number of circuits: 4
• Weight [kg]: 0.15
• Resistor [Ohm]: 9
• Operating Mode: Electric
• Warranty: 3 years warranty
• Name: CE 09SKV577
• Manufacturer: ESEN SKV

• Line insulation design: with silicone-coated woven-fibre insulation
• Number of pins: 4
• for OE number: V99760001
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Length [mm]: 350
• Exhaust System: after catalytic converter
• Manufacturer: VEMO GERMANY

Lambda Sensor: Regulating Probe, Finger probe, Heated, Thread pre-greased Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Conductor Number: 4
• Resistor [Ohm]: 9
• Length [mm]: 525
• Number of circuits: 4
• Cable Length [mm]: 525
• Lambda Sensor: Heated
• Manufacturer: MAGNETI MARELLI
• Name: MM OSM090

• Construction Year to: 03.2015
• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter, Right
• Wheelbase: short wheelbase, long wheelbase
• Block Separation:
• Number of circuits: 4
• Manufacturer: BOSCH
• Name: BS 0258986777

• Wheelbase: short wheelbase
• Recommended change interval [km]: 250,000
• Lambda Sensor: Heated, Diagnostic Probe
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Fitting Position: after catalytic converter
• Cable Length [mm]: 390
• Weight [kg]: 0.112
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: before catalytic converter
• Required quantity: 1
• Lambda Sensor: Regulating Probe
• Cable Length [mm]: 350
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PA358103211

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Line insulation design: with silicone-coated woven-fibre insulation
• Lambda Sensor: Planar probe, Heated, Thread pre-greased
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Manufacturer: VEMO GERMANY

Fitting Position: before catalytic converter, after catalytic converter Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 03.2015
• Lambda Sensor: Regulating Probe, Diagnostic Probe
• Wheelbase: short wheelbase, long wheelbase
• Block Separation:
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Manufacturer: BOSCH
• Name: BS 0258986602

Fitting Position: before catalytic converter, after catalytic converter, Left, Right

• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 93
• Gross Weight [g]: 140
• Manufacturer: DENSO
• Name: DN DOX-0150
• Quality class: Q

Lambda Sensor: Regulating Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
(kvaliteediklass: Q)"

• Construction Year to: 03.2015
• Lambda Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter, Left
• Wheelbase: long wheelbase
• Number of circuits: 4
• Overall Length [mm]: 628
• Available as universal article as well, see article no.: 0258986602
• Recommended change interval [km]: 250,000
• Manufacturer: BOSCH
• Name: BS 0258006571

• Lambda Sensor: Regulating Probe, Thread pre-greased
• Line insulation design: with silicone-coated woven-fibre insulation
• Thread Size: M18 x 1,5
• Cable Length [mm]: 320
• Conductor Number: 4
• Connector Shape: round
• Length [mm]: 450
• Number of pins: 4
• Weight [kg]: 0.13
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• for OE number: 1351337, 1088851
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 450
• Number of pins: 4
• Weight [g]: 95
• Gross Weight [g]: 128
• Manufacturer: DENSO
• Name: DN DOX-2004
• Quality class: Q

Lambda Sensor: Regulating Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
FOCUS II KOMBI (DAW/
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
FOCUS II KOMBI (DAW/
(kvaliteediklass: Q)"

• Construction Year to: 03.2015
• Lambda Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Wheelbase: short wheelbase
• Overall Length [mm]: 557
• Manufacturer: BOSCH
• Name: BS 0258986785

• Fitting Position: before catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Number of pins: 4
• Socket colour: purple
• Number of circuits: 4
• Lambda Sensor: Heated, Thread pre-greased
• Connector Shape: round
• Cable Length [mm]: 240
• Thread Size: M18 x 1,5
• Weight [kg]: 0.12
• for OE number: 2S6A 9G444 BA
• Length [mm]: 300
• Number of connectors: 4
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 03.2015
• Engine Code: IQDB
• Fitting Position: before catalytic converter
• Lambda Sensor: Planar probe, Thread pre-greased, Heated
• Number of pins: 4
• Cable Length [mm]: 350
• Thread Size: M18x1,5
• Switch Pressure [bar]: 4
• Weight [kg]: 0.13
• Name: VA 368031
• Manufacturer: VALEO

• for OE number: 1536254, 1322706
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 525
• Number of pins: 4
• Weight [g]: 118
• Gross Weight [g]: 151
• Manufacturer: DENSO

Lambda Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
FOCUS C-MAX, 10.03-0
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
FOCUS C-MAX, 10.03-0
(kvaliteediklass: Q)"

• Fitting Position: Left
• for OE number: 1327549, 1302222
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 725
• Number of pins: 4
• Weight [g]: 126
• Gross Weight [g]: 159
• Manufacturer: DENSO
• Name: DN DOX-2068

Lambda Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 660
• Number of pins: 4
• Weight [kg]: 0.119
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 03.2015
• Fitting Position: Right, after catalytic converter
• Lambda Sensor: Diagnostic Probe, Heated
• Length [mm]: 800
• Technical Information Number: Universal 77015
• Manufacturer: FAE

• Wheelbase: long wheelbase
• Lambda Sensor: Regulating Probe
• Number of circuits: 4
• Cable Length [mm]: 478
• Fitting Position: Right
• Manufacturer: METZGER

• Construction Year to: 03.2015
• Engine Code: IQDB
• Lambda Sensor: Planar probe, Thread pre-greased, Heated
• Number of pins: 4
• Cable Length [mm]: 720
• Thread Size: M18x1,5
• Switch Pressure [bar]: 4
• Weight [kg]: 0.123
• Name: VA 368239
• Manufacturer: VALEO

Fitting Position: before catalytic converter, after catalytic converter

• Fitting Position: Right
• Wheelbase: long wheelbase
• Lambda Sensor: Diagnostic Probe
• Number of circuits: 4
• Cable Length [mm]: 725
• Manufacturer: METZGER