• Number of pins: 2
• Lisainfo: Sender Unit, coolant temperature
• Additional information: Sender Unit, coolant temperature

• for OE number: MD348431
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 420
• Number of pins: 4
• Weight [g]: 88
• Gross Weight [g]: 121
• Manufacturer: DENSO

Lambda Sensor: Diagnostic Probe, Heated, Finger probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
SPACE GEAR (PA/B/D/V
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
SPACE GEAR (PA/B/D/V
(kvaliteediklass: Q)"

• Spanner Size: 13
• for OE number: 8342087703
• Manufacturer: KAMOKA

• Length [mm]: 59
• Housing Colour: black
• Spanner Size: 19
• Manufacturer: KAMOKA

• Switch Pressure [bar]: 0.3
• Thread Size: 1/8x28 BSPT
• Sensor Type: Closed-type Sensor
• Manufacturer: VERNET

• Fabrication Number: ECT-MS-000
• Manufacturer: NTY
• Name: NTY ECT-MS-000

• Pressure [bar]: 0.3
• Housing Colour: black
• Thread Size: 1/8
• Spanner Size: 24
• Number of pins: 1
• Manufacturer: DELPHI
• Name: DE SW90016
• Quality class: PJ

Additional information: "Tootja: DELPHI
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
(kvaliteediklass: PJ)"

• for OE number: MD 091056
• Number of pins: 1
• Weight [kg]: 0.02
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: 4G92 (SOHC 16V)
• Pressure [bar]: 0
• Thread Size: 1/8 GAS
• Spanner Size: 24
• Name: EP 1.800.094
• Manufacturer: EPS

• External Thread Size: 1/8" - 28
• Spanner Size: 13
• Number of connectors: 1
• Material: Brass
• Weight [kg]: 0.01
• Manufacturer: SWAG
• Name: SW 81 92 8265

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• External Thread Size: 1/8" - 28
• Spanner Size: 13
• Number of connectors: 1
• Material: Brass
• Weight [kg]: 0.01
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thread Size: 1/8x28 BSP
• Pressure [bar]: 0.4
• Manufacturer: FAE

• Number of pins: 1
• Switch pressure from [bar]: 0.2
• Switch pressure to [bar]: 0.4
• Thread Size: 1/8" BSPT
• Colour: black
• Supplementary Article/Supplementary Info: without gaskets/seals
• Manufacturer: METZGER

• Mounting Type: Bolted
• Voltage [V]: 12
• Pressure [bar]: 0.4
• Combi Switch Function: Normally Closed Contact
• Thread Size: 1/8 GAS
• Colour: red
• Spanner Size: 24
• Number of pins: 1
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6ZF007392001

• Construction Year to: 06.2003
• Manufacturer: BOSCH

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: rectangular
• Number of pins: 2
• Socket colour: black
• Spanner Size: 19
• Thread Size: 3/8
• for OE number: MD177572
• Manufacturer: NRF

• Connector Shape: oval
• Material: Plastic
• Number of pins: 2
• Plug Type: Female
• Sensor Type: NTC Sensor
• Spanner Size: S19
• Thread Size: PT3/8
• Name: NI 207007
• Manufacturer: NISSENS

Technical Information: FIRST FIT - a time-saving installation! Find all additional parts such as O-rings, clip, washer in the box.

• Fitting Position: Exhaust Side
• Transmission Type: 5-Speed Manual Transmission
• Fabrication Number: ECR-MS-001
• Manufacturer: NTY

• Thread Size: 3/8 x 19 BSP
• Colour: black
• Spanner Size: 19
• Number of pins: 2
• Weight [kg]: 0.042
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 3
• Supplementary Article/Info 2: without cable
• Connector Shape: oval
• Fabrication Number: ECP-MS-004
• Manufacturer: NTY

• Fabrication Number: ECP-HY-005
• Manufacturer: NTY

• Colour: black
• Number of pins: 2
• Weight [kg]: 0.3
• Packaging length [cm]: 12
• Packaging width [cm]: 8
• Packaging height [cm]: 6

• Housing Colour: black
• Number of pins: 2
• Thread Size: PT3/8
• Spanner Size: 19
• Manufacturer: DELPHI
• Name: DE TS10327

• Length [mm]: 59.7
• Spanner Size: 19
• Number of connectors: 2
• Colour: black
• Weight [kg]: 0.04
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Length [mm]: 59.7
• Spanner Size: 19
• Number of connectors: 2
• Colour: black
• Weight [kg]: 0.04
• Name: SW 80 93 2375
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Voltage [V]: 12
• Supplementary Article/Supplementary Info: without cable pull
• Number of pins: 3
• Weight [kg]: 0.03
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 17SKV243
• Manufacturer: ESEN SKV

• Engine Code: 4G92 (SOHC 16V)
• Thread Size: 3/8-GAS
• Spanner Size: 19
• Name: EP 1.830.230
• Manufacturer: EPS

• Number of connectors: 2
• Colour: black
• Weight [kg]: 0.066
• Manufacturer: BLUE PRINT

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Voltage [V]: 12
• Resistor [Ohm]: 2,080, 294
• Temperature range from [°C]: 25
• Temperature range to [°C]: 80
• Thread Size: 3/8 GAS
• Colour: black
• Spanner Size: 19
• Sensor Type: NTC Sensor
• Number of pins: 2
• Corresponds to the original part in colour: black
• Mounting Type: Vertical Screw Fitting
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 3
• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: without cable
• Housing Colour: black
• Manufacturer: BREMI

• Engine Code: 4G92 (SOHC 16V)
• Alternatively:
• Number of pins: 3
• Alternative Repair Kit: 550346
• Fitting Depth [mm]: 11
• Manufacturer: ERA

• Supplementary Article/Info 2: without cable
• Sensor Type: Hall Sensor
• Number of pins: 3
• Manufacturer: MEAT&DORIA

• Engine Code: 4G92
• Voltage [V]: 12
• Length [mm]: 360
• Number of pins: 3
• Weight [kg]: 0.07
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV329

• Length [mm]: 58
• Number of connectors: 3
• Weight [kg]: 0.03
• Manufacturer: BLUE PRINT
• Additional information: ADC47204
• Lisainfo: ADC47204

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Length [mm]: 57.5
• Number of connectors: 3
• Weight [kg]: 0.03
• Name: SW 90 93 2575
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

Manufacturer: MAGNETI MARELLI

• Length [mm]: 57.5
• Number of connectors: 3
• Weight [kg]: 0.03
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: 4G92 (SOHC 16V)
• Alternatively:
• Rotation Direction: Clockwise rotation
• Number of pins: 4
• Alternative Repair Kit: 550512
• Manufacturer: ERA

Manufacturer: MAGNETI MARELLI

• Number of pins: 3
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Alternatively:
• Number of pins: 3
• Fitting Depth [mm]: 27
• Alternative Repair Kit: 550329
• Resistor M[ohm]: 13
• Manufacturer: ERA

• Engine Code: 4G92 (SOHC 16V)
• Cable Length [mm]: 370
• Alternatively:
• Number of pins: 3
• Alternative Repair Kit: 550353
• Manufacturer: ERA

• Number of pins: 3
• Connector Shape: oval
• Supplementary Article/Info 2: without cable
• Manufacturer: MEAT&DORIA

• Lambda Sensor: Lambda Sensor, Thread pre-greased
• Fabrication Number: ESL-UV-001
• Manufacturer: NTY
• Name: NTY ESL-UV-001

• Lambda Sensor: Unheated
• Lisainfo: Lambda sensor
• Additional information: Lambda sensor

Number of pins: 3

• Engine Code: 4G92 (SOHC 16V)
• Name: EP 1.953.335
• Manufacturer: EPS

• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Fabrication Number: ESL-MS-003
• Manufacturer: NTY

Fitting Position: Front, before catalytic converter, after catalytic converter Lambda Sensor: Regulating Probe, Diagnostic Probe, Thread pre-greased

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Engine Code: 4G92 (SOHC 16V)
• Cable Length [mm]: 700
• Alternatively:
• Number of pins: 3
• Alternative Repair Kit: 550352
• Manufacturer: ERA

• Number of pins: 3
• Supplementary Article/Info 2: for camshaft, without cable
• Required quantity: 1
• Sensor Type: Hall Sensor
• Supplementary Article/Supplementary Info: with seal
• Number of connectors: 3
• Rated Voltage [V]: 12
• Fitting Depth [mm]: 27
• Housing Colour: black
• Connector Shape: oval
• Number of mounting bores: 1
• Weight [kg]: 0.02
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Lambda Sensor
• Weight [kg]: 0.12
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV121
• Manufacturer: ESEN SKV

• Engine Code: 4G92 (SOHC 16V)
• Cable Length [mm]: 350
• Alternatively:
• Number of pins: 2
• Fitting Depth [mm]: 12
• Alternative Repair Kit: 550334
• Manufacturer: ERA

• Lambda Sensor: Regulating Probe, Lambda Sensor
• Exhaust System: after catalytic converter
• Voltage [V]: 12
• Number of circuits: 4
• Weight [kg]: 0.09
• Resistor [Ohm]: 13
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV913
• Manufacturer: ESEN SKV

• Engine Code: 4G92 (SOHC 16V)
• Lambda Sensor: Regulating Probe
• Number of circuits: 4
• Supplementary Article/Info 2: without plug
• Manufacturer: ENERGY

• Lambda Sensor: Regulating Probe
• Number of pins: 4
• Cable Length [mm]: 630
• Manufacturer: MEAT&DORIA

• Quality: OE
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 103
• Gross Weight [g]: 147
• Manufacturer: DENSO
• Lisainfo: DOX-0109 DENSO
• Additional information: DOX-0109 DENSO

Lambda Sensor: Diagnostic Probe, Heated, Finger probe, Lambda Sensor

• Voltage [V]: 12
• Sensor Type: Hall Sensor
• Supplementary Article/Supplementary Info: with seal
• Number of pins: 3
• Number of mounting bores: 1
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead
• Name: HE 6PU009121801
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Number of pins: 3
• Voltage [V]: 12
• Connector Shape: oval
• Supplementary Article/Info 2: without cable
• Weight [kg]: 0.03
• Manufacturer: VALEO
• Name: VA 254119

• Lambda Sensor: Regulating Probe, Finger probe, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 340
• Manufacturer: DELPHI

• Lambda Sensor: Regulating Probe
• Engine Code: 4G92
• Voltage [V]: 12
• Length [mm]: 420
• Number of circuits: 4
• Weight [kg]: 0.9
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV024
• Manufacturer: ESEN SKV

• Construction Year to: 06.2003
• Lambda Sensor: Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Fitting Position: before catalytic converter
• Cable Length [mm]: 360
• Weight [kg]: 0.1
• Manufacturer: BLUE PRINT

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Construction Year to: 06.2003
• Lambda Sensor: Regulating Probe, Diagnostic Probe
• Block Separation:
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Manufacturer: BOSCH
• Name: BS 0258986507

Fitting Position: before catalytic converter, after catalytic converter

• Exhaust System: for pre-catalytic converter
• Quality: OE
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 95
• Gross Weight [g]: 144
• Manufacturer: DENSO
• Name: Lambda sensor
• Quality class: Q

Lambda Sensor: Regulating Probe, Heated, Finger probe, Lambda Sensor Additional information: "Tootja: DENSO
SPACE WAGON (N5/W),
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
SPACE WAGON (N5/W),
(kvaliteediklass: Q)"

• Lambda Sensor: Regulating Probe
• Voltage [V]: 12
• Length [mm]: 470
• Number of circuits: 4
• Weight [kg]: 0.12
• Resistor [Ohm]: 6
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: ESEN SKV

• Number of pins: 3
• Sensor Type: Hall Sensor
• Fitting Depth [mm]: 27
• Quality: OE
• Manufacturer: METZGER

• Lambda Sensor: Diagnostic Probe, Heated
• Fitting Position: after catalytic converter
• Cable Length [mm]: 410
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PA358103171

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Construction Year to: 06.2003
• Lambda Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 380
• Available as universal article as well, see article no.: 0258986507
• Recommended change interval [km]: 160,000
• Manufacturer: BOSCH

• Fitting Position: Front, after catalytic converter
• Lambda Sensor: Regulating Probe, Heated, Thread pre-greased
• Line insulation design: with silicone-coated woven-fibre insulation
• Socket colour: black
• Number of circuits: 4
• Number of pins: 4
• Connector Shape: angular
• Thread Size: M18 x 1,5
• Weight [kg]: 0.115
• for OE number: MD 177969
• Cable Length [mm]: 350
• Length [mm]: 470
• Number of connectors: 4
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Exhaust System: for pre-catalytic converter
• for OE number: 1588A020
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 390
• Number of pins: 4
• Weight [g]: 93
• Gross Weight [g]: 126
• Manufacturer: DENSO
• Name: DN DOX-0313
• Quality class: Q

Lambda Sensor: Regulating Probe, Heated, Finger probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
COLT V (CJ/A), 09.95
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
COLT V (CJ/A), 09.95
(kvaliteediklass: Q)"

• Engine Code: 4G92 (SOHC 16V)
• Cable Length [mm]: 700
• Number of pins: 3
• Manufacturer: ERA