• Engine Code: Z 16 XE, X 16 XEL
• Required quantity: 4
• for OE number: 1WT318110
• Connector type: Solid SAE
• Diameter [mm]: 14
• Spanner Size: 16
• Tightening Torque [Nm]: 22
• Weight [g]: 43
• Spark Plug: 1 - Earthed Electrode, Nickel Middle Electrode
• Thread Length [mm]: 19
• Gross Weight [g]: 46
• Manufacturer: DENSO
• Name: DN K20TT
• Lisainfo: K20TT DENSO
• Additional information: K20TT DENSO

• Engine Code: X 16 XEL, Z 16 XE
• Spark Plug: 1 - Earthed Electrode, with resistor
• Electrode Gap [mm]: 0.9
• Thread Size: M14 x 1.25
• Thread Length [mm]: 19
• Spanner Size: 16
• Technical Information: Nichel-Chromium with internal in branch
• Manufacturer: MAGNETI MARELLI

• Block Separation:
• Spark Plug: 1 - Earthed Electrode
• Supplementary Article/Info 2: Do not fit parts from different manufacturers!
• Manufacturer: TOPRAN

Vehicle Identification Number (VIN) from: 4B000001, 4G000001, 4H000001, 42000001, 45000001, 48000001 General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Fuel Type: CNG/LPG
• Supplementary Article/Info 2: Electrode gap must be set for operation on gas
• Replace after km: 15,000
• Electrode Gap [mm]: 0.7
• Length [mm]: 126
• Weight [kg]: 0.06
• Spark Plug: 1 - Earthed Electrode
• Version: E7EC1
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Spark Plug: 2 - Earthed Electrode
• Electrode Gap [mm]: 1
• Supplementary Article/Info 2: Do not fit parts from different manufacturers!
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Fuel Type: CNG/LPG
• Supplementary Article/Info 2: Electrode gap must be set for operation on gas
• Replace after km: 15,000
• Electrode Gap [mm]: 0.7
• Length [mm]: 126
• Height [mm]: 51
• Weight [kg]: 0.062
• Spark Plug: 1 - Earthed Electrode
• Version: VR7EC1
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Spark Plug: Nickel Middle Electrode, 2 - Earthed Electrode
• Thread Length [mm]: 19
• Spanner Size: 16 mm
• for OE number: 9618494580
• Manufacturer: KAMOKA

• Fuel Type: CNG/LPG
• Supplementary Article/Info 2: Electrode gap must be set for operation on gas
• Replace after km: 15,000
• Required quantity: 4
• Electrode Gap [mm]: 0.9
• Tightening Torque [Nm]: 28
• Thread Size: M 14 x 1,25
• Thread Length [mm]: 19
• Spanner Size: 16
• Spark Position [mm]: 3
• Number of pins: 1
• Name: SššTEKššNAL
• Manufacturer: BOS

• Tightening torque from [Nm]: 20
• Tightening torque to [Nm]: 40
• Tightening Torque [Nm]: 30
• Electrode Gap [mm]: 0.9
• Thread Size: M14 x 1.25
• Spanner Size: 16
• Spark Plug: 1 - Earthed Electrode
• Thread Length [mm]: 19
• Assy./disassy. by qualified personnel required!:
• Name: HE 8EH188704381
• Manufacturer: HELLA

• External Thread Size: M14 x 1,25
• Thread Length [mm]: 19
• Spanner Size: 16
• Electrode Gap [mm]: 1
• Spark Plug: with gasket seat, 2 - Earthed Electrode
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Required quantity: 4
• Electrode Gap [mm]: 1
• Tightening Torque [Nm]: 28
• Thread Size: M 14 x 1,25
• Thread Length [mm]: 19
• Spanner Size: 16
• Spark Position [mm]: 6
• Number of pins: 2
• Name: SššTEKššNAL
• Manufacturer: BOS

• Electrode Gap [mm]: 1
• Spark Plug: 2 - Earthed Electrode
• Weight [kg]: 0.046
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Required quantity: 4
• Alternatively:
• Electrode Gap [mm]: 0.9
• Connector type: SAE
• Thread Size: M14x1,25
• Spanner Size: 16 mm
• Quality/ Grade: Poly-V Tit
• Spark Plug: 1 - Earthed Electrode, with gasket seat
• Thread Length [mm]: 19
• Tightening torque from [Nm]: 25
• Tightening torque to [Nm]: 30
• Resistor from [kOhm]: 3
• Resistor to [kOhm]: 10
• Name: SššTEKššNAL
• Manufacturer: BERU

• Engine Code: Z 16 XE, X 16 XEL
• Required quantity: 4
• for OE number: 7700500168
• Connector type: Removable SAE
• Diameter [mm]: 14
• Spanner Size: 16
• Tightening Torque [Nm]: 22
• Weight [g]: 43
• Spark Plug: 2 - Earthed Electrode, Nickel Middle Electrode
• Thread Length [mm]: 19
• Gross Weight [g]: 46
• Manufacturer: DENSO
• Name: DN K20TXR
• Lisainfo: K20TXR DENSO
• Additional information: K20TXR DENSO

• Engine Code: X 16 XEL, Z 16 XE
• Spanner Size: 16 mm
• Thread Size: M14 x 1,25
• Thread Length [mm]: 19
• Spark Position [mm]: 6
• Name: SššTEKššNAL
• Manufacturer: NGK
• Additional information: BKR5EK
• Lisainfo: BKR5EK

Spark Plug: Nickel Middle Electrode, 2 - Earthed Electrode, Interference Suppression 5 kOhm, with gasket seat, Fixed SAE connector

• Engine Code: X 16 XEL, Z 16 XE
• Spanner Size: 16 mm
• Thread Size: M14 x 1,25
• Thread Length [mm]: 19
• Spark Position [mm]: 6
• Name: SššTEKššNAL
• Manufacturer: NGK

Spark Plug: Nickel Middle Electrode, 2 - Earthed Electrode, Interference Suppression 5 kOhm, with gasket seat, Fixed SAE connector

• Required quantity: 4
• Electrode Gap [mm]: 1
• Connector type: M4/SAE
• Thread Size: M14x1.25
• Spanner Size: 16 mm
• Quality/ Grade: Nickel GE
• Packing Type: Box
• Thread Length [mm]: 19
• Technical Information Number: RC10DMC
• Spark Position [mm]: 6.1
• Tightening torque from [Nm]: 25
• Tightening torque to [Nm]: 30
• Packaging length [cm]: 8.85
• Packaging width [cm]: 2.6
• Packaging height [cm]: 2.35
• Resistor from [kOhm]: 3
• Resistor to [kOhm]: 9
• Projection [mm]: 3.6
• Name: CH OE019/T10
• Manufacturer: CHAMPION

Spark Plug: 2 - Earthed Electrode, with gasket seat, Copper Centre Electrode

• Tightening Torque [Nm]: 25
• Electrode Gap [mm]: 1
• Thread Size: M14 x 1.25
• Spanner Size: 16
• Spark Plug: 1 - Earthed Electrode
• Thread Length [mm]: 19
• Assy./disassy. by qualified personnel required!:
• Name: HE 8EH188705041
• Manufacturer: HELLA

• Required quantity: 4
• Electrode Gap [mm]: 0.9
• Connector type: SAE
• Thread Size: M14x1.25
• Spanner Size: 16 mm
• Quality/ Grade: Cu-core GE
• Packing Type: Box
• Thread Length [mm]: 19
• Technical Information Number: RC10MCC
• Spark Position [mm]: 5
• Tightening torque from [Nm]: 25
• Tightening torque to [Nm]: 30
• Packaging length [cm]: 8.65
• Packaging width [cm]: 2.45
• Packaging height [cm]: 2.45
• Resistor from [kOhm]: 3
• Resistor to [kOhm]: 7.5
• Projection [mm]: 3.4
• Name: CH OE198/T10
• Manufacturer: CHAMPION

Spark Plug: 1 - Earthed Electrode, with gasket seat, Copper Centre Electrode

• Required quantity: 4
• Electrode Gap [mm]: 1
• Connector type: SAE
• Thread Size: M14x1,25
• Spanner Size: 16 mm
• Spark Plug: 2 - Earthed Electrode, with gasket seat
• Thread Length [mm]: 19
• Technical Information Number: 14 FR-8 LDUOX4
• Tightening torque from [Nm]: 25
• Tightening torque to [Nm]: 30
• Name: SššTEKššNAL
• Manufacturer: BERU

• Engine Code: X 16 XEL, Z 16 XE
• Spark Plug: 1 - Earthed Electrode, with resistor
• Electrode Gap [mm]: 0.9
• Thread Size: M14 x 1.25
• Thread Length [mm]: 19
• Spanner Size: 16
• Technical Information: Platinum-tip
• Name: MM SPB7206-9
• Manufacturer: MAGNETI MARELLI

• Required quantity: 4
• Electrode Gap [mm]: 0.9
• Connector type: M4/SAE
• Thread Size: M14x1,25
• Spanner Size: 16 mm
• Spark Plug: 1 - Earthed Electrode, with gasket seat
• Thread Length [mm]: 19
• Technical Information Number: 14 FR-8 LU2
• Self-service suited packaging see parts list:
• Tightening torque from [Nm]: 25
• Tightening torque to [Nm]: 30
• Name: SššTEKššNAL
• Manufacturer: BERU

• Supplementary Article/Info 2: Mostly short distance travel
• Required quantity: 4
• Electrode Gap [mm]: 1.35
• Tightening Torque [Nm]: 28
• Thread Size: M 14 x 1,25
• Thread Length [mm]: 19
• Spanner Size: 16
• Spark Position [mm]: 5
• Number of pins: 4
• Name: SššTEKššNAL
• Manufacturer: BOS

• Fuel Type: CNG/LPG
• Replace after km: 30,000
• Electrode Gap [mm]: 1.1
• External Thread [mm]: M14
• Spanner Size: 16 [mm]
• Number of pins: 1
• Thread Length [mm]: 19
• Thread Pitch [mm]: 1.25
• Weight [kg]: 0.045
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fuel Type: CNG/LPG
• Replace after km: 30,000
• Required quantity: 4
• Electrode Gap [mm]: 0.7
• Tightening Torque [Nm]: 28
• Thread Size: M 14 x 1,25
• Thread Length [mm]: 19
• Spanner Size: 16
• Spark Position [mm]: 4
• Number of pins: 1
• Name: SššTEKššNAL
• Manufacturer: BOS

• Required quantity: 4
• Alternatively:
• Electrode Gap [mm]: 0.8
• Connector type: SAE
• Thread Size: M14x1.25
• Spanner Size: 16 mm
• Quality/ Grade: Pt GE
• Packing Type: Box
• Thread Length [mm]: 19
• Technical Information Number: RC10WMPB3
• Spark Position [mm]: 5
• Tightening torque from [Nm]: 25
• Tightening torque to [Nm]: 30
• Packaging length [cm]: 9.5
• Packaging width [cm]: 2.4
• Packaging height [cm]: 2.4
• Resistor from [kOhm]: 3
• Resistor to [kOhm]: 10
• Projection [mm]: 3
• Name: CH CCH9013
• Manufacturer: CHAMPION

Spark Plug: 1 - Earthed Electrode, with gasket seat, Iridium Middle Electrode

• Engine Code: Z 16 XE, X 16 XEL
• Required quantity: 4
• Fuel Type: CNG/LPG
• Connector type: Solid SAE
• Diameter [mm]: 14
• Spanner Size: 16
• Tightening Torque [Nm]: 22
• Weight [g]: 43
• Country Specific Design: Japan
• Spark Plug: 1 - Earthed Electrode, Platinum Middle Electrode
• Thread Length [mm]: 19
• Gross Weight [g]: 46
• Manufacturer: DENSO
• Name: DN IK20TT
• Lisainfo: IK20TT DENSO
• Additional information: IK20TT DENSO

• Engine Code: X 16 XEL, Z 16 XE
• Spanner Size: 16 mm
• Thread Size: M14 x 1,25
• Thread Length [mm]: 19
• Spark Position [mm]: 3.5
• Manufacturer: NGK

Spark Plug: Iridium Middle Electrode, 1 - Earthed Electrode, Interference Suppression 5 kOhm, with gasket seat, Fixed SAE connector

• Required quantity: 4
• Fuel Type: Liquefied Petroleum Gas (LPG)
• Alternatively:
• Recommended change interval [km]: 30,000
• Electrode Gap [mm]: 0.7
• Connector type: SAE
• Thread Size: M14x1,25
• Spanner Size: 16 mm
• Spark Plug: 1 - Earthed Electrode, with gasket seat
• Thread Length [mm]: 19
• Technical Information Number: 14 FR-7 DPPUS2
• Self-service suited packaging see parts list:
• Tightening torque from [Nm]: 25
• Tightening torque to [Nm]: 30
• Name: SššTEKššNAL
• Manufacturer: BERU

• Engine Code: X 16 XEL, Z 16 XE
• Spanner Size: 16 mm
• Thread Size: M14 x 1,25
• Spark Plug: Iridium Middle Electrode, Fixed SAE connector
• Fuel Type: CNG/LPG
• Recommended change interval [km]: 60,000
• Name: SššTEKššNAL
• Manufacturer: NGK
• Lisainfo: LPG1
• Additional information: LPG1