• Length [mm]: 180
• Cable Length [mm]: 460
• Fabrication Number: ESL-PL-012
• Manufacturer: NTY

Fitting Position: Front, before catalytic converter, after catalytic converter Lambda Sensor: Regulating Probe, Diagnostic Probe, Thread pre-greased

• Lambda Sensor: Lambda Sensor, Thread pre-greased
• Fabrication Number: ESL-UV-001
• Manufacturer: NTY
• Name: NTY ESL-UV-001

• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Fitting Position: after catalytic converter
• Number of pins: 4
• Lambda Sensor: Diagnostic Probe
• Total Length [mm]: 315
• Manufacturer: JP GROUP
• Lisainfo: Lambda sensor
• Additional information: Lambda sensor

• Fitting Position: before catalytic converter
• Lambda Sensor: Regulating Probe
• Manufacturer: DELLO AUTOMEGA

• Engine Code: Z 16 XE
• Construction Year to: 09.2005
• Lambda Sensor: Diagnostic Probe, Heated
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 314
• Thread Size: M18x1,5
• Spanner Size: 22
• for OE number: 93189975
• Manufacturer: DELLO AUTOMEGA

• Engine Code: Z 16 XE
• Construction Year to: 09.2005
• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Fitting Position: after catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 350
• Number of connectors: 4
• Weight [kg]: 0.126
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Regulating Probe, Diagnostic Probe, Lambda Sensor
• Block Separation:
• Engine Code: Z 16 XE
• Cable Length [mm]: 520
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV132

Fitting Position: before catalytic converter, after catalytic converter

• Engine Code: Z 16 XE
• Construction Year to: 09.2005
• Lambda Sensor: Regulating Probe, Heated
• Fitting Position: before catalytic converter
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Lambda Sensor: Lambda Sensor
• Weight [kg]: 0.12
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV121
• Manufacturer: ESEN SKV

• Fitting Position: before catalytic converter
• Lambda Sensor: Regulating Probe, Planar probe
• Number of pins: 4
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Engine Code: Z 16 XE
• Lambda Sensor: Regulating Probe
• Number of circuits: 4
• Supplementary Article/Info 2: without plug
• Manufacturer: ENERGY

• Lambda Sensor: Regulating Probe, Finger probe
• Fitting Position: before catalytic converter
• Engine Number from: 20HH5428
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Transmission Type: Manual Transmission
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Lambda Sensor: Diagnostic Probe, Planar probe
• Fitting Position: after catalytic converter
• Number of pins: 4
• Length [mm]: 335
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Lambda Sensor: Diagnostic Probe, Planar probe
• Fitting Position: after catalytic converter
• Number of pins: 4
• Length [mm]: 315
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Lambda Sensor: Regulating Probe, Thread pre-greased
• Fitting Position: Exhaust Manifold
• Line insulation design: with silicone-coated woven-fibre insulation
• Cable Length [mm]: 650
• Weight [kg]: 0.126
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 05.2006
• Exhaust System: for pre-catalytic converter
• Cable Length [mm]: 370
• Lambda Sensor: Planar probe, Heated
• Name: LAMBDA ANDUR
• Manufacturer: DLP

• Lambda Sensor: Diagnostic Probe, Lambda Sensor
• Engine Code: Z 16 XE
• Voltage [V]: 12
• Length [mm]: 290
• Number of circuits: 4
• Weight [kg]: 0.09
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV073
• Manufacturer: ESEN SKV

• Lambda Sensor: Regulating Probe
• Engine Code: Z 16 XE
• Voltage [V]: 12
• Length [mm]: 770
• Number of circuits: 4
• Weight [kg]: 0.11
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV074

• Block Separation:
• Cable Length [mm]: 520
• Manufacturer: DELPHI
• Name: DE ES20291-12B1

Lambda Sensor: Diagnostic Probe, Regulating Probe, Planar probe, Heated Fitting Position: after catalytic converter, before catalytic converter

• Lambda Sensor: Lambda Sensor
• Voltage [V]: 12
• Length [mm]: 350
• Number of circuits: 4
• Weight [kg]: 0.14
• Resistor [Ohm]: 3.5
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV674

• Lambda Sensor: Diagnostic Probe, Planar probe, Heated
• Engine Code: Z 16 XE
• Cable Length [mm]: 300
• Name: LAMBDA ANDUR
• Manufacturer: DLP
• Quality class: PJ

Additional information: "Tootja: DELPHI
MERIVA, 05.03-05.10
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
MERIVA, 05.03-05.10
(kvaliteediklass: PJ)"

• Number of pins: 4
• Lambda Sensor: Planar probe
• Voltage [V]: 12
• Overall Length [mm]: 500
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Exhaust System: for pre-catalytic converter
• Quality: OE
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 103
• Gross Weight [g]: 147
• Manufacturer: DENSO
• Name: Lambda sensor
• Quality class: Q

Lambda Sensor: Regulating Probe, Heated, Finger probe, Lambda Sensor Additional information: "Tootja: DENSO
SCORPIO I SEDAN (GGE
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
SCORPIO I SEDAN (GGE
(kvaliteediklass: Q)"

• Lambda Sensor: Regulating Probe
• Voltage [V]: 12
• Length [mm]: 780
• Number of circuits: 4
• Weight [kg]: 0.14
• Resistor [Ohm]: 6
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV685

• Engine Code: Z 16 XE
• Fitting Position: before catalytic converter
• Length [mm]: 390
• Cable Length [mm]: 570
• Conductor Number: 4
• Available as universal article as well, see article no.: 1.997.007
• Number of circuits: 4
• Name: EP 1.997.089
• Manufacturer: EPS

Lambda Sensor: Regulating Probe, Heated, Planar probe, Thread pre-greased

• Engine Code: Z 16 XE
• Construction Year to: 09.2005
• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Engine Code: Z 16 XE
• Fitting Position: after catalytic converter
• Length [mm]: 180
• Cable Length [mm]: 300
• Conductor Number: 4
• Available as universal article as well, see article no.: 1.997.007
• Number of circuits: 4
• Name: LAMBDA ANDUR
• Manufacturer: EPS

Lambda Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased

• Engine Code: Z 16 XE
• Construction Year to: 09.2005
• Lambda Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• for OE number: 855523, 855353
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 775
• Number of pins: 4
• Weight [g]: 119
• Gross Weight [g]: 149
• Manufacturer: DENSO

Lambda Sensor: Regulating Probe, Heated, Finger probe, Lambda Sensor

• Fitting Position: Front, before catalytic converter
• Lambda Sensor: Regulating Probe
• Length [mm]: 630
• Number of pins: 4
• Technical Information Number: Universal 77004
• Manufacturer: FAE

• Engine Code: Z 16 XEP
• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Engine Number from: 20HH5428
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Fitting Position: Rear
• Lambda Sensor: Diagnostic Probe
• Length [mm]: 350
• Number of pins: 4
• Technical Information Number: Universal 77004
• Manufacturer: FAE

• Line insulation design: with silicone-coated woven-fibre insulation
• Thread Size: M18x1,5mm
• Overall Length [mm]: 300
• Cable Length [mm]: 300
• Number of pins: 4
• Weight [kg]: 0.104
• Lambda Sensor: Thread pre-greased
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• for OE number: 855524
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 290
• Number of pins: 4
• Weight [g]: 90
• Gross Weight [g]: 120
• Manufacturer: DENSO

Lambda Sensor: Diagnostic Probe, Heated, Finger probe, Lambda Sensor

• Fitting Position: before catalytic converter
• Lambda Sensor: Regulating Probe
• Cable Length [mm]: 630
• Number of pins: 4
• Exhaust System: before catalytic converter
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PA358066001
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Engine Code: Z 16 XE
• Construction Year to: 09.2005
• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Engine Code: Z 16 XE
• Lambda Sensor: Diagnostic Probe, Heated
• Voltage [V]: 12
• Conductor Number: 4
• Cable Length [mm]: 350
• Manufacturer: PIERBURG

• Engine Code: Z 16 XE
• Construction Year to: 09.2005
• Lambda Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 314
• Name: LAMBDA ANDUR
• Manufacturer: BOS