• Vehicle Identification Number (VIN) from: 6K-X-610 001
• Fitting Position: Front Axle Left, Front Axle Right
• Manufacturer: JP GROUP
• Lisainfo: Protective Cap/Bellow, shock absorber
• Additional information: Protective Cap/Bellow, shock absorber

• Fitting Position: Front Axle
• Shock Absorber Type: Oil Pressure
• Shock Absorber Design: Suspension Strut
• Shock Absorber System: Twin-Tube
• Shock Absorber Mounting Type: Top pin, Bottom Clamp
• Weight [kg]: 3.9
• Bore Ø [mm]: 27
• Piston Rod Diameter [mm]: 20
• Article number of recommended accessories: MK067, PK001
• Packaging length [cm]: 51.5
• Packaging width [cm]: 16.2
• Packaging height [cm]: 16.2
• Manufacturer: MONROE
• Lisainfo: 11250 MON
• Additional information: 11250 MON

Warranty: 5 years warranty with accessories when replaced in pairs

• Fitting Position: Rear Axle
• Height [mm]: 104
• Material: Rubber
• Inner Diameter [mm]: 43
• Manufacturer: MAX

Name: Kaitsekaan/kaitsekumm - Vedrustus/amordid VW T. POLO 94-

• for OE number: 6N0513425A
• Fitting Position: Rear Axle
• Material: Plastic
• Weight [g]: 31
• Name: IM 37454
• Manufacturer: ORIGINAL IMPERIUM

• Vehicle Identification Number (VIN) from: 6K-X-610 001
• Fitting Position: Front Axle both sides
• Length [mm]: 205
• Weight [kg]: 0.065
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• for OE number: 1H0413175
• Fitting Position: Front Axle
• Height [mm]: 225
• Material: Thermoplast
• Weight [g]: 102
• Diameter 1 [mm]: 21
• Diameter 2 [mm]: 75
• Manufacturer: IMPERGOM

• Vehicle Identification Number (VIN) from: 6K-X-610 001
• Outer Diameter [mm]: 68, 80
• Material: Thermoplast
• Fitting Position: Front Axle
• Weight [kg]: 0.07
• Name: Kaitsemts/kaitsekumm,amort
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Vehicle Identification Number (VIN) to: 6K-X-610 000
• Thickness [mm]: 228.5
• Material: Thermoplast
• Fitting Position: Front Axle
• Weight [kg]: 0.064
• for OE number: 1H0 413 175
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Vehicle Identification Number (VIN) from: 6K-X-610 001
• Outer Diameter [mm]: 68, 80
• Material: Thermoplast
• Fitting Position: Front Axle
• Weight [kg]: 0.07
• Name: SW 30 93 6006
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Front Axle
• Weight [kg]: 0.108
• Packaging length [cm]: 19
• Packaging width [cm]: 7.8
• Packaging height [cm]: 7.8
• Manufacturer: FEBEST

• Fitting Position: Rear Axle
• Suspension: for vehicles with bad road version
• Shock Absorber Design: Telescopic Shock Absorber
• Shock Absorber Mounting Type: Top pin, Bottom eye
• Shock Absorber Type: Gas Pressure
• Shock Absorber System: Twin-Tube
• Manufacturer: ABAKUS DEPO/LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis.

• Fitting Position: Rear Axle
• Supplementary Article/Supplementary Info: without spring seat
• Shock Absorber Type: Gas Pressure
• Shock Absorber Mounting Type: Bottom eye, Top pin
• Shock Absorber System: Twin-Tube
• Shock Absorber Design: Suspension Strut
• Manufacturer: KAMOKA AMORTYZATORY

• Fitting Position: Rear Axle
• Supplementary Article/Supplementary Info: without spring seat
• Shock Absorber Type: Oil Pressure
• Shock Absorber Mounting Type: Bottom eye, Top pin
• Shock Absorber Design: Suspension Strut
• Manufacturer: KAMOKA AMORTYZATORY

• Fitting Position: Rear Axle
• Shock Absorber Type: Gas Pressure
• Shock Absorber Mounting Type: Bottom eye, Top pin
• Shock Absorber System: Twin-Tube
• Thread Size: M10x1
• Piston Rod Length [mm]: 275
• Piston Rod Diameter [mm]: 12.5
• Suspension Strut Outer Diameter [mm]: 38
• Manufacturer: OPTIMAL ZAWIESZENIE

Shock Absorber Design: Suspension Strut Insert, Suspension Strut, Spring-bearing Damper

• Name: shock absorber
• Quality class: PJ

Lisainfo: "Tootja: SRL
SEAT IBIZA/CORDOBA
(kvaliteediklass: PJ)"

• Fitting Position: Rear Axle
• Supplementary Article/Supplementary Info: without spring seat
• Shock Absorber Type: Oil Pressure
• Shock Absorber Mounting Type: Bottom eye, Top pin
• Shock Absorber Design: Suspension Strut
• Manufacturer: KAMOKA AMORTYZATORY

• Fitting Position: Rear Axle
• Shock Absorber System: Twin-Tube
• Shock Absorber Type: Gas Pressure
• Shock Absorber Mounting Type: Top pin, Bottom eye
• Supplementary Article/Supplementary Info: without spring seat
• Article number of recommended accessories: SMJ0242
• Shock Absorber Design: Telescopic Shock Absorber
• Manufacturer: JAPKO

• Fitting Position: Front Axle
• Suspension: for vehicles with standard suspension
• Shock Absorber Type: Gas Pressure
• Shock Absorber Design: Suspension Strut
• Shock Absorber System: Twin-Tube
• Shock Absorber Mounting Type: Top pin
• Manufacturer: ABAKUS DEPO/LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis.

• Fitting Position: Rear Axle
• Suspension: for vehicles with standard suspension
• Shock Absorber Design: Telescopic Shock Absorber
• Shock Absorber Mounting Type: Top pin, Bottom eye
• Shock Absorber Type: Gas Pressure
• Shock Absorber System: Twin-Tube
• Name: AMORT
• Manufacturer: MAX
• Lisainfo: MGA-5629
• Additional information: MGA-5629

• Fitting Position: Front Axle
• Shock Absorber Type: Gas Pressure
• Shock Absorber Design: Suspension Strut
• Shock Absorber Mounting Type: Top pin
• Shock Absorber System: Twin-Tube
• Article number of recommended accessories: 72-1203, 72-1197
• Name: AMORT
• Manufacturer: MAX
• Lisainfo: MGA-2041
• Additional information: MGA-2041

• Fitting Position: Front Axle
• Shock Absorber Type: Oil Pressure
• Shock Absorber Mounting Type: Top pin
• Shock Absorber Design: Suspension Strut
• Manufacturer: KAMOKA AMORTYZATORY

• Fitting Position: Front Axle
• Shock Absorber Type: Oil Pressure
• Shock Absorber Design: Suspension Strut
• Shock Absorber Mounting Type: Top pin
• Name: CFD 424786
• Manufacturer: DACO

• Fitting Position: Rear Axle, Rear Axle Right, Rear Axle Left
• Shock Absorber Type: Oil Pressure
• Shock Absorber System: Twin-Tube
• Article number of recommended accessories: GH-694705
• Shock Absorber Design: Spring-bearing Damper
• Shock Absorber Mounting Type: Bottom eye, Top pin
• Manufacturer: AUTO-GH

• Fitting Position: Front Axle
• Suspension: for vehicles with standard suspension
• Shock Absorber Type: Oil Pressure
• Shock Absorber Design: Suspension Strut
• Shock Absorber System: Twin-Tube
• Shock Absorber Mounting Type: Bottom Pin
• Manufacturer: DENCKERMANN AMORTYZATORY

• Fitting Position: Front Axle
• Shock Absorber Type: Gas Pressure
• Shock Absorber Design: Suspension Strut
• Shock Absorber System: Twin-Tube
• Shock Absorber Mounting Type: Top pin
• Name: CFD 454786
• Manufacturer: DACO

• Suspension: for vehicles with sports suspension
• Vehicle Identification Number (VIN) to: 6K-Y-504 288
• Fitting Position: Front Axle
• Shock Absorber Type: Gas Pressure
• Shock Absorber System: Twin-Tube
• Shock Absorber Design: Suspension Strut
• Shock Absorber Mounting Type: Top pin
• Manufacturer: JP GROUP
• Lisainfo: Shock Absorber
• Additional information: Shock Absorber

• Shock Absorber Type: Gas Pressure
• Fitting Position: Front Axle
• Shock Absorber Design: Suspension Strut
• Shock Absorber Mounting Type: Top pin, Bottom Clamp
• Shock Absorber System: Twin-Tube
• Name: Gas shock absorber
• Quality class: PJ

Lisainfo: "Tootja: SRL
VW GOLF III 94-
(kvaliteediklass: PJ)" Additional information: "Tootja: SRL
VW GOLF III 94-
(kvaliteediklass: PJ)"

• Fitting Position: Front Axle
• Shock Absorber Type: Gas Pressure
• Shock Absorber Mounting Type: Top pin
• Shock Absorber System: Twin-Tube
• Shock Absorber Design: Suspension Strut
• Manufacturer: KAMOKA AMORTYZATORY
• Lisainfo: 2000198 KAMOKA
• Additional information: 2000198 KAMOKA

• Fitting Position: Front Axle
• Suspension: for vehicles with standard suspension
• Shock Absorber Type: Gas Pressure
• Shock Absorber Design: Suspension Strut
• Shock Absorber System: Twin-Tube
• Shock Absorber Mounting Type: Bottom Pin
• Manufacturer: DENCKERMANN AMORTYZATORY

• Suspension: for vehicles with sports suspension
• Shock Absorber Type: Gas Pressure
• Shock Absorber Design: Suspension Strut
• Fitting Position: Front Axle
• Shock Absorber Mounting Type: Top pin
• Shock Absorber System: Twin-Tube
• Name: AMORT
• Manufacturer: MAX

• Fitting Position: Rear Axle
• Shock Absorber Type: Gas Pressure
• Shock Absorber System: Twin-Tube
• Shock Absorber Design: Spring-bearing Damper
• Shock Absorber Mounting Type: Top pin, Bottom eye
• Article number of recommended accessories: 100 740 0006, 100 512 0007, 100 512 0008
• replacement in pairs recommended:
• Name: AMORT
• Manufacturer: MEY

• Fitting Position: Front Axle
• Shock Absorber Type: Oil Pressure
• Shock Absorber Design: Suspension Strut
• Shock Absorber System: Twin-Tube
• Shock Absorber Mounting Type: Top pin
• Diameter [mm]: 50
• Length 1 [mm]: 520
• Length 2 [mm]: 353
• Piston Rod Diameter [mm]: 20
• Quantity per axle: 1
• Observe technical data:
• Manufacturer: TRW

SVHC: No information available, please contact the manufacturer!

• Fitting Position: Front Axle
• Shock Absorber System: Twin-Tube
• Shock Absorber Type: Gas Pressure
• Shock Absorber Design: Suspension Strut
• Article number of recommended accessories: SMJ0133, SMJ0143, SMJ0145, SMJ0168
• Shock Absorber Mounting Type: Top pin
• Manufacturer: JAPKO

• Fitting Position: Rear Axle
• Shock Absorber Type: Oil Pressure
• Shock Absorber Mounting Type: Top pin, Bottom eye
• Supplementary Article/Supplementary Info: with spring seat
• Shock Absorber Design: Spring-bearing Damper
• Name: AMORT
• Manufacturer: KYB

• Fitting Position: Rear Axle
• Shock Absorber Type: Oil Pressure
• Shock Absorber Mounting Type: Top pin, Bottom eye
• Supplementary Article/Supplementary Info: without spring seat
• Shock Absorber Design: Telescopic Shock Absorber
• Manufacturer: KYB
• Name: KY 443296

Technical Information: SG-701 is available to replace the old spring seat if damage d or unable to be reused.

• Fitting Position: Front Axle
• Shock Absorber Type: Oil Pressure
• Shock Absorber Design: Suspension Strut
• Article number of recommended accessories: SMJ0133, SMJ0143, SMJ0145, SMJ0168
• Shock Absorber Mounting Type: Top pin
• Manufacturer: JAPKO

• Fitting Position: Front Axle
• Shock Absorber Design: Suspension Strut
• Shock Absorber Mounting Type: Top pin
• Shock Absorber Type: Oil Pressure
• Shock Absorber System: Twin-Tube
• Spring Type: for vehicles with coil spring suspension
• Manufacturer: MAGNETI MARELLI

• Fitting Position: Front Axle
• Shock Absorber Type: Gas Pressure
• Shock Absorber Design: Suspension Strut
• Shock Absorber System: Twin-Tube
• Shock Absorber Mounting Type: Top pin
• Diameter [mm]: 50
• Length 1 [mm]: 520
• Length 2 [mm]: 353
• Piston Rod Diameter [mm]: 20
• Quantity per axle: 1
• Observe technical data:
• Manufacturer: TRW

SVHC: No information available, please contact the manufacturer!

• Fitting Position: Front Axle
• Shock Absorber Type: Gas Pressure
• Shock Absorber System: Twin-Tube
• Shock Absorber Design: Suspension Strut
• Shock Absorber Mounting Type: Top pin
• replacement in pairs recommended:
• Name: Amort
• Manufacturer: MEY

Article number of recommended accessories: 100 412 0003, 100 412 9020/S, 100 412 0003/S, 100 412 1020/S, 100 640 0010

• Name: Gas shock absorber left, right
• Quality class: PJ

Lisainfo: "Tootja: MAGNETI MARELLI
VW POLO H/B, 10.94-
(kvaliteediklass: Q)"

• Fitting Position: Front Axle
• Shock Absorber Type: Oil Pressure
• Shock Absorber Design: Suspension Strut
• Shock Absorber Mounting Type: Top pin
• Name: Amort
• Manufacturer: KYB

• Fitting Position: Front Axle
• Shock Absorber Type: Oil Pressure
• Shock Absorber Design: Suspension Strut
• Shock Absorber Mounting Type: Top pin
• Manufacturer: KAYABA

• Fitting Position: Front Axle, Front Axle Right, Front Axle Left
• Shock Absorber Type: Oil Pressure
• Shock Absorber System: Twin-Tube
• Article number of recommended accessories: GH-694701
• Shock Absorber Design: Telescopic Shock Absorber
• Shock Absorber Mounting Type: Top pin
• Manufacturer: AUTO-GH

• Fitting Position: Front Axle, Front Axle Right, Front Axle Left
• Shock Absorber Type: Gas Pressure
• Shock Absorber System: Twin-Tube
• Article number of recommended accessories: GH-694701
• Shock Absorber Design: Telescopic Shock Absorber
• Shock Absorber Mounting Type: Top pin
• Manufacturer: AUTO-GH

• Fitting Position: Rear Axle
• Shock Absorber System: Twin-Tube
• Shock Absorber Type: Gas Pressure
• Shock Absorber Mounting Type: Top pin, Bottom eye
• Supplementary Article/Supplementary Info: without spring seat
• Shock Absorber Design: Telescopic Shock Absorber
• Manufacturer: KAYABA AMORTYZATORY

Technical Information: SG-701 is available to replace the old spring seat if damage d or unable to be reused.

• Fitting Position: Rear Axle
• Suspension: for vehicles with standard suspension
• Shock Absorber Design: Telescopic Shock Absorber
• Shock Absorber Mounting Type: Top pin, Bottom eye
• Shock Absorber Type: Gas Pressure
• Shock Absorber System: Twin-Tube
• Parameter: SEOV27X171A
• Name: AMORT
• Manufacturer: SAA

SVHC: No information available, please contact the manufacturer!

• Fitting Position: Front Axle
• Shock Absorber System: Twin-Tube
• Shock Absorber Type: Gas Pressure
• Shock Absorber Design: Suspension Strut
• Shock Absorber Mounting Type: Top pin
• Name: AMORT
• Manufacturer: KYB

• Fitting Position: Front Axle
• Shock Absorber Type: Oil Pressure
• Shock Absorber Design: Suspension Strut
• Shock Absorber Mounting Type: Top pin, Bottom Clamp
• Shock Absorber System: Twin-Tube
• Manufacturer: BILSTEIN
• Name: BI 17-104029
• Quality class: Q

Lisainfo: "Tootja: BILSTEIN
SEAT/VW 00-
(kvaliteediklass: Q)"

• Fitting Position: Front Axle
• Suspension: for vehicles with standard suspension
• Parameter: SFE30/20X167A
• Shock Absorber Type: Gas Pressure
• Shock Absorber Design: Suspension Strut
• Shock Absorber System: Twin-Tube
• Shock Absorber Mounting Type: Top pin
• Name: AMORT
• Manufacturer: SAA

SVHC: No information available, please contact the manufacturer!

• Fitting Position: Front Axle
• Shock Absorber Type: Gas Pressure
• Shock Absorber Design: Suspension Strut
• Shock Absorber Mounting Type: Top pin, Bottom Clamp
• Shock Absorber System: Twin-Tube
• Name: AMORT
• Manufacturer: BIL
• Quality class: Q

Additional information: "Tootja: BILSTEIN
VW POLO/GOLF, 94-
(kvaliteediklass: Q)" Lisainfo: "Tootja: BILSTEIN
VW POLO/GOLF, 94-
(kvaliteediklass: Q)"

• Fitting Position: Front Axle
• Suspension: for vehicles with bad road version
• Parameter: SFE32/22X155A
• Shock Absorber Type: Gas Pressure
• Shock Absorber Design: Suspension Strut
• Shock Absorber System: Twin-Tube
• reinforced version:
• Shock Absorber Mounting Type: Top pin
• Name: AMORT
• Manufacturer: SAA

SVHC: No information available, please contact the manufacturer!

• Name: Gas shock absorber
• Quality class: PJ

Lisainfo: "Tootja: MAGNETI MARELLI
VW GOLFIII/VENTO 94-
(kvaliteediklass: Q)"